Re: [PATCH 5/5] arm64: dts: qcom: gaokun3: Add Embedded Controller node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 27.12.2024 6:13 PM, Pengyu Luo wrote:
> The Embedded Controller in the Huawei Matebook E Go (s8280xp)
> is accessible on &i2c15 and provides battery and adapter status,
> port orientation status, as well as HPD event notifications for
> two USB Type-C port, etc.
> 
> Add the EC to the device tree and describe the relationship among
> the type-c ports, orientation switches and the QMP combo PHY.
> 
> Signed-off-by: Pengyu Luo <mitltlatltl@xxxxxxxxx>
> ---
>  .../boot/dts/qcom/sc8280xp-huawei-gaokun3.dts | 139 ++++++++++++++++++
>  1 file changed, 139 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-huawei-gaokun3.dts b/arch/arm64/boot/dts/qcom/sc8280xp-huawei-gaokun3.dts
> index 09b95f89e..09ca9a560 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-huawei-gaokun3.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-huawei-gaokun3.dts
> @@ -28,6 +28,7 @@ / {
>  
>  	aliases {
>  		i2c4 = &i2c4;
> +		i2c15 = &i2c15;
>  		serial1 = &uart2;
>  	};
>  
> @@ -216,6 +217,40 @@ map1 {
>  		};
>  	};
>  
> +	usb0-sbu-mux {
> +			compatible = "pericom,pi3usb102", "gpio-sbu-mux";
> +
> +			select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
> +
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&usb0_sbu_default>;

Please preserve this order:

property-n
property-names

> +
> +			orientation-switch;

This

> +
> +			port {
> +				usb0_sbu_mux: endpoint {
> +						remote-endpoint = <&ucsi0_sbu>;

And this section have incorrect whitespacing (one tab too many, make
sure you set your tab width to 8 spaces)

Same for usb1-sbu-mux

[...]

> +	i2c15_default: i2c15-default-state {
> +		pins = "gpio36", "gpio37";
> +		function = "qup15";
> +		drive-strength = <2>;
> +		bias-pull-up;
> +	};
> +
>  	mode_pin_active: mode-pin-state {
>  		pins = "gpio26";
>  		function = "gpio";
> @@ -1301,6 +1426,20 @@ tx-pins {
>  		};
>  	};
>  
> +	usb0_sbu_default: usb0-sbu-state {
> +		pins = "gpio164";
> +		function = "gpio";
> +		bias-disable;
> +		drive-strength = <16>;
> +	};
> +
> +	usb1_sbu_default: usb1-sbu-state {
> +		pins = "gpio47";
> +		function = "gpio";
> +		bias-disable;
> +		drive-strength = <16>;
> +	};

Similarly, please keep drive-strength above bias for consistency

lgtm otherwise

Konrad




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux