This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx>
---
Rickard, I finally decided that the right thing to do was to add an
msleep(10) to the place where remote_wakeup() is called, instead of
adding it to remote_wakeup(). This patch should fix the problems you
were seeing with your cdc-ether device just as well as the changes we
discussed earlier.
Alan Stern
Index: usb-2.6/drivers/usb/core/hub.c
===================================================================
--- usb-2.6.orig/drivers/usb/core/hub.c
+++ usb-2.6/drivers/usb/core/hub.c
@@ -3358,6 +3358,9 @@ static void hub_events(void)
USB_PORT_FEAT_C_SUSPEND);
udev = hdev->children[i-1];
if (udev) {
+ /* TRSMRCY = 10 msec */
+ msleep(10);
+
usb_lock_device(udev);
ret = remote_wakeup(hdev->
children[i-1]);
Index: usb-2.6/drivers/usb/host/ehci-hcd.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/ehci-hcd.c
+++ usb-2.6/drivers/usb/host/ehci-hcd.c
@@ -787,9 +787,10 @@ static irqreturn_t ehci_irq (struct usb_
/* start 20 msec resume signaling from this port,
* and make khubd collect PORT_STAT_C_SUSPEND to
- * stop that signaling.
+ * stop that signaling. Use 5 ms extra for safety,
+ * like usb_port_resume() does.
*/
- ehci->reset_done [i] = jiffies + msecs_to_jiffies (20);
+ ehci->reset_done[i] = jiffies + msecs_to_jiffies(25);
ehci_dbg (ehci, "port %d remote wakeup\n", i + 1);
mod_timer(&hcd->rh_timer, ehci->reset_done[i]);
}
Index: usb-2.6/drivers/usb/host/uhci-hub.c
===================================================================
--- usb-2.6.orig/drivers/usb/host/uhci-hub.c
+++ usb-2.6/drivers/usb/host/uhci-hub.c
@@ -167,7 +167,7 @@ static void uhci_check_ports(struct uhci
/* Port received a wakeup request */
set_bit(port, &uhci->resuming_ports);
uhci->ports_timeout = jiffies +
- msecs_to_jiffies(20);
+ msecs_to_jiffies(25);
/* Make sure we see the port again
* after the resuming period is over. */
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
