I aggregated and ported all usb patches I have previously posted which
are not mainlined into a single series aimed at providing a stable usb
console.
Greg Kroah-Hartman already picked up the first 2 patches in the
series, but for completeness they are provided here because one of the
other patches requires the context changes.
Differences in V2 vs V1 patch set
* The optimize usb sysrq was dropped entirely
* Removed the unused export symbol per Alan Stern's comments
* Updated the definition of usb_poll_irq() per Alan Stern's comments
Thanks,
Jason.
-- The recap about synchronous usb serial consoles --
This is picking up where Alan Stern and I left off after a discussion
in September 2009.
The serial uart code implements the console writes synchronously such
that you get the data right away and "pay the toll" in terms of system
performance loss if you do lots of printk's to the console. The usb
serial console code just eats the data if there is no room left in the
queue, and you do not see the data until the interrupts are restored.
If we assume the main reason you would use a usb console device is to
get printk's then every effort should be made to be able to see the
printk's on the usb console device. In this patch series, two
conditions must be met before the hcd device would get polled.
1) The data write is a usb serial console write
2) The usb serial driver has set the variable max_in_flight_urbs
Based on Alan's comments about the 1ms minimum response time for the
hcd device I ended up using a maximum 3ms delay loop. The 3ms was
selected based on testing the usb_debug device and the ftdi usb rs232
port. I found the usb_debug device needed the 1ms and the ftdi device
required slightly more than 2ms in the worst case else there was some
sporadic data loss.
I also tested incurring the penalty 3ms for each write with the device
in a "failed" capacity. In that case it introduced a 3ms delay for
each printk() which only showed any noticeable delay with the "SysRq t"
packet.
Part of having the console stable requires that usb sysrq handler get
executed in a tasklet. The hcd device lock is always held while the
driver call backs are executed. The means you cannot get the sysrq
printk's out to the usb console device after the in_flight urb queue
is filled.
Thanks,
Jason.
---
The following changes since commit a3d3203e4bb40f253b1541e310dc0f9305be7c84:
Linus Torvalds (1):
Merge branch 'release' of git://git.kernel.org/.../lenb/linux-acpi-2.6
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb.git for_gregkh
Jason Wessel (5):
tty_port,usb-console: Fix usb serial console open/close regression
usb-serial: Use tty_port version of console instead of the usb_serial_port version
usb-console: pass baud from console to the initial tty open
usb-hcd,usb-console: poll hcd device to force usb console writes
usb-serialy,sysrq: Run the sysrq handler in a tasklet
drivers/char/sysrq.c | 29 ++++++++++++++++
drivers/char/tty_port.c | 2 +-
drivers/usb/core/hcd.c | 10 +++++
drivers/usb/serial/console.c | 70 ++++++++++++++++++++++----------------
drivers/usb/serial/ftdi_sio.c | 9 +++--
drivers/usb/serial/generic.c | 6 ++--
drivers/usb/serial/pl2303.c | 8 +++--
drivers/usb/serial/usb-serial.c | 4 +-
drivers/usb/serial/usb_debug.c | 2 +-
include/linux/sysrq.h | 4 ++
include/linux/tty.h | 1 +
include/linux/usb.h | 3 ++
include/linux/usb/serial.h | 2 -
13 files changed, 104 insertions(+), 46 deletions(-)
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
