Hello, a phone identified as Sony Ericsson V800-Vodafone 802SE (0fce:d008) does not work with usb-storage (it has a memory stick inside). It's detected properly, kernel reads partition table but the sda device never appears in /dev. The kernel then resets the device each 30 seconds infinitely. There's an entry in unusual_devs.h with US_FL_NO_WP_DETECT. That's correct as removing it causes the device to fail completely (even partition table is not read). Adding more flags does not help. Also tried it with older kernels - no change with 2.6.26 or even 2.4.something (don't remember). It works fine in Windows, but with some drivers installed for the CDC subdevices installed. The mass storage device shows only standard Windows driver. Any ideas? Debug log: [ 480.934312] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 480.934326] ehci_hcd 0000:00:1d.7: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT [ 480.934337] hub 1-0:1.0: port 4, status 0501, change 0001, 480 Mb/s [ 481.060025] hub 1-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 [ 481.116231] ehci_hcd 0000:00:1d.7: port 4 full speed --> companion [ 481.116239] ehci_hcd 0000:00:1d.7: GetStatus port 4 status 003801 POWER OWNER sig=j CONNECT [ 481.116257] usb usb3: wakeup_rh (auto-start) [ 481.116270] hub 1-0:1.0: port 4 not reset yet, waiting 50ms [ 481.172035] ehci_hcd 0000:00:1d.7: GetStatus port 4 status 003002 POWER OWNER sig=se0 CSC [ 481.172062] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0004 [ 481.172071] uhci_hcd 0000:00:1d.1: port 2 portsc 0093,00 [ 481.172078] hub 3-0:1.0: port 2, status 0101, change 0001, 12 Mb/s [ 481.300022] hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 [ 481.412024] usb 3-2: new full speed USB device using uhci_hcd and address 4 [ 481.568247] usb 3-2: skipped 3 descriptors after interface [ 481.568253] usb 3-2: skipped 4 descriptors after interface [ 481.568258] usb 3-2: skipped 4 descriptors after interface [ 481.568262] usb 3-2: skipped 3 descriptors after interface [ 481.568266] usb 3-2: skipped 2 descriptors after interface [ 481.573250] usb 3-2: default language 0x0409 [ 481.589239] usb 3-2: udev 4, busnum 3, minor = 259 [ 481.589244] usb 3-2: New USB device found, idVendor=0fce, idProduct=d008 [ 481.589299] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 481.589351] usb 3-2: Product: Sony Ericsson V800-Vodafone 802SE [ 481.589402] usb 3-2: Manufacturer: Sony Ericsson [ 481.589450] usb 3-2: SerialNumber: xyz [ 481.589590] usb 3-2: uevent [ 481.590223] usb 3-2: usb_probe_device [ 481.590232] usb 3-2: configuration #1 chosen from 1 choice [ 481.591180] usb 3-2: uevent [ 481.594265] usb 3-2: adding 3-2:1.0 (config #1, interface 0) [ 481.597261] usb 3-2:1.0: uevent [ 481.597288] usb 3-2: adding 3-2:1.1 (config #1, interface 1) [ 481.599251] usb 3-2:1.1: uevent [ 481.599289] usb 3-2: adding 3-2:1.2 (config #1, interface 2) [ 481.602265] usb 3-2:1.2: uevent [ 481.602315] usb 3-2: adding 3-2:1.3 (config #1, interface 3) [ 481.604268] usb 3-2:1.3: uevent [ 481.604309] usb 3-2: adding 3-2:1.4 (config #1, interface 4) [ 481.606251] usb 3-2:1.4: uevent [ 481.606300] usb 3-2: adding 3-2:1.5 (config #1, interface 5) [ 481.608308] usb 3-2:1.5: uevent [ 481.608332] usb 3-2: adding 3-2:1.6 (config #1, interface 6) [ 481.610254] usb 3-2:1.6: uevent [ 481.610278] usb 3-2: adding 3-2:1.7 (config #1, interface 7) [ 481.612297] usb 3-2:1.7: uevent [ 481.612421] usb 3-2: adding 3-2:1.8 (config #1, interface 8) [ 481.614251] usb 3-2:1.8: uevent [ 481.614408] hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 481.643977] Initializing USB Mass Storage driver... [ 481.644723] usb-storage 3-2:1.0: usb_probe_interface [ 481.644731] usb-storage 3-2:1.0: usb_probe_interface - got id [ 481.644734] usb-storage: USB Mass Storage device detected [ 481.645379] usb-storage: -- associate_dev [ 481.645384] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.645387] usb-storage: Interface Subclass: 0x08, Protocol: 0x00 [ 481.645394] usb-storage: storage_probe() failed [ 481.645397] usb-storage: -- usb_stor_release_resources [ 481.645399] usb-storage: -- sending exit command to thread [ 481.645401] usb-storage: -- dissociate_dev [ 481.645440] usb-storage 3-2:1.1: usb_probe_interface [ 481.645446] usb-storage 3-2:1.1: usb_probe_interface - got id [ 481.645449] usb-storage: USB Mass Storage device detected [ 481.645515] usb-storage: -- associate_dev [ 481.645519] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.645522] usb-storage: Interface Subclass: 0x02, Protocol: 0x01 [ 481.645527] usb-storage: Transport: Control/Bulk [ 481.645529] usb-storage: Protocol: 8020i [ 481.645531] usb-storage: Endpoint sanity check failed! Rejecting dev. [ 481.645534] usb-storage: storage_probe() failed [ 481.645536] usb-storage: -- usb_stor_release_resources [ 481.645538] usb-storage: -- sending exit command to thread [ 481.645541] usb-storage: -- dissociate_dev [ 481.645555] usb-storage: probe of 3-2:1.1 failed with error -5 [ 481.645618] usb-storage 3-2:1.2: usb_probe_interface [ 481.645623] usb-storage 3-2:1.2: usb_probe_interface - got id [ 481.645626] usb-storage: USB Mass Storage device detected [ 481.645652] usb-storage: -- associate_dev [ 481.645656] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.645659] usb-storage: Interface Subclass: 0x00, Protocol: 0x00 [ 481.645662] usb-storage: storage_probe() failed [ 481.645664] usb-storage: -- usb_stor_release_resources [ 481.645666] usb-storage: -- sending exit command to thread [ 481.645669] usb-storage: -- dissociate_dev [ 481.645687] usb-storage 3-2:1.3: usb_probe_interface [ 481.645692] usb-storage 3-2:1.3: usb_probe_interface - got id [ 481.645694] usb-storage: USB Mass Storage device detected [ 481.645715] usb-storage: -- associate_dev [ 481.645719] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.645722] usb-storage: Interface Subclass: 0x02, Protocol: 0x01 [ 481.645725] usb-storage: Transport: Control/Bulk [ 481.645727] usb-storage: Protocol: 8020i [ 481.645728] usb-storage: Endpoint sanity check failed! Rejecting dev. [ 481.645731] usb-storage: storage_probe() failed [ 481.645733] usb-storage: -- usb_stor_release_resources [ 481.645734] usb-storage: -- sending exit command to thread [ 481.645737] usb-storage: -- dissociate_dev [ 481.645748] usb-storage: probe of 3-2:1.3 failed with error -5 [ 481.645806] usb-storage 3-2:1.4: usb_probe_interface [ 481.645811] usb-storage 3-2:1.4: usb_probe_interface - got id [ 481.645813] usb-storage: USB Mass Storage device detected [ 481.645835] usb-storage: -- associate_dev [ 481.645839] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.645842] usb-storage: Interface Subclass: 0x00, Protocol: 0x00 [ 481.645845] usb-storage: storage_probe() failed [ 481.645847] usb-storage: -- usb_stor_release_resources [ 481.645849] usb-storage: -- sending exit command to thread [ 481.645852] usb-storage: -- dissociate_dev [ 481.645870] usb-storage 3-2:1.5: usb_probe_interface [ 481.645875] usb-storage 3-2:1.5: usb_probe_interface - got id [ 481.645877] usb-storage: USB Mass Storage device detected [ 481.645897] usb-storage: -- associate_dev [ 481.645900] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.645903] usb-storage: Interface Subclass: 0x0b, Protocol: 0x00 [ 481.645906] usb-storage: storage_probe() failed [ 481.645908] usb-storage: -- usb_stor_release_resources [ 481.645910] usb-storage: -- sending exit command to thread [ 481.645913] usb-storage: -- dissociate_dev [ 481.645928] usb-storage 3-2:1.6: usb_probe_interface [ 481.645933] usb-storage 3-2:1.6: usb_probe_interface - got id [ 481.645936] usb-storage: USB Mass Storage device detected [ 481.645954] usb-storage: -- associate_dev [ 481.645958] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.645960] usb-storage: Interface Subclass: 0x00, Protocol: 0x00 [ 481.645963] usb-storage: storage_probe() failed [ 481.645965] usb-storage: -- usb_stor_release_resources [ 481.645967] usb-storage: -- sending exit command to thread [ 481.645970] usb-storage: -- dissociate_dev [ 481.645986] usb-storage 3-2:1.7: usb_probe_interface [ 481.645990] usb-storage 3-2:1.7: usb_probe_interface - got id [ 481.645993] usb-storage: USB Mass Storage device detected [ 481.646012] usb-storage: -- associate_dev [ 481.646015] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.646018] usb-storage: Interface Subclass: 0x09, Protocol: 0x01 [ 481.646021] usb-storage: storage_probe() failed [ 481.646023] usb-storage: -- usb_stor_release_resources [ 481.646025] usb-storage: -- sending exit command to thread [ 481.646028] usb-storage: -- dissociate_dev [ 481.646044] usb-storage 3-2:1.8: usb_probe_interface [ 481.646049] usb-storage 3-2:1.8: usb_probe_interface - got id [ 481.646051] usb-storage: USB Mass Storage device detected [ 481.646069] usb-storage: -- associate_dev [ 481.646073] usb-storage: Vendor: 0x0fce, Product: 0xd008, Revision: 0x0000 [ 481.646076] usb-storage: Interface Subclass: 0x02, Protocol: 0x50 [ 481.646079] usb-storage: Transport: Bulk [ 481.646081] usb-storage: Protocol: 8020i [ 481.646097] scsi20 : SCSI emulation for USB Mass Storage devices [ 481.646358] usb-storage: *** thread sleeping. [ 481.646406] usbcore: registered new interface driver usb-storage [ 481.646460] USB Mass Storage support registered. [ 481.651676] usb-storage: device found at 4 [ 481.651680] usb-storage: waiting for device to settle before scanning [ 486.648033] usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=08 len=1 [ 486.649799] usb-storage: GetMaxLUN command result is 1, data is 0 [ 486.649832] usb-storage: device scan complete [ 486.649904] usb-storage: queuecommand called [ 486.649912] usb-storage: *** thread awakened. [ 486.649916] usb-storage: Command INQUIRY (6 bytes) [ 486.649918] usb-storage: 12 00 00 00 24 00 [ 486.649926] usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 12 [ 486.649930] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.650788] usb-storage: Status code 0; transferred 31/31 [ 486.650791] usb-storage: -- transfer complete [ 486.650793] usb-storage: Bulk command transfer result=0 [ 486.650796] usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries [ 486.651784] usb-storage: Status code 0; transferred 36/36 [ 486.651787] usb-storage: -- transfer complete [ 486.651789] usb-storage: Bulk data transfer result 0x0 [ 486.651791] usb-storage: Attempting to get CSW... [ 486.651794] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.652831] usb-storage: Status code 0; transferred 13/13 [ 486.652834] usb-storage: -- transfer complete [ 486.652837] usb-storage: Bulk status result = 0 [ 486.652840] usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0 [ 486.652844] usb-storage: scsi cmd done, result=0x0 [ 486.652850] usb-storage: *** thread sleeping. [ 486.653275] scsi 20:0:0:0: Direct-Access Sony Eri Memory Stick 0000 PQ: 0 ANSI: 0 [ 486.653380] usb-storage: queuecommand called [ 486.653388] usb-storage: *** thread awakened. [ 486.653391] usb-storage: Bad LUN (0:1) [ 486.653393] usb-storage: scsi cmd done, result=0x40000 [ 486.653396] usb-storage: *** thread sleeping. [ 486.653435] usb-storage: queuecommand called [ 486.653441] usb-storage: *** thread awakened. [ 486.653444] usb-storage: Bad target number (1:0) [ 486.653446] usb-storage: scsi cmd done, result=0x40000 [ 486.653448] usb-storage: *** thread sleeping. [ 486.653476] usb-storage: queuecommand called [ 486.653482] usb-storage: *** thread awakened. [ 486.653484] usb-storage: Bad target number (2:0) [ 486.653487] usb-storage: scsi cmd done, result=0x40000 [ 486.653489] usb-storage: *** thread sleeping. [ 486.653516] usb-storage: queuecommand called [ 486.653521] usb-storage: *** thread awakened. [ 486.653524] usb-storage: Bad target number (3:0) [ 486.653526] usb-storage: scsi cmd done, result=0x40000 [ 486.653529] usb-storage: *** thread sleeping. [ 486.653559] usb-storage: queuecommand called [ 486.653564] usb-storage: *** thread awakened. [ 486.653566] usb-storage: Bad target number (4:0) [ 486.653569] usb-storage: scsi cmd done, result=0x40000 [ 486.653572] usb-storage: *** thread sleeping. [ 486.653599] usb-storage: queuecommand called [ 486.653604] usb-storage: *** thread awakened. [ 486.653607] usb-storage: Bad target number (5:0) [ 486.653609] usb-storage: scsi cmd done, result=0x40000 [ 486.653612] usb-storage: *** thread sleeping. [ 486.653640] usb-storage: queuecommand called [ 486.653645] usb-storage: *** thread awakened. [ 486.653648] usb-storage: Bad target number (6:0) [ 486.653651] usb-storage: scsi cmd done, result=0x40000 [ 486.653653] usb-storage: *** thread sleeping. [ 486.653683] usb-storage: queuecommand called [ 486.653688] usb-storage: *** thread awakened. [ 486.653691] usb-storage: Bad target number (7:0) [ 486.653693] usb-storage: scsi cmd done, result=0x40000 [ 486.653696] usb-storage: *** thread sleeping. [ 486.655354] usb-storage: queuecommand called [ 486.655362] usb-storage: *** thread awakened. [ 486.655366] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 486.655369] usb-storage: 00 00 00 00 00 00 [ 486.655377] usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.655381] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.655799] usb-storage: Status code 0; transferred 31/31 [ 486.655802] usb-storage: -- transfer complete [ 486.655805] usb-storage: Bulk command transfer result=0 [ 486.655807] usb-storage: Attempting to get CSW... [ 486.655811] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.656807] usb-storage: Status code 0; transferred 13/13 [ 486.656810] usb-storage: -- transfer complete [ 486.656813] usb-storage: Bulk status result = 0 [ 486.656817] usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x1 [ 486.656820] usb-storage: -- transport indicates command failure [ 486.656822] usb-storage: Issuing auto-REQUEST_SENSE [ 486.656828] usb-storage: Bulk Command S 0x43425355 T 0x3 L 18 F 128 Trg 0 LUN 0 CL 12 [ 486.656832] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.657795] usb-storage: Status code 0; transferred 31/31 [ 486.657798] usb-storage: -- transfer complete [ 486.657801] usb-storage: Bulk command transfer result=0 [ 486.657804] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 486.658793] usb-storage: Status code 0; transferred 18/18 [ 486.658796] usb-storage: -- transfer complete [ 486.658799] usb-storage: Bulk data transfer result 0x0 [ 486.658801] usb-storage: Attempting to get CSW... [ 486.658804] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.659801] usb-storage: Status code 0; transferred 13/13 [ 486.659804] usb-storage: -- transfer complete [ 486.659808] usb-storage: Bulk status result = 0 [ 486.659811] usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0 [ 486.659815] usb-storage: -- Result from auto-sense is 0 [ 486.659819] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 486.659824] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 486.659829] usb-storage: scsi cmd done, result=0x2 [ 486.659835] usb-storage: *** thread sleeping. [ 486.659868] usb-storage: queuecommand called [ 486.659874] usb-storage: *** thread awakened. [ 486.659877] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 486.659879] usb-storage: 00 00 00 00 00 00 [ 486.659887] usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.659890] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.660800] usb-storage: Status code 0; transferred 31/31 [ 486.660804] usb-storage: -- transfer complete [ 486.660807] usb-storage: Bulk command transfer result=0 [ 486.660809] usb-storage: Attempting to get CSW... [ 486.660812] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.663246] usb-storage: Status code 0; transferred 13/13 [ 486.663249] usb-storage: -- transfer complete [ 486.663253] usb-storage: Bulk status result = 0 [ 486.663257] usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0 [ 486.663261] usb-storage: scsi cmd done, result=0x0 [ 486.663268] usb-storage: *** thread sleeping. [ 486.664601] usb-storage: queuecommand called [ 486.664612] usb-storage: *** thread awakened. [ 486.664617] usb-storage: Command READ_CAPACITY (10 bytes) [ 486.664619] usb-storage: 25 00 00 00 00 00 00 00 00 00 [ 486.664630] usb-storage: Bulk Command S 0x43425355 T 0x5 L 8 F 128 Trg 0 LUN 0 CL 12 [ 486.664634] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.664795] usb-storage: Status code 0; transferred 31/31 [ 486.664798] usb-storage: -- transfer complete [ 486.664801] usb-storage: Bulk command transfer result=0 [ 486.664804] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries [ 486.665804] usb-storage: Status code 0; transferred 8/8 [ 486.665808] usb-storage: -- transfer complete [ 486.665811] usb-storage: Bulk data transfer result 0x0 [ 486.665813] usb-storage: Attempting to get CSW... [ 486.665816] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.666798] usb-storage: Status code 0; transferred 13/13 [ 486.666802] usb-storage: -- transfer complete [ 486.666804] usb-storage: Bulk status result = 0 [ 486.666808] usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0 [ 486.666813] usb-storage: scsi cmd done, result=0x0 [ 486.666818] usb-storage: *** thread sleeping. [ 486.666853] sd 20:0:0:0: [sda] 1921024 512-byte logical blocks: (983 MB/938 MiB) [ 486.666920] sd 20:0:0:0: [sda] Assuming Write Enabled [ 486.666971] sd 20:0:0:0: [sda] Assuming drive cache: write through [ 486.667108] usb-storage: queuecommand called [ 486.667116] usb-storage: *** thread awakened. [ 486.667120] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 486.667122] usb-storage: 00 00 00 00 00 00 [ 486.667130] usb-storage: Bulk Command S 0x43425355 T 0x6 L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.667133] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.667795] usb-storage: Status code 0; transferred 31/31 [ 486.667798] usb-storage: -- transfer complete [ 486.667800] usb-storage: Bulk command transfer result=0 [ 486.667803] usb-storage: Attempting to get CSW... [ 486.667806] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.668795] usb-storage: Status code 0; transferred 13/13 [ 486.668798] usb-storage: -- transfer complete [ 486.668800] usb-storage: Bulk status result = 0 [ 486.668804] usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0 [ 486.668808] usb-storage: scsi cmd done, result=0x0 [ 486.668812] usb-storage: *** thread sleeping. [ 486.668845] usb-storage: queuecommand called [ 486.669437] usb-storage: *** thread awakened. [ 486.669444] usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) [ 486.669447] usb-storage: 1e 00 00 00 01 00 [ 486.669455] usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.669459] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.669797] usb-storage: Status code 0; transferred 31/31 [ 486.669800] usb-storage: -- transfer complete [ 486.669803] usb-storage: Bulk command transfer result=0 [ 486.669805] usb-storage: Attempting to get CSW... [ 486.669808] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.670790] usb-storage: Status code 0; transferred 13/13 [ 486.670793] usb-storage: -- transfer complete [ 486.670796] usb-storage: Bulk status result = 0 [ 486.670799] usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x0 [ 486.670803] usb-storage: scsi cmd done, result=0x0 [ 486.670808] usb-storage: *** thread sleeping. [ 486.670855] usb-storage: queuecommand called [ 486.670861] usb-storage: *** thread awakened. [ 486.670864] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 486.670866] usb-storage: 00 00 00 00 00 00 [ 486.670874] usb-storage: Bulk Command S 0x43425355 T 0x8 L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.670877] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.671790] usb-storage: Status code 0; transferred 31/31 [ 486.671793] usb-storage: -- transfer complete [ 486.671796] usb-storage: Bulk command transfer result=0 [ 486.671798] usb-storage: Attempting to get CSW... [ 486.671801] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.672793] usb-storage: Status code 0; transferred 13/13 [ 486.672797] usb-storage: -- transfer complete [ 486.672799] usb-storage: Bulk status result = 0 [ 486.672802] usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0 [ 486.672806] usb-storage: scsi cmd done, result=0x0 [ 486.672810] usb-storage: *** thread sleeping. [ 486.672845] usb-storage: queuecommand called [ 486.672850] usb-storage: *** thread awakened. [ 486.672854] usb-storage: Command READ_CAPACITY (10 bytes) [ 486.672856] usb-storage: 25 00 00 00 00 00 00 00 00 00 [ 486.672865] usb-storage: Bulk Command S 0x43425355 T 0x9 L 8 F 128 Trg 0 LUN 0 CL 12 [ 486.672868] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.673789] usb-storage: Status code 0; transferred 31/31 [ 486.673792] usb-storage: -- transfer complete [ 486.673795] usb-storage: Bulk command transfer result=0 [ 486.673798] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries [ 486.674789] usb-storage: Status code 0; transferred 8/8 [ 486.674792] usb-storage: -- transfer complete [ 486.674794] usb-storage: Bulk data transfer result 0x0 [ 486.674796] usb-storage: Attempting to get CSW... [ 486.674799] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.675781] usb-storage: Status code 0; transferred 13/13 [ 486.675783] usb-storage: -- transfer complete [ 486.675786] usb-storage: Bulk status result = 0 [ 486.675789] usb-storage: Bulk Status S 0x53425355 T 0x9 R 0 Stat 0x0 [ 486.675792] usb-storage: scsi cmd done, result=0x0 [ 486.675796] usb-storage: *** thread sleeping. [ 486.675823] sd 20:0:0:0: [sda] Assuming Write Enabled [ 486.675879] sd 20:0:0:0: [sda] Assuming drive cache: write through [ 486.675937] sda: [ 486.676029] usb-storage: queuecommand called [ 486.676192] usb-storage: *** thread awakened. [ 486.676196] usb-storage: Command READ_10 (10 bytes) [ 486.676198] usb-storage: 28 00 00 00 00 00 00 00 08 00 [ 486.676208] usb-storage: Bulk Command S 0x43425355 T 0xa L 4096 F 128 Trg 0 LUN 0 CL 12 [ 486.676211] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.676795] usb-storage: Status code 0; transferred 31/31 [ 486.676798] usb-storage: -- transfer complete [ 486.676801] usb-storage: Bulk command transfer result=0 [ 486.676804] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 486.689808] usb-storage: Status code 0; transferred 4096/4096 [ 486.689811] usb-storage: -- transfer complete [ 486.689814] usb-storage: Bulk data transfer result 0x0 [ 486.689816] usb-storage: Attempting to get CSW... [ 486.689819] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.690780] usb-storage: Status code 0; transferred 13/13 [ 486.690782] usb-storage: -- transfer complete [ 486.690785] usb-storage: Bulk status result = 0 [ 486.690788] usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0 [ 486.690792] usb-storage: scsi cmd done, result=0x0 [ 486.690796] usb-storage: *** thread sleeping. [ 486.690827] sda1 [ 486.690995] usb-storage: queuecommand called [ 486.691002] usb-storage: *** thread awakened. [ 486.691006] usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) [ 486.691008] usb-storage: 1e 00 00 00 00 00 [ 486.691016] usb-storage: Bulk Command S 0x43425355 T 0xb L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.691019] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.691810] usb-storage: Status code 0; transferred 31/31 [ 486.691812] usb-storage: -- transfer complete [ 486.691815] usb-storage: Bulk command transfer result=0 [ 486.691817] usb-storage: Attempting to get CSW... [ 486.691820] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.692793] usb-storage: Status code 0; transferred 13/13 [ 486.692797] usb-storage: -- transfer complete [ 486.692799] usb-storage: Bulk status result = 0 [ 486.692802] usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0 [ 486.692806] usb-storage: scsi cmd done, result=0x0 [ 486.692810] usb-storage: *** thread sleeping. [ 486.692948] usb-storage: queuecommand called [ 486.694129] usb-storage: *** thread awakened. [ 486.694137] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 486.694139] usb-storage: 00 00 00 00 00 00 [ 486.694148] usb-storage: Bulk Command S 0x43425355 T 0xc L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.694152] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.694794] usb-storage: Status code 0; transferred 31/31 [ 486.694798] usb-storage: -- transfer complete [ 486.694800] usb-storage: Bulk command transfer result=0 [ 486.694802] usb-storage: Attempting to get CSW... [ 486.694806] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.695802] usb-storage: Status code 0; transferred 13/13 [ 486.695806] usb-storage: -- transfer complete [ 486.695809] usb-storage: Bulk status result = 0 [ 486.695812] usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0 [ 486.695817] usb-storage: scsi cmd done, result=0x0 [ 486.695823] usb-storage: *** thread sleeping. [ 486.695867] usb-storage: queuecommand called [ 486.695873] usb-storage: *** thread awakened. [ 486.695877] usb-storage: Command READ_CAPACITY (10 bytes) [ 486.695879] usb-storage: 25 00 00 00 00 00 00 00 00 00 [ 486.695889] usb-storage: Bulk Command S 0x43425355 T 0xd L 8 F 128 Trg 0 LUN 0 CL 12 [ 486.695893] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.696796] usb-storage: Status code 0; transferred 31/31 [ 486.696799] usb-storage: -- transfer complete [ 486.696802] usb-storage: Bulk command transfer result=0 [ 486.696806] usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries [ 486.697276] usb 3-2:1.8: uevent [ 486.697454] usb 3-2: uevent [ 486.697799] usb-storage: Status code 0; transferred 8/8 [ 486.697803] usb-storage: -- transfer complete [ 486.697806] usb-storage: Bulk data transfer result 0x0 [ 486.697808] usb-storage: Attempting to get CSW... [ 486.697811] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.698869] usb-storage: Status code 0; transferred 13/13 [ 486.698872] usb-storage: -- transfer complete [ 486.698875] usb-storage: Bulk status result = 0 [ 486.698879] usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x0 [ 486.698883] usb-storage: scsi cmd done, result=0x0 [ 486.698889] usb-storage: *** thread sleeping. [ 486.698930] sd 20:0:0:0: [sda] Assuming Write Enabled [ 486.698985] sd 20:0:0:0: [sda] Assuming drive cache: write through [ 486.699039] sd 20:0:0:0: [sda] Attached SCSI removable disk [ 486.702962] usb 3-2:1.8: uevent [ 486.704511] usb-storage: queuecommand called [ 486.704527] usb-storage: *** thread awakened. [ 486.704532] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 486.704534] usb-storage: 00 00 00 00 00 00 [ 486.704544] usb-storage: Bulk Command S 0x43425355 T 0xe L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.704547] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.704788] usb-storage: Status code 0; transferred 31/31 [ 486.704791] usb-storage: -- transfer complete [ 486.704793] usb-storage: Bulk command transfer result=0 [ 486.704796] usb-storage: Attempting to get CSW... [ 486.704799] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.705780] usb-storage: Status code 0; transferred 13/13 [ 486.705782] usb-storage: -- transfer complete [ 486.705785] usb-storage: Bulk status result = 0 [ 486.705788] usb-storage: Bulk Status S 0x53425355 T 0xe R 0 Stat 0x0 [ 486.705792] usb-storage: scsi cmd done, result=0x0 [ 486.705796] usb-storage: *** thread sleeping. [ 486.705817] usb-storage: queuecommand called [ 486.705822] usb-storage: *** thread awakened. [ 486.705826] usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) [ 486.705828] usb-storage: 1e 00 00 00 01 00 [ 486.705835] usb-storage: Bulk Command S 0x43425355 T 0xf L 0 F 0 Trg 0 LUN 0 CL 12 [ 486.705838] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.706779] usb-storage: Status code 0; transferred 31/31 [ 486.706782] usb-storage: -- transfer complete [ 486.706784] usb-storage: Bulk command transfer result=0 [ 486.706786] usb-storage: Attempting to get CSW... [ 486.706789] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.707777] usb-storage: Status code 0; transferred 13/13 [ 486.707780] usb-storage: -- transfer complete [ 486.707782] usb-storage: Bulk status result = 0 [ 486.707785] usb-storage: Bulk Status S 0x53425355 T 0xf R 0 Stat 0x0 [ 486.707788] usb-storage: scsi cmd done, result=0x0 [ 486.707791] usb-storage: *** thread sleeping. [ 486.707919] usb-storage: queuecommand called [ 486.707930] usb-storage: *** thread awakened. [ 486.707934] usb-storage: Command READ_10 (10 bytes) [ 486.707936] usb-storage: 28 00 00 00 00 00 00 00 08 00 [ 486.707945] usb-storage: Bulk Command S 0x43425355 T 0x10 L 4096 F 128 Trg 0 LUN 0 CL 12 [ 486.707949] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.708843] usb-storage: Status code 0; transferred 31/31 [ 486.708847] usb-storage: -- transfer complete [ 486.708850] usb-storage: Bulk command transfer result=0 [ 486.708854] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 486.721798] usb-storage: Status code 0; transferred 4096/4096 [ 486.721801] usb-storage: -- transfer complete [ 486.721804] usb-storage: Bulk data transfer result 0x0 [ 486.721806] usb-storage: Attempting to get CSW... [ 486.721809] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 486.722777] usb-storage: Status code 0; transferred 13/13 [ 486.722779] usb-storage: -- transfer complete [ 486.722781] usb-storage: Bulk status result = 0 [ 486.722785] usb-storage: Bulk Status S 0x53425355 T 0x10 R 0 Stat 0x0 [ 486.722789] usb-storage: scsi cmd done, result=0x0 [ 486.722794] usb-storage: *** thread sleeping. [ 486.722824] usb-storage: queuecommand called [ 486.722834] usb-storage: *** thread awakened. [ 486.722838] usb-storage: Command READ_10 (10 bytes) [ 486.722840] usb-storage: 28 00 00 00 00 08 00 00 f0 00 [ 486.722850] usb-storage: Bulk Command S 0x43425355 T 0x11 L 122880 F 128 Trg 0 LUN 0 CL 12 [ 486.722853] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 486.723779] usb-storage: Status code 0; transferred 31/31 [ 486.723782] usb-storage: -- transfer complete [ 486.723784] usb-storage: Bulk command transfer result=0 [ 486.723787] usb-storage: usb_stor_bulk_transfer_sglist: xfer 122880 bytes, 30 entries [ 487.101768] usb-storage: Status code 0; transferred 122880/122880 [ 487.101771] usb-storage: -- transfer complete [ 487.101775] usb-storage: Bulk data transfer result 0x0 [ 487.101777] usb-storage: Attempting to get CSW... [ 487.101781] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 487.102743] usb-storage: Status code 0; transferred 13/13 [ 487.102746] usb-storage: -- transfer complete [ 487.102749] usb-storage: Bulk status result = 0 [ 487.102752] usb-storage: Bulk Status S 0x53425355 T 0x11 R 0 Stat 0x0 [ 487.102757] usb-storage: scsi cmd done, result=0x0 [ 487.102763] usb-storage: *** thread sleeping. [ 487.102811] usb-storage: queuecommand called [ 487.102817] usb-storage: *** thread awakened. [ 487.102820] usb-storage: Command READ_10 (10 bytes) [ 487.102822] usb-storage: 28 00 00 00 00 f8 00 00 08 00 [ 487.102832] usb-storage: Bulk Command S 0x43425355 T 0x12 L 4096 F 128 Trg 0 LUN 0 CL 12 [ 487.102835] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 487.103756] usb-storage: Status code 0; transferred 31/31 [ 487.103759] usb-storage: -- transfer complete [ 487.103762] usb-storage: Bulk command transfer result=0 [ 487.103766] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 487.115761] usb-storage: Status code 0; transferred 4096/4096 [ 487.115765] usb-storage: -- transfer complete [ 487.115767] usb-storage: Bulk data transfer result 0x0 [ 487.115769] usb-storage: Attempting to get CSW... [ 487.115773] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 487.116754] usb-storage: Status code 0; transferred 13/13 [ 487.116757] usb-storage: -- transfer complete [ 487.116760] usb-storage: Bulk status result = 0 [ 487.116763] usb-storage: Bulk Status S 0x53425355 T 0x12 R 0 Stat 0x0 [ 487.116768] usb-storage: scsi cmd done, result=0x0 [ 487.116772] usb-storage: *** thread sleeping. [ 487.116800] usb-storage: queuecommand called [ 487.116805] usb-storage: *** thread awakened. [ 487.116809] usb-storage: Command READ_10 (10 bytes) [ 487.116811] usb-storage: 28 00 00 1d 4f 80 00 00 08 00 [ 487.116820] usb-storage: Bulk Command S 0x43425355 T 0x13 L 4096 F 128 Trg 0 LUN 0 CL 12 [ 487.116823] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 487.117742] usb-storage: Status code 0; transferred 31/31 [ 487.117745] usb-storage: -- transfer complete [ 487.117747] usb-storage: Bulk command transfer result=0 [ 487.117750] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 518.000027] usb-storage: command_abort called [ 518.000033] usb-storage: usb_stor_stop_transport called [ 518.000035] usb-storage: -- cancelling sg request [ 518.002009] usb-storage: Status code -104; transferred 0/4096 [ 518.002013] usb-storage: -- transfer cancelled [ 518.002016] usb-storage: Bulk data transfer result 0x4 [ 518.002019] usb-storage: -- command was aborted [ 518.002025] usb-storage: usb_stor_pre_reset [ 518.112029] usb 3-2: reset full speed USB device using uhci_hcd and address 4 [ 518.264971] usb-storage: usb_stor_post_reset [ 518.264976] usb-storage: usb_reset_device returns 0 [ 518.264979] usb-storage: scsi command aborted [ 518.264983] usb-storage: *** thread sleeping. [ 518.264990] usb-storage: queuecommand called [ 518.264993] usb-storage: *** thread awakened. [ 518.264997] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 518.264999] usb-storage: 00 00 00 00 00 00 [ 518.265008] usb-storage: Bulk Command S 0x43425355 T 0x14 L 0 F 0 Trg 0 LUN 0 CL 12 [ 518.265011] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 518.266964] usb-storage: Status code 0; transferred 31/31 [ 518.266966] usb-storage: -- transfer complete [ 518.266969] usb-storage: Bulk command transfer result=0 [ 518.266971] usb-storage: Attempting to get CSW... [ 518.266973] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 518.267962] usb-storage: Status code 0; transferred 13/13 [ 518.267964] usb-storage: -- transfer complete [ 518.267967] usb-storage: Bulk status result = 0 [ 518.267970] usb-storage: Bulk Status S 0x53425355 T 0x14 R 0 Stat 0x1 [ 518.267973] usb-storage: -- transport indicates command failure [ 518.267975] usb-storage: Issuing auto-REQUEST_SENSE [ 518.267979] usb-storage: Bulk Command S 0x43425355 T 0x15 L 18 F 128 Trg 0 LUN 0 CL 12 [ 518.267982] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 518.268976] usb-storage: Status code 0; transferred 31/31 [ 518.268980] usb-storage: -- transfer complete [ 518.268982] usb-storage: Bulk command transfer result=0 [ 518.268986] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 518.269971] usb-storage: Status code 0; transferred 18/18 [ 518.269974] usb-storage: -- transfer complete [ 518.269976] usb-storage: Bulk data transfer result 0x0 [ 518.269979] usb-storage: Attempting to get CSW... [ 518.269981] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 518.270962] usb-storage: Status code 0; transferred 13/13 [ 518.270964] usb-storage: -- transfer complete [ 518.270966] usb-storage: Bulk status result = 0 [ 518.270970] usb-storage: Bulk Status S 0x53425355 T 0x15 R 0 Stat 0x0 [ 518.270973] usb-storage: -- Result from auto-sense is 0 [ 518.270975] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 518.270980] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 518.270984] usb-storage: scsi cmd done, result=0x2 [ 518.270988] usb-storage: *** thread sleeping. [ 518.270995] usb-storage: queuecommand called [ 518.270999] usb-storage: *** thread awakened. [ 518.271002] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 518.271004] usb-storage: 00 00 00 00 00 00 [ 518.271011] usb-storage: Bulk Command S 0x43425355 T 0x16 L 0 F 0 Trg 0 LUN 0 CL 12 [ 518.271014] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 518.271961] usb-storage: Status code 0; transferred 31/31 [ 518.271964] usb-storage: -- transfer complete [ 518.271966] usb-storage: Bulk command transfer result=0 [ 518.271968] usb-storage: Attempting to get CSW... [ 518.271971] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 518.272974] usb-storage: Status code 0; transferred 13/13 [ 518.272977] usb-storage: -- transfer complete [ 518.272980] usb-storage: Bulk status result = 0 [ 518.272983] usb-storage: Bulk Status S 0x53425355 T 0x16 R 0 Stat 0x0 [ 518.272987] usb-storage: scsi cmd done, result=0x0 [ 518.272991] usb-storage: *** thread sleeping. [ 518.273028] usb-storage: queuecommand called [ 518.273034] usb-storage: *** thread awakened. [ 518.273038] usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) [ 518.273040] usb-storage: 1e 00 00 00 01 00 [ 518.273047] usb-storage: Bulk Command S 0x43425355 T 0x17 L 0 F 0 Trg 0 LUN 0 CL 12 [ 518.273051] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 518.273973] usb-storage: Status code 0; transferred 31/31 [ 518.273976] usb-storage: -- transfer complete [ 518.273979] usb-storage: Bulk command transfer result=0 [ 518.273981] usb-storage: Attempting to get CSW... [ 518.273983] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 518.274960] usb-storage: Status code 0; transferred 13/13 [ 518.274963] usb-storage: -- transfer complete [ 518.274965] usb-storage: Bulk status result = 0 [ 518.274968] usb-storage: Bulk Status S 0x53425355 T 0x17 R 0 Stat 0x0 [ 518.274972] usb-storage: scsi cmd done, result=0x0 [ 518.274976] usb-storage: *** thread sleeping. [ 518.274993] usb-storage: queuecommand called [ 518.274998] usb-storage: *** thread awakened. [ 518.275001] usb-storage: Command READ_10 (12 bytes) [ 518.275003] usb-storage: 28 00 00 1d 4f 80 00 00 08 00 00 00 [ 518.275013] usb-storage: Bulk Command S 0x43425355 T 0x18 L 4096 F 128 Trg 0 LUN 0 CL 12 [ 518.275017] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 518.275962] usb-storage: Status code 0; transferred 31/31 [ 518.275964] usb-storage: -- transfer complete [ 518.275967] usb-storage: Bulk command transfer result=0 [ 518.275970] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries [ 549.000023] usb-storage: command_abort called [ 549.000029] usb-storage: usb_stor_stop_transport called [ 549.000031] usb-storage: -- cancelling sg request [ 549.001243] usb-storage: Status code -104; transferred 0/4096 [ 549.001247] usb-storage: -- transfer cancelled [ 549.001250] usb-storage: Bulk data transfer result 0x4 [ 549.001253] usb-storage: -- command was aborted [ 549.001259] usb-storage: usb_stor_pre_reset [ 549.112029] usb 3-2: reset full speed USB device using uhci_hcd and address 4 [ 549.264204] usb-storage: usb_stor_post_reset [ 549.264209] usb-storage: usb_reset_device returns 0 [ 549.264212] usb-storage: scsi command aborted [ 549.264216] usb-storage: *** thread sleeping. [ 549.264223] usb-storage: queuecommand called [ 549.264227] usb-storage: *** thread awakened. [ 549.264230] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 549.264232] usb-storage: 00 00 00 00 00 00 [ 549.264240] usb-storage: Bulk Command S 0x43425355 T 0x19 L 0 F 0 Trg 0 LUN 0 CL 12 [ 549.264244] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 549.266198] usb-storage: Status code 0; transferred 31/31 [ 549.266200] usb-storage: -- transfer complete [ 549.266202] usb-storage: Bulk command transfer result=0 [ 549.266205] usb-storage: Attempting to get CSW... [ 549.266207] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 549.267196] usb-storage: Status code 0; transferred 13/13 [ 549.267199] usb-storage: -- transfer complete [ 549.267201] usb-storage: Bulk status result = 0 [ 549.267204] usb-storage: Bulk Status S 0x53425355 T 0x19 R 0 Stat 0x1 [ 549.267207] usb-storage: -- transport indicates command failure [ 549.267209] usb-storage: Issuing auto-REQUEST_SENSE [ 549.267213] usb-storage: Bulk Command S 0x43425355 T 0x1a L 18 F 128 Trg 0 LUN 0 CL 12 [ 549.267217] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 549.268206] usb-storage: Status code 0; transferred 31/31 [ 549.268208] usb-storage: -- transfer complete [ 549.268211] usb-storage: Bulk command transfer result=0 [ 549.268214] usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries [ 549.269212] usb-storage: Status code 0; transferred 18/18 [ 549.269215] usb-storage: -- transfer complete [ 549.269218] usb-storage: Bulk data transfer result 0x0 [ 549.269220] usb-storage: Attempting to get CSW... [ 549.269223] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 549.270202] usb-storage: Status code 0; transferred 13/13 [ 549.270206] usb-storage: -- transfer complete [ 549.270208] usb-storage: Bulk status result = 0 [ 549.270211] usb-storage: Bulk Status S 0x53425355 T 0x1a R 0 Stat 0x0 [ 549.270214] usb-storage: -- Result from auto-sense is 0 [ 549.270217] usb-storage: -- code: 0x70, key: 0x6, ASC: 0x29, ASCQ: 0x0 [ 549.270222] usb-storage: Unit Attention: Power on, reset, or bus device reset occurred [ 549.270227] usb-storage: scsi cmd done, result=0x2 [ 549.270231] usb-storage: *** thread sleeping. [ 549.270237] usb-storage: queuecommand called [ 549.270241] usb-storage: *** thread awakened. [ 549.270244] usb-storage: Command TEST_UNIT_READY (6 bytes) [ 549.270246] usb-storage: 00 00 00 00 00 00 [ 549.270253] usb-storage: Bulk Command S 0x43425355 T 0x1b L 0 F 0 Trg 0 LUN 0 CL 12 [ 549.270257] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 549.271197] usb-storage: Status code 0; transferred 31/31 [ 549.271199] usb-storage: -- transfer complete [ 549.271202] usb-storage: Bulk command transfer result=0 [ 549.271204] usb-storage: Attempting to get CSW... [ 549.271206] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 549.272206] usb-storage: Status code 0; transferred 13/13 [ 549.272209] usb-storage: -- transfer complete [ 549.272212] usb-storage: Bulk status result = 0 [ 549.272215] usb-storage: Bulk Status S 0x53425355 T 0x1b R 0 Stat 0x0 [ 549.272218] usb-storage: scsi cmd done, result=0x0 [ 549.272221] usb-storage: *** thread sleeping. [ 549.272251] usb-storage: queuecommand called [ 549.272257] usb-storage: *** thread awakened. [ 549.272260] usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) [ 549.272263] usb-storage: 1e 00 00 00 01 00 [ 549.272270] usb-storage: Bulk Command S 0x43425355 T 0x1c L 0 F 0 Trg 0 LUN 0 CL 12 [ 549.272273] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 549.273208] usb-storage: Status code 0; transferred 31/31 [ 549.273212] usb-storage: -- transfer complete [ 549.273214] usb-storage: Bulk command transfer result=0 [ 549.273216] usb-storage: Attempting to get CSW... [ 549.273219] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes [ 549.274205] usb-storage: Status code 0; transferred 13/13 [ 549.274209] usb-storage: -- transfer complete [ 549.274211] usb-storage: Bulk status result = 0 [ 549.274214] usb-storage: Bulk Status S 0x53425355 T 0x1c R 0 Stat 0x0 [ 549.274218] usb-storage: scsi cmd done, result=0x0 [ 549.274222] usb-storage: *** thread sleeping. [ 549.274243] usb-storage: queuecommand called [ 549.274248] usb-storage: *** thread awakened. [ 549.274252] usb-storage: Command READ_10 (12 bytes) [ 549.274254] usb-storage: 28 00 00 1d 4f 80 00 00 08 00 00 00 [ 549.274264] usb-storage: Bulk Command S 0x43425355 T 0x1d L 4096 F 128 Trg 0 LUN 0 CL 12 [ 549.274267] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 549.275196] usb-storage: Status code 0; transferred 31/31 [ 549.275199] usb-storage: -- transfer complete [ 549.275201] usb-storage: Bulk command transfer result=0 [ 549.275205] usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries I unplugged it here. [ 550.633075] usb 3-2: uhci_result_common: failed with status 440000 [ 550.633105] usb-storage: Status code -84; transferred 0/4096 [ 550.633108] usb-storage: -- unknown error [ 550.633111] usb-storage: Bulk data transfer result 0x4 [ 550.633114] usb-storage: -- transport indicates error, resetting [ 550.633120] usb-storage: usb_stor_pre_reset [ 550.688059] hub 3-0:1.0: logical disconnect on port 2 [ 550.688068] usb-storage: usb_stor_post_reset [ 550.688072] usb-storage: usb_reset_device returns -19 [ 550.688076] usb-storage: usb_stor_Bulk_reset called [ 550.688081] usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=08 len=0 [ 550.688085] usb-storage: Soft reset failed: -19 [ 550.688088] usb-storage: scsi cmd done, result=0x70000 [ 550.688092] usb-storage: *** thread sleeping. [ 550.688099] hub 3-0:1.0: state 7 ports 2 chg 0004 evt 0000 [ 550.688108] hub 3-0:1.0: port 2, status 0100, change 0000, 12 Mb/s [ 550.688112] usb 3-2: USB disconnect, address 4 [ 550.688164] usb 3-2: unregistering device [ 550.688167] usb 3-2: usb_disable_device nuking all URBs [ 550.688175] usb 3-2: unregistering interface 3-2:1.0 [ 550.688230] usb 3-2:1.0: uevent [ 550.688259] usb-storage: queuecommand called [ 550.688274] usb 3-2: unregistering interface 3-2:1.1 [ 550.688314] usb 3-2:1.1: uevent [ 550.688331] usb 3-2: unregistering interface 3-2:1.2 [ 550.688371] usb 3-2:1.2: uevent [ 550.688387] usb 3-2: unregistering interface 3-2:1.3 [ 550.688419] usb 3-2:1.3: uevent [ 550.688434] usb 3-2: unregistering interface 3-2:1.4 [ 550.688476] usb 3-2:1.4: uevent [ 550.688490] usb 3-2: unregistering interface 3-2:1.5 [ 550.688513] usb 3-2:1.5: uevent [ 550.688528] usb 3-2: unregistering interface 3-2:1.6 [ 550.688551] usb 3-2:1.6: uevent [ 550.688564] usb 3-2: unregistering interface 3-2:1.7 [ 550.688597] usb 3-2:1.7: uevent [ 550.688612] usb 3-2: unregistering interface 3-2:1.8 [ 550.688656] usb-storage: storage_disconnect() called [ 550.689061] usb-storage: -- usb_stor_release_resources [ 550.689064] usb-storage: -- sending exit command to thread [ 550.692927] usb-storage: *** thread awakened. [ 550.692936] usb-storage: Command READ_10 (12 bytes) [ 550.692938] usb-storage: 28 00 00 1d 4f 80 00 00 08 00 00 00 [ 550.692951] usb-storage: Bulk Command S 0x43425355 T 0x1e L 4096 F 128 Trg 0 LUN 0 CL 12 [ 550.692956] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes [ 550.692961] usb-storage: Status code -19; transferred 0/31 [ 550.692964] usb-storage: -- unknown error [ 550.692966] usb-storage: Bulk command transfer result=4 [ 550.692969] usb-storage: -- transport indicates error, resetting [ 550.692973] usb-storage: unable to lock device for reset: -19 [ 550.692976] usb-storage: usb_stor_Bulk_reset called [ 550.692979] usb-storage: No reset during disconnect [ 550.692982] usb-storage: scsi cmd done, result=0x70000 [ 550.692987] usb-storage: *** thread sleeping. [ 550.692990] usb-storage: *** thread awakened. [ 550.692992] usb-storage: -- exiting [ 550.693028] scsi 20:0:0:0: [sda] Unhandled error code [ 550.693082] scsi 20:0:0:0: [sda] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK [ 550.693177] scsi 20:0:0:0: [sda] CDB: Read(10): 28 00 00 1d 4f 80 00 00 08 00 00 00 [ 550.693772] end_request: I/O error, dev sda, sector 1920896 [ 550.693824] Buffer I/O error on device sda, logical block 240112 [ 550.696628] usb-storage: -- dissociate_dev [ 550.696685] usb 3-2:1.8: uevent [ 550.696846] usb 3-2: uevent [ 550.733270] usb usb3: uevent [ 551.968033] usb usb3: suspend_rh (auto-stop) -- Ondrej Zary -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
