Re: Nobody cared about IRQs at shutdown

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



27.11.2010 20:16, Alan Stern wrote:

(sorry for the delay with the reply)

On Sat, 27 Nov 2010, Alexander E. Patrakov wrote:

26.11.2010 01:25, Alan Stern wrote:
On Thu, 25 Nov 2010, Alexander E. Patrakov wrote:

25.11.2010 21:06, Alan Stern wrote:
On Thu, 25 Nov 2010, Alexander E. Patrakov wrote:

Hello.

After switching my Gentoo desktop from sysvinit + openrc to systemd, I
started getting "nobody cared" messages about IRQs 16 and 19 (common
thing: they are assigned to the USB controllers, that's why CC:
According to your listing, they are used by uhci-hcd.  Do the messages
go away if you unload uhci-hcd before shutting down?
It is not a module here, so I have to recompile the kernel in order to
try this. Will do that tomorrow.

You may need to debug the uhci-hcd driver. Look into
drivers/usb/host/uhci-hcd.c; the uhci_shutdown() routine ought to be
called and it ought to call uhci_hc_died(), which in turn calls
uhci_reset_hc() in pci-quirks.c, which is supposed to prevent the
controller from generating any IRQs.
OK, tomorrow I will add some printks there.
Sorry, I didn't add them due to being busy with a different (non-kernel)
bug. What do you want to know - just the fact that these functions are
called before or after reporting the bad IRQ?
They should be called before the bad IRQ is reported.  That's what I
want to verify.

Yes, this is called 5 times before the bad IRQ report. I think this is consistent with the fact that I have 10 USB ports.

Even without rebuilding the kernel, you can unbind the uhci-hcd driver
from the hardware by going to the /sys/bus/pci/drivers/uhci_hcd
directory and doing:

	echo -n device-name>unbind

where "device-name" is the name of one of the symlinks in that
directory.
Thanks for the tip. Below are the updated test results, including the
ones posted in my first mail, for completeness.

1. No irqpoll, no unbind: the system reports that nobody cared for IRQs,
then waits, displays SATA errors, waits again, shuts down.

2. irqpoll, no unbind: the system shuts down without any delays.

3. No irqpoll, unbind uhci-hcd from everything it controls: the system
reports bad IRQ 19 (consumed by firewire-ohci), waits, displays SATA
errors, waits again, shuts down.
This suggests that the problem comes from the firewire controller, not
the UHCI controller.

Are you sure that you ever got "nobody cared" reports for IRQ 16?  Your
listing showed that uhci-hcd used both 16 and 19 whereas firewire-ohci
used only 19.

Yes, see the screen photo attached to the first e-mail in this thread.

4. No irqpoll, unbind both uhci-hcd and firewire-ohci from everything:
the system does not report any bad IRQs, waits, displays SATA errors,
waits again, shuts down.
And this tends to confirm it.  The SATA errors are probably a separate
issue.

What happens if you unbind firewire-ohci but not uhci-hcd?

The kernel reports the bad IRQ, waits, displays SATA errors, waits, shuts down. See the photo attached to this mail.

5. irqpoll, unbind both uhci-hcd and firewire-ohci from everything: same
as (4).

I have no firewire devices.
Apparently that doesn't stop the controller from misbehaving.  But you
need to do more tests to be sure of this.

In fact, I think that there is something bad, not specific to USB, FireWire or SATA. Without systemd, all those subsystems function properly at shutdown. With systemd, it looks like there are many mishandled interrupts (all of USB, FireWire and SATA) at shutdown. What could be this common thing? ACPI?

--
Alexander E. Patrakov

Attachment: nobody_cared_1.jpg
Description: JPEG image


[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux