This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips. The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.
Signed-off-by: Pavankumar Kondeti <pkondeti@xxxxxxxxxxxxxx>
---
drivers/usb/Kconfig | 1 +
drivers/usb/host/Kconfig | 11 ++
drivers/usb/host/ehci-hcd.c | 5 +
drivers/usb/host/ehci-msm.c | 290 +++++++++++++++++++++++++++++++++++++++++++
4 files changed, 307 insertions(+), 0 deletions(-)
create mode 100644 drivers/usb/host/ehci-msm.c
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index 6585f0b..b8e70a9 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -64,6 +64,7 @@ config USB_ARCH_HAS_EHCI
default y if ARCH_OMAP3
default y if ARCH_VT8500
default y if PLAT_SPEAR
+ default y if ARCH_MSM
default PCI
# ARM SA1111 chips have a non-PCI based "OHCI-compatible" USB host interface.
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 6a7c688..d8665ec 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -141,6 +141,17 @@ config USB_EHCI_HCD_OMAP
Enables support for the on-chip EHCI controller on
OMAP3 and later chips.
+config USB_EHCI_MSM
+ bool "Support for MSM on-chip EHCI USB controller"
+ depends on USB_EHCI_HCD && ARCH_MSM
+ select USB_EHCI_ROOT_HUB_TT
+ select USB_MSM_OTG_72K
+ ---help---
+ Enables support for the USB Host controller present on the
+ Qualcomm chipsets. Root Hub has inbuilt TT.
+ This driver depends on OTG driver for PHY initialization,
+ clock management, powering up VBUS.
+
config USB_EHCI_HCD_PPC_OF
bool "EHCI support for PPC USB controller on OF platform bus"
depends on USB_EHCI_HCD && PPC_OF
diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c
index abe8336..cdd3ef8 100644
--- a/drivers/usb/host/ehci-hcd.c
+++ b/drivers/usb/host/ehci-hcd.c
@@ -1231,6 +1231,11 @@ MODULE_LICENSE ("GPL");
#define PLATFORM_DRIVER spear_ehci_hcd_driver
#endif
+#ifdef CONFIG_USB_EHCI_MSM
+#include "ehci-msm.c"
+#define PLATFORM_DRIVER ehci_msm_driver
+#endif
+
#if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
!defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
!defined(XILINX_OF_PLATFORM_DRIVER)
diff --git a/drivers/usb/host/ehci-msm.c b/drivers/usb/host/ehci-msm.c
new file mode 100644
index 0000000..9ed8559
--- /dev/null
+++ b/drivers/usb/host/ehci-msm.c
@@ -0,0 +1,290 @@
+/* ehci-msm.c - HSUSB Host Controller Driver Implementation
+ *
+ * Copyright (c) 2008-2010, Code Aurora Forum. All rights reserved.
+ *
+ * Partly derived from ehci-fsl.c and ehci-hcd.c
+ * Copyright (c) 2000-2004 by David Brownell
+ * Copyright (c) 2005 MontaVista Software
+ *
+ * All source code in this file is licensed under the following license except
+ * where indicated.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ *
+ * See the GNU General Public License for more details.
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, you can find it at http://www.fsf.org
+ */
+
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+
+#include <linux/usb/otg.h>
+#include <linux/usb/msm_hsusb_hw.h>
+
+#define MSM_USB_BASE (hcd->regs)
+
+static struct otg_transceiver *otg;
+
+/*
+ * ehci_run defined in drivers/usb/host/ehci-hcd.c reset the controller and
+ * the configuration settings in ehci_msm_reset vanish after controller is
+ * reset. Resetting the controler in ehci_run seems to be un-necessary
+ * provided HCD reset the controller before calling ehci_run. Most of the HCD
+ * do but some are not. So this function is same as ehci_run but we don't
+ * reset the controller here.
+ */
+static int ehci_msm_run(struct usb_hcd *hcd)
+{
+ struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+ u32 temp;
+ u32 hcc_params;
+
+ hcd->uses_new_polling = 1;
+
+ ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
+ ehci_writel(ehci, (u32)ehci->async->qh_dma, &ehci->regs->async_next);
+
+ /*
+ * hcc_params controls whether ehci->regs->segment must (!!!)
+ * be used; it constrains QH/ITD/SITD and QTD locations.
+ * pci_pool consistent memory always uses segment zero.
+ * streaming mappings for I/O buffers, like pci_map_single(),
+ * can return segments above 4GB, if the device allows.
+ *
+ * NOTE: the dma mask is visible through dma_supported(), so
+ * drivers can pass this info along ... like NETIF_F_HIGHDMA,
+ * Scsi_Host.highmem_io, and so forth. It's readonly to all
+ * host side drivers though.
+ */
+ hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params);
+ if (HCC_64BIT_ADDR(hcc_params))
+ ehci_writel(ehci, 0, &ehci->regs->segment);
+
+ /*
+ * Philips, Intel, and maybe others need CMD_RUN before the
+ * root hub will detect new devices (why?); NEC doesn't
+ */
+ ehci->command &= ~(CMD_LRESET|CMD_IAAD|CMD_PSE|CMD_ASE|CMD_RESET);
+ ehci->command |= CMD_RUN;
+ ehci_writel(ehci, ehci->command, &ehci->regs->command);
+ dbg_cmd(ehci, "init", ehci->command);
+
+ /*
+ * Start, enabling full USB 2.0 functionality ... usb 1.1 devices
+ * are explicitly handed to companion controller(s), so no TT is
+ * involved with the root hub. (Except where one is integrated,
+ * and there's no companion controller unless maybe for USB OTG.)
+ *
+ * Turning on the CF flag will transfer ownership of all ports
+ * from the companions to the EHCI controller. If any of the
+ * companions are in the middle of a port reset at the time, it
+ * could cause trouble. Write-locking ehci_cf_port_reset_rwsem
+ * guarantees that no resets are in progress. After we set CF,
+ * a short delay lets the hardware catch up; new resets shouldn't
+ * be started before the port switching actions could complete.
+ */
+ down_write(&ehci_cf_port_reset_rwsem);
+ hcd->state = HC_STATE_RUNNING;
+ ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag);
+ ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
+ usleep_range(5000, 5500);
+ up_write(&ehci_cf_port_reset_rwsem);
+ ehci->last_periodic_enable = ktime_get_real();
+
+ temp = HC_VERSION(ehci_readl(ehci, &ehci->caps->hc_capbase));
+ ehci_info(ehci,
+ "USB %x.%x started, EHCI %x.%02x%s\n",
+ ((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f),
+ temp >> 8, temp & 0xff,
+ ignore_oc ? ", overcurrent ignored" : "");
+
+ ehci_writel(ehci, INTR_MASK,
+ &ehci->regs->intr_enable); /* Turn On Interrupts */
+
+ /* GRR this is run-once init(), being done every time the HC starts.
+ * So long as they're part of class devices, we can't do it init()
+ * since the class device isn't created that early.
+ */
+ create_debug_files(ehci);
+ create_companion_file(ehci);
+
+ return 0;
+}
+
+static int ehci_msm_reset(struct usb_hcd *hcd)
+{
+ struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+ int retval;
+
+ ehci->caps = USB_CAPLENGTH;
+ ehci->regs = USB_CAPLENGTH +
+ HC_LENGTH(ehci_readl(ehci, &ehci->caps->hc_capbase));
+
+ /* cache the data to minimize the chip reads*/
+ ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
+
+ hcd->has_tt = 1;
+ ehci->sbrn = HCD_USB2;
+
+ /* data structure init */
+ retval = ehci_init(hcd);
+ if (retval)
+ return retval;
+
+ retval = ehci_reset(ehci);
+ if (retval)
+ return retval;
+
+ /* bursts of unspecified length. */
+ writel(0, USB_AHBBURST);
+ /* Use the AHB transactor */
+ writel(0, USB_AHBMODE);
+ /* Disable streaming mode and select host mode */
+ writel(0x13, USB_USBMODE);
+
+ ehci_port_power(ehci, 1);
+ return 0;
+}
+
+static struct hc_driver msm_hc_driver = {
+ .description = hcd_name,
+ .product_desc = "Qualcomm On-Chip EHCI Host Controller",
+ .hcd_priv_size = sizeof(struct ehci_hcd),
+
+ /*
+ * generic hardware linkage
+ */
+ .irq = ehci_irq,
+ .flags = HCD_USB2 | HCD_MEMORY,
+
+ .reset = ehci_msm_reset,
+ .start = ehci_msm_run,
+
+ .stop = ehci_stop,
+ .shutdown = ehci_shutdown,
+
+ /*
+ * managing i/o requests and associated device resources
+ */
+ .urb_enqueue = ehci_urb_enqueue,
+ .urb_dequeue = ehci_urb_dequeue,
+ .endpoint_disable = ehci_endpoint_disable,
+ .endpoint_reset = ehci_endpoint_reset,
+ .clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
+
+ /*
+ * scheduling support
+ */
+ .get_frame_number = ehci_get_frame,
+
+ /*
+ * root hub support
+ */
+ .hub_status_data = ehci_hub_status_data,
+ .hub_control = ehci_hub_control,
+ .relinquish_port = ehci_relinquish_port,
+ .port_handed_over = ehci_port_handed_over,
+
+ /*
+ * PM support
+ */
+ .bus_suspend = ehci_bus_suspend,
+ .bus_resume = ehci_bus_resume,
+};
+
+static int ehci_msm_probe(struct platform_device *pdev)
+{
+ struct usb_hcd *hcd;
+ struct resource *res;
+ int ret;
+
+ dev_dbg(&pdev->dev, "ehci_msm proble\n");
+
+ hcd = usb_create_hcd(&msm_hc_driver, &pdev->dev, dev_name(&pdev->dev));
+ if (!hcd) {
+ dev_err(&pdev->dev, "Unable to create HCD\n");
+ return -ENOMEM;
+ }
+
+ hcd->irq = platform_get_irq(pdev, 0);
+ if (hcd->irq < 0) {
+ dev_err(&pdev->dev, "Unable to get IRQ resource\n");
+ ret = hcd->irq;
+ goto put_hcd;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Unable to get memory resource\n");
+ ret = -ENODEV;
+ goto put_hcd;
+ }
+
+ hcd->rsrc_start = res->start;
+ hcd->rsrc_len = resource_size(res);
+ hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+ if (!hcd->regs) {
+ dev_err(&pdev->dev, "ioremap failed\n");
+ ret = -ENOMEM;
+ goto put_hcd;
+ }
+
+ /*
+ * OTG driver takes care of PHY initialization, clock management,
+ * powering up VBUS and mapping of registers address space.
+ */
+ otg = otg_get_transceiver();
+ if (!otg) {
+ dev_err(&pdev->dev, "unable to find transceiver\n");
+ ret = -ENODEV;
+ goto unmap;
+ }
+
+ ret = otg_set_host(otg, &hcd->self);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "unable to register with transceiver\n");
+ goto put_transceiver;
+ }
+
+ device_init_wakeup(&pdev->dev, 1);
+ return 0;
+
+put_transceiver:
+ otg_put_transceiver(otg);
+unmap:
+ iounmap(hcd->regs);
+put_hcd:
+ usb_put_hcd(hcd);
+
+ return ret;
+}
+
+static int __devexit ehci_msm_remove(struct platform_device *pdev)
+{
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+ device_init_wakeup(&pdev->dev, 0);
+
+ otg_set_host(otg, NULL);
+ otg_put_transceiver(otg);
+
+ usb_put_hcd(hcd);
+
+ return 0;
+}
+
+static struct platform_driver ehci_msm_driver = {
+ .probe = ehci_msm_probe,
+ .remove = __devexit_p(ehci_msm_remove),
+ .driver = {
+ .name = "msm_hsusb_host",
+ },
+};
--
1.7.1
--
Sent by a consultant of the Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
