On 22.10.2024 16.22, Mika Westerberg wrote:
Hi,
On Tue, Oct 22, 2024 at 03:37:42PM +0300, Mathias Nyman wrote:
Fix a boot hang issue triggered when a USB3 device is incorrectly assumed
to be tunneled over USB4, thus attempting to create a device link between
the USB3 "consumer" device and the USB4 "supplier" Host Interface before
the USB4 side is properly bound to a driver.
This could happen if xhci isn't capable of detecting tunneled devices,
but ACPI tables contain all info needed to assume device is tunneled.
i.e. udev->tunnel_mode == USB_LINK_UNKNOWN.
If the USB4 host interface hasn't probed yet, then we know the USB3
device is not in a tunnel created by the USB4 Host Interface driver, so
don't try to create a device link in this case.
cc: Mario Limonciello <mario.limonciello@xxxxxxx>
Fixes: f1bfb4a6fed6 ("usb: acpi: add device link between tunneled USB3 device and USB4 Host Interface")
Tested-by: Harry Wentland <harry.wentland@xxxxxxx>
Signed-off-by: Mathias Nyman <mathias.nyman@xxxxxxxxxxxxxxx>
---
drivers/usb/core/usb-acpi.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/drivers/usb/core/usb-acpi.c b/drivers/usb/core/usb-acpi.c
index 21585ed89ef8..9e1ec71881db 100644
--- a/drivers/usb/core/usb-acpi.c
+++ b/drivers/usb/core/usb-acpi.c
@@ -173,6 +173,17 @@ static int usb_acpi_add_usb4_devlink(struct usb_device *udev)
if (IS_ERR(nhi_fwnode))
return 0;
+ /*
+ * If USB4 Host interface driver isn't set up yet we can't be in a USB3
+ * tunnel created by it.
+ */
+ if (!nhi_fwnode->dev || !device_is_bound(nhi_fwnode->dev)) {
+ dev_info(&port_dev->dev, "%s probed before USB4 host interface\n",
+ dev_name(&port_dev->child->dev));
+ udev->tunnel_mode = USB_LINK_NATIVE;
+ return 0;
+ }
I think this will not work if you boot with "thunderbolt.host_reset=0"
and the BIOS CM created the tunnels, and that Thunderbolt/USB4 driver is
bound after xHCI. Then it will mark this as USB_LINK_NATIVE and does not
setup the link so after Thunderbolt/USB4 is runtime suspended it might
not be there to re-create the tunnel before xHCI.
The test case would be something like this:
1. Add "thunderbolt.host_reset=0" in the kernel command line.
2. Boot with USB4 device connected (and so that it has USB 3.x device
connected such as USB 3 memory stick).
3. Since there is no device link Thunderbolt/USB4 can runtime suspend
freely.
4. Once that happens the tunnels are gone, including the USB 3.x tunnel
so the xHCI might see disconnect here.
Also on resume path it will not be recreating the tunnel before xHCI
because there is no device link. I can try this on my side too if you
like.
You are right, I was able to reproduce it.
Device link won't be created if BIOS created the tunnel, thunderbolt driver
probes after this usb device is created, and "thunderbolt.host_reset=0" is set.
Turning the device link "stateless" could possible help.
It removes driver presence dependency but keeps correct suspend/resume and
shutdown ordering.
It should also help with boot hang/probe issues seen on the AMD platforms.
Mario, Harry, does the following work for you?
diff --git a/drivers/usb/core/usb-acpi.c b/drivers/usb/core/usb-acpi.c
index 21585ed89ef8..03c22114214b 100644
--- a/drivers/usb/core/usb-acpi.c
+++ b/drivers/usb/core/usb-acpi.c
@@ -170,11 +170,11 @@ static int usb_acpi_add_usb4_devlink(struct usb_device *udev)
struct fwnode_handle *nhi_fwnode __free(fwnode_handle) =
fwnode_find_reference(dev_fwnode(&port_dev->dev), "usb4-host-interface", 0);
- if (IS_ERR(nhi_fwnode))
+ if (IS_ERR(nhi_fwnode) || !nhi_fwnode->dev)
return 0;
link = device_link_add(&port_dev->child->dev, nhi_fwnode->dev,
- DL_FLAG_AUTOREMOVE_CONSUMER |
+ DL_FLAG_STATELESS |
DL_FLAG_RPM_ACTIVE |
DL_FLAG_PM_RUNTIME);
if (!link) {
Thanks
Mathias
