Fixed some confusing typos that were currently identified with codespell,
the details are as follows:
-in the code comments:
drivers/usb/dwc3/core.c:1406: feild ==> field
drivers/usb/dwc3/core.h:84: boundries ==> boundaries
drivers/usb/dwc3/ep0.c:148: issueing ==> issuing
drivers/usb/dwc3/host.c:38: temperary ==> temporary
Signed-off-by: Shen Lichuan <shenlichuan@xxxxxxxx>
---
drivers/usb/dwc3/core.c | 2 +-
drivers/usb/dwc3/core.h | 2 +-
drivers/usb/dwc3/ep0.c | 2 +-
drivers/usb/dwc3/host.c | 2 +-
4 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 9eb085f359ce..3612a57f7877 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -1403,7 +1403,7 @@ static int dwc3_core_init(struct dwc3 *dwc)
/*
* When configured in HOST mode, after issuing U3/L2 exit controller
- * fails to send proper CRC checksum in CRC5 feild. Because of this
+ * fails to send proper CRC checksum in CRC5 field. Because of this
* behaviour Transaction Error is generated, resulting in reset and
* re-enumeration of usb device attached. All the termsel, xcvrsel,
* opmode becomes 0 during end of resume. Enabling bit 10 of GUCTL1
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index c71240e8f7c7..2cb88e08e746 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -81,7 +81,7 @@
#define DWC3_GSNPSREV_MASK 0xffff
#define DWC3_GSNPS_ID(p) (((p) & DWC3_GSNPSID_MASK) >> 16)
-/* DWC3 registers memory space boundries */
+/* DWC3 registers memory space boundaries */
#define DWC3_XHCI_REGS_START 0x0
#define DWC3_XHCI_REGS_END 0x7fff
#define DWC3_GLOBALS_REGS_START 0xc100
diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
index c9533a99e47c..f3d97ad5156e 100644
--- a/drivers/usb/dwc3/ep0.c
+++ b/drivers/usb/dwc3/ep0.c
@@ -145,7 +145,7 @@ static int __dwc3_gadget_ep0_queue(struct dwc3_ep *dep,
* Unfortunately we have uncovered a limitation wrt the Data Phase.
*
* Section 9.4 says we can wait for the XferNotReady(DATA) event to
- * come before issueing Start Transfer command, but if we do, we will
+ * come before issuing Start Transfer command, but if we do, we will
* miss situations where the host starts another SETUP phase instead of
* the DATA phase. Such cases happen at least on TD.7.6 of the Link
* Layer Compliance Suite.
diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
index e0533cee6870..60f7a55e1ea3 100644
--- a/drivers/usb/dwc3/host.c
+++ b/drivers/usb/dwc3/host.c
@@ -35,7 +35,7 @@ static void dwc3_power_off_all_roothub_ports(struct dwc3 *dwc)
u32 reg;
int i;
- /* xhci regs is not mapped yet, do it temperary here */
+ /* xhci regs is not mapped yet, do it temporary here */
if (dwc->xhci_resources[0].start) {
xhci_regs = ioremap(dwc->xhci_resources[0].start, DWC3_XHCI_REGS_END);
if (!xhci_regs) {
--
2.17.1
