The current logic is rigid, setting num_fifos to fixed values.
3 for any maxburst greater than 1.
tx_fifo_resize_max_num for maxburst greater than 6.
Additionally, it did not differentiate much between bulk and
isochronous transfers, applying similar logic to both.
The updated logic is more flexible and specifically designed to meet
the unique requirements of both bulk and isochronous transfers. We
have made every effort to satisfy all needs and requirements,
verified on our specific platform and application.
The updated logic is more flexible and specifically designed to meet
the unique requirements of both bulk and isochronous transfers. We
have made every effort to satisfy all needs and requirements, verified
on our specific platform and application.
Bulk Transfers: Ensures that num_fifos is optimized by considering both
the maxburst and DT property tx_fifo_resize_max_num for super speed and
above. For high-speed and below bulk endpoints, a 2K TxFIFO allocation
is used to meet efficient data transfer needs, considering
FIFO-constrained platforms.
Isochronous Transfers: Ensures that num_fifos is sufficient by considering
the maximum packet multiplier for HS and maxburst for SS, along with a
constraint with the DT property tx_fifo_resize_max_num.
This change aims to optimize the allocation of Tx FIFOs for both bulk
and isochronous endpoints, potentially improving data transfer efficiency
and overall performance. It also enhances support for all use cases,
which can be tweaked with DT parameters and the endpoint’s maxburst and
maxpacket.
Signed-off-by: Akash Kumar <quic_akakum@xxxxxxxxxxx>
---
Changes for v5:
Update Calculation for HS and below bulk and isoc eps based on
suggestion and fixed at 2k for bulk eps considering fifo
constrained platforms.
Changes for v4:
Updated commit message as per review comments to clarify that it has
been tested on specific platforms only and tried best to match all
expectations.
Changes for v3:
Redefine logic for resizing tx fifos,added check based on operating
speed and used maxp for HS and maxburst for SS and defined max
allocation based on dt property.
Changes for v2:
Redefine logic for resizing tx fifos, handled fifo based on minimum
of maxp and maxburts.
Changes for v1:
Added additional condition to allocate tx fifo for hs isoc eps,
keeping the other resize logic same.
---
drivers/usb/dwc3/gadget.c | 20 +++++++++++++-------
1 file changed, 13 insertions(+), 7 deletions(-)
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 291bc549935b..035d49155d57 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -771,15 +771,21 @@ static int dwc3_gadget_resize_tx_fifos(struct dwc3_ep *dep)
ram1_depth = DWC3_RAM1_DEPTH(dwc->hwparams.hwparams7);
- if ((dep->endpoint.maxburst > 1 &&
- usb_endpoint_xfer_bulk(dep->endpoint.desc)) ||
- usb_endpoint_xfer_isoc(dep->endpoint.desc))
- num_fifos = 3;
+ if (dwc->gadget->speed <= USB_SPEED_HIGH) {
+ if (usb_endpoint_xfer_bulk(dep->endpoint.desc))
+ num_fifos = 2;
+ if (usb_endpoint_xfer_isoc(dep->endpoint.desc))
+ num_fifos = min_t(unsigned int,
+ usb_endpoint_maxp_mult(dep->endpoint.desc) + 1,
+ dwc->tx_fifo_resize_max_num);
+ }
- if (dep->endpoint.maxburst > 6 &&
+ if (dwc->gadget->speed > USB_SPEED_HIGH &&
(usb_endpoint_xfer_bulk(dep->endpoint.desc) ||
- usb_endpoint_xfer_isoc(dep->endpoint.desc)) && DWC3_IP_IS(DWC31))
- num_fifos = dwc->tx_fifo_resize_max_num;
+ usb_endpoint_xfer_isoc(dep->endpoint.desc)))
+ num_fifos = min_t(unsigned int,
+ dep->endpoint.maxburst,
+ dwc->tx_fifo_resize_max_num);
/* FIFO size for a single buffer */
fifo = dwc3_gadget_calc_tx_fifo_size(dwc, 1);
--
2.17.1
