On Thu, Feb 27, 2025 at 04:12:54PM +0100, Alexander Stein wrote:
> Hi,
>
> Am Donnerstag, 27. Februar 2025, 10:53:46 CET schrieb Xu Yang:
> > On i.MX95 platform, USB wakeup setting is controlled by HSIO Block
> > Control:
> >
> > HSIO Block Control Overview:
> > - The HSIO block control include configuration and status registers that
> > provide miscellaneous top-level controls for clocking, beat limiter
> > enables, wakeup signal enables and interrupt status for the PCIe and USB
> > interfaces.
> >
> > The wakeup function of HSIO blkctl is basically same as non-core, except
> > improvements about power lost cases. This will add the wakeup setting for
> > HSIO blkctl on i.MX95. It will firstly ioremap hsio blkctl memory, then do
> > wakeup setting as needs.
> >
> > Reviewed-by: Frank Li <Frank.Li@xxxxxxx>
> > Reviewed-by: Jun Li <jun.li@xxxxxxx>
> > Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx>
> >
> > ---
> > Changes in v3:
> > - remove usbmisc_imx95_init(), use usbmisc_imx7d_init()
> > Changes in v2:
> > - add Rb tag
> > ---
> > drivers/usb/chipidea/usbmisc_imx.c | 72 ++++++++++++++++++++++++++++++
> > 1 file changed, 72 insertions(+)
> >
> > diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c
> > index 1394881fde5f..8c30908c11ed 100644
> > --- a/drivers/usb/chipidea/usbmisc_imx.c
> > +++ b/drivers/usb/chipidea/usbmisc_imx.c
> > @@ -139,6 +139,22 @@
> > #define MX6_USB_OTG_WAKEUP_BITS (MX6_BM_WAKEUP_ENABLE | MX6_BM_VBUS_WAKEUP | \
> > MX6_BM_ID_WAKEUP | MX6SX_BM_DPDM_WAKEUP_EN)
> >
> > +/*
> > + * HSIO Block Control Register
> > + */
> > +
> > +#define BLKCTL_USB_WAKEUP_CTRL 0x0
> > +#define BLKCTL_OTG_WAKE_ENABLE BIT(31)
> > +#define BLKCTL_OTG_VBUS_SESSVALID BIT(4)
> > +#define BLKCTL_OTG_ID_WAKEUP_EN BIT(2)
> > +#define BLKCTL_OTG_VBUS_WAKEUP_EN BIT(1)
> > +#define BLKCTL_OTG_DPDM_WAKEUP_EN BIT(0)
> > +
> > +#define BLKCTL_WAKEUP_SOURCE (BLKCTL_OTG_WAKE_ENABLE | \
> > + BLKCTL_OTG_ID_WAKEUP_EN | \
> > + BLKCTL_OTG_VBUS_WAKEUP_EN | \
> > + BLKCTL_OTG_DPDM_WAKEUP_EN)
> > +
> > struct usbmisc_ops {
> > /* It's called once when probe a usb device */
> > int (*init)(struct imx_usbmisc_data *data);
> > @@ -159,6 +175,7 @@ struct usbmisc_ops {
> >
> > struct imx_usbmisc {
> > void __iomem *base;
> > + void __iomem *blkctl;
> > spinlock_t lock;
> > const struct usbmisc_ops *ops;
> > };
> > @@ -1016,6 +1033,41 @@ static int usbmisc_imx6sx_power_lost_check(struct imx_usbmisc_data *data)
> > return 0;
> > }
> >
> > +static u32 usbmisc_blkctl_wakeup_setting(struct imx_usbmisc_data *data)
> > +{
> > + u32 wakeup_setting = BLKCTL_WAKEUP_SOURCE;
> > +
> > + if (data->ext_id || data->available_role != USB_DR_MODE_OTG)
> > + wakeup_setting &= ~BLKCTL_OTG_ID_WAKEUP_EN;
> > +
> > + if (data->ext_vbus || data->available_role == USB_DR_MODE_HOST)
> > + wakeup_setting &= ~BLKCTL_OTG_VBUS_WAKEUP_EN;
> > +
> > + /* Select session valid as VBUS wakeup source */
> > + wakeup_setting |= BLKCTL_OTG_VBUS_SESSVALID;
> > +
> > + return wakeup_setting;
> > +}
> > +
> > +static int usbmisc_imx95_set_wakeup(struct imx_usbmisc_data *data, bool enabled)
> > +{
> > + struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
> > + unsigned long flags;
> > + u32 val;
> > +
> > + spin_lock_irqsave(&usbmisc->lock, flags);
> > + val = readl(usbmisc->blkctl + BLKCTL_USB_WAKEUP_CTRL);
> > + val &= ~BLKCTL_WAKEUP_SOURCE;
> > +
> > + if (enabled)
> > + val |= usbmisc_blkctl_wakeup_setting(data);
> > +
> > + writel(val, usbmisc->blkctl + BLKCTL_USB_WAKEUP_CTRL);
> > + spin_unlock_irqrestore(&usbmisc->lock, flags);
>
> usbmisc->blkctl is NULL if DT does not provide a 2nd IORESOURCE_MEM.
Good catch. Thanks!
It may return an errno if usbmisc->blkctl is NULL.
>
> > +
> > + return 0;
> > +}
> > +
> > static const struct usbmisc_ops imx25_usbmisc_ops = {
> > .init = usbmisc_imx25_init,
> > .post = usbmisc_imx25_post,
> > @@ -1068,6 +1120,14 @@ static const struct usbmisc_ops imx7ulp_usbmisc_ops = {
> > .power_lost_check = usbmisc_imx7d_power_lost_check,
> > };
> >
> > +static const struct usbmisc_ops imx95_usbmisc_ops = {
> > + .init = usbmisc_imx7d_init,
> > + .set_wakeup = usbmisc_imx95_set_wakeup,
> > + .charger_detection = imx7d_charger_detection,
> > + .power_lost_check = usbmisc_imx7d_power_lost_check,
> > + .vbus_comparator_on = usbmisc_imx7d_vbus_comparator_on,
> > +};
> > +
> > static inline bool is_imx53_usbmisc(struct imx_usbmisc_data *data)
> > {
> > struct imx_usbmisc *usbmisc = dev_get_drvdata(data->dev);
> > @@ -1289,6 +1349,10 @@ static const struct of_device_id usbmisc_imx_dt_ids[] = {
> > .compatible = "fsl,imx8ulp-usbmisc",
> > .data = &imx7ulp_usbmisc_ops,
> > },
> > + {
> > + .compatible = "fsl,imx95-usbmisc",
> > + .data = &imx95_usbmisc_ops,
> > + },
> > { /* sentinel */ }
> > };
> > MODULE_DEVICE_TABLE(of, usbmisc_imx_dt_ids);
> > @@ -1296,6 +1360,7 @@ MODULE_DEVICE_TABLE(of, usbmisc_imx_dt_ids);
> > static int usbmisc_imx_probe(struct platform_device *pdev)
> > {
> > struct imx_usbmisc *data;
> > + struct resource *res;
> >
> > data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > if (!data)
> > @@ -1307,6 +1372,13 @@ static int usbmisc_imx_probe(struct platform_device *pdev)
> > if (IS_ERR(data->base))
> > return PTR_ERR(data->base);
> >
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> > + if (res) {
> > + data->blkctl = devm_ioremap_resource(&pdev->dev, res);
> > + if (IS_ERR(data->blkctl))
> > + return PTR_ERR(data->blkctl);
> > + }
> > +
>
> Any chance to ensure imx95 has actually data->blkctl?
I think let usbmisc_imx95_set_wakeup() return an error should be enough.
Some errors will be printed for user. Also dt-bindings has restriction for
imx95.
Thanks,
Xu Yang
