On lauantai 13 helmikuu 2010 09:11:36 Oliver Neukum wrote: > Am Samstag, 13. Februar 2010 03:50:04 schrieb Alan Stern: > > On Sat, 13 Feb 2010, Anssi Hannula wrote: > > > On 05.02.2010 23:59, Oliver Neukum wrote: > > > > Am Freitag, 5. Februar 2010 20:58:17 schrieb Matthew Garrett: > > > >> drivers/usb/serial/usb-serial.c: usb_serial_port_work - port 0 > > > >> drivers/usb/serial/usb-serial.c: serial_write - port 0, 2048 byte(s) > > > >> drivers/usb/serial/generic.c: usb_serial_generic_write - port 0, > > > >> 2048 bytes drivers/usb/serial/generic.c: usb_serial_generic_write - > > > >> put 512 bytes into fifo drivers/usb/serial/usb-serial.c: > > > >> serial_write - port 0, 1536 byte(s) drivers/usb/serial/generic.c: > > > >> usb_serial_generic_write - port 0, 1536 bytes > > > >> drivers/usb/serial/generic.c: usb_serial_generic_write - put 0 > > > >> bytes into fifo drivers/usb/serial/generic.c: > > > >> usb_serial_generic_write - FIFO is full > > > > > > > > OK, could you also get an usbmon trace? This would allow a > > > > determination whether the submitted URB doesn't finish for some > > > > reason, or whether no URB is submitted, possibly because a wakeup is > > > > missed. > > > > > > I'm also affected by this regression. Here's an usbmon trace of > > > gobi_loader hanging: > > > http://stuff.onse.fi/gobi2000/gobi-regression.mon.log > > > > That's odd. The log shows the final bulk-OUT transfer was cancelled > > after less than 1 ms. Is there a timeout value somewhere that is too > > small by a factor of 1000? > > Neither qcserial nor usb-serial implement timeouts. > Is it possible that this is caused by user space closing the handle > causing usb-serial::port_release() to call kill_traffic()? > > Anssi, going by your log the last write is quite short and begins > with 342d3030 39202020 20202020 20202020 801d9b80 02000000 3512dcfe > 44313032. Does this match with the last part of the firmware you are > transfering? Yes. (there are three files, this is the last part of the third file) > Could you put an "mdelay(500);" at the beginning of > usb-serial::port_release() and retest? It seems I can't get that far anymore, it hangs much more early now: http://stuff.onse.fi/gobi2000/gobi-regression2.mon.log After interrupting gobi_loader I get a WARNING: http://stuff.onse.fi/gobi2000/gobi-regression2.warning.log Trying gobi_loader again immediately, the log is almost empty: http://stuff.onse.fi/gobi2000/gobi-regression3.mon.log After reboot I get a similar log as regression2: http://stuff.onse.fi/gobi2000/gobi-regression4.mon.log Actually, just now I noticed that the first time I had some extra sleep calls before starting the firmware upload in gobi_loader, which caused it to successfully finish (i.e. not hang; I guess somehow I didn't notice it when I logged the first usbmon.log), but the firmware wasn't still uploaded properly (that'd be because of the cancelled transfer I guess). I'll get back to this later today, including testing with mdelay in port_release with the extra sleep calls in gobi_loader. -- Anssi Hannula -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
