Re: [PATCH v3 3/5] phy: fsl-imx8mq-usb: add tca function driver for imx95

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Aug 29, 2024 at 11:38:30PM +0530, Vinod Koul wrote:
> On 26-08-24, 15:08, Xu Yang wrote:
> > The i.MX95 USB3 phy has a Type-C Assist block (TCA). This block consists
> > two functional blocks (XBar assist and VBus assist) and one system
> > access interface using APB.
> > 
> > The primary functionality of XBar assist is:
> >  - switching lane for flip
> >  - moving unused lanes into lower power states.
> > 
> > This info can be get from:
> > i.MX95 RM Chapter 163.3.8 Type-C assist (TCA) block.
> > 
> > This will add support for TCA block to achieve lane switching and tca
> > lower power functionality.
> > 
> > Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx>
> > Reviewed-by: Jun Li <jun.li@xxxxxxx>
> > 
> > ---
> > Changes in v2:
> >  - return the value of imx95_usb_phy_get_tca()
> > Changes in v3:
> >  - no changes
> > ---
> >  drivers/phy/freescale/Kconfig              |   1 +
> >  drivers/phy/freescale/phy-fsl-imx8mq-usb.c | 240 +++++++++++++++++++++
> >  2 files changed, 241 insertions(+)
> > 
> > diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
> > index dcd9acff6d01..81f53564ee15 100644
> > --- a/drivers/phy/freescale/Kconfig
> > +++ b/drivers/phy/freescale/Kconfig
> > @@ -5,6 +5,7 @@ if (ARCH_MXC && ARM64) || COMPILE_TEST
> >  config PHY_FSL_IMX8MQ_USB
> >  	tristate "Freescale i.MX8M USB3 PHY"
> >  	depends on OF && HAS_IOMEM
> > +	depends on TYPEC || TYPEC=n
> >  	select GENERIC_PHY
> >  	default ARCH_MXC && ARM64
> >  
> > diff --git a/drivers/phy/freescale/phy-fsl-imx8mq-usb.c b/drivers/phy/freescale/phy-fsl-imx8mq-usb.c
> > index adc6394626ce..8bd6d91951a2 100644
> > --- a/drivers/phy/freescale/phy-fsl-imx8mq-usb.c
> > +++ b/drivers/phy/freescale/phy-fsl-imx8mq-usb.c
> > @@ -10,6 +10,7 @@
> >  #include <linux/phy/phy.h>
> >  #include <linux/platform_device.h>
> >  #include <linux/regulator/consumer.h>
> > +#include <linux/usb/typec_mux.h>
> >  
> >  #define PHY_CTRL0			0x0
> >  #define PHY_CTRL0_REF_SSP_EN		BIT(2)
> > @@ -50,11 +51,66 @@
> >  
> >  #define PHY_TUNE_DEFAULT		0xffffffff
> >  
> > +#define TCA_CLK_RST			0x00
> > +#define TCA_CLK_RST_SW			BIT(9)
> > +#define TCA_CLK_RST_REF_CLK_EN		BIT(1)
> > +#define TCA_CLK_RST_SUSPEND_CLK_EN	BIT(0)
> > +
> > +#define TCA_INTR_EN			0x04
> > +#define TCA_INTR_STS			0x08
> > +
> > +#define TCA_GCFG			0x10
> > +#define TCA_GCFG_ROLE_HSTDEV		BIT(4)
> > +#define TCA_GCFG_OP_MODE		GENMASK(1, 0)
> > +#define TCA_GCFG_OP_MODE_SYSMODE	0
> > +#define TCA_GCFG_OP_MODE_SYNCMODE	1
> > +
> > +#define TCA_TCPC			0x14
> > +#define TCA_TCPC_VALID			BIT(4)
> > +#define TCA_TCPC_LOW_POWER_EN		BIT(3)
> > +#define TCA_TCPC_ORIENTATION_NORMAL	BIT(2)
> > +#define TCA_TCPC_MUX_CONTRL		GENMASK(1, 0)
> > +#define TCA_TCPC_MUX_CONTRL_NO_CONN	0
> > +#define TCA_TCPC_MUX_CONTRL_USB_CONN	1
> > +
> > +#define TCA_SYSMODE_CFG			0x18
> > +#define TCA_SYSMODE_TCPC_DISABLE	BIT(3)
> > +#define TCA_SYSMODE_TCPC_FLIP		BIT(2)
> > +
> > +#define TCA_CTRLSYNCMODE_CFG0		0x20
> > +#define TCA_CTRLSYNCMODE_CFG1           0x20
> > +
> > +#define TCA_PSTATE			0x30
> > +#define TCA_PSTATE_CM_STS		BIT(4)
> > +#define TCA_PSTATE_TX_STS		BIT(3)
> > +#define TCA_PSTATE_RX_PLL_STS		BIT(2)
> > +#define TCA_PSTATE_PIPE0_POWER_DOWN	GENMASK(1, 0)
> > +
> > +#define TCA_GEN_STATUS			0x34
> > +#define TCA_GEN_DEV_POR			BIT(12)
> > +#define TCA_GEN_REF_CLK_SEL		BIT(8)
> > +#define TCA_GEN_TYPEC_FLIP_INVERT	BIT(4)
> > +#define TCA_GEN_PHY_TYPEC_DISABLE	BIT(3)
> > +#define TCA_GEN_PHY_TYPEC_FLIP		BIT(2)
> > +
> > +#define TCA_VBUS_CTRL			0x40
> > +#define TCA_VBUS_STATUS			0x44
> > +
> > +#define TCA_INFO			0xFC
> > +
> > +struct tca_blk {
> > +	struct typec_switch_dev *sw;
> > +	void __iomem *base;
> > +	struct mutex mutex;
> > +	enum typec_orientation orientation;
> > +};
> > +
> >  struct imx8mq_usb_phy {
> >  	struct phy *phy;
> >  	struct clk *clk;
> >  	void __iomem *base;
> >  	struct regulator *vbus;
> > +	struct tca_blk *tca;
> >  	u32 pcs_tx_swing_full;
> >  	u32 pcs_tx_deemph_3p5db;
> >  	u32 tx_vref_tune;
> > @@ -64,6 +120,170 @@ struct imx8mq_usb_phy {
> >  	u32 comp_dis_tune;
> >  };
> >  
> > +
> > +static void tca_blk_orientation_set(struct tca_blk *tca,
> > +				enum typec_orientation orientation);
> > +
> > +#ifdef CONFIG_TYPEC
> > +
> > +static int tca_blk_typec_switch_set(struct typec_switch_dev *sw,
> > +				enum typec_orientation orientation)
> > +{
> > +	struct imx8mq_usb_phy *imx_phy = typec_switch_get_drvdata(sw);
> > +	struct tca_blk *tca = imx_phy->tca;
> > +	int ret;
> > +
> > +	if (tca->orientation == orientation)
> > +		return 0;
> > +
> > +	ret = clk_prepare_enable(imx_phy->clk);
> > +	if (ret)
> > +		return ret;
> > +
> > +	tca_blk_orientation_set(tca, orientation);
> > +	clk_disable_unprepare(imx_phy->clk);
> > +
> > +	return 0;
> > +}
> > +
> > +static struct typec_switch_dev *tca_blk_get_typec_switch(struct platform_device *pdev,
> > +					struct imx8mq_usb_phy *imx_phy)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct typec_switch_dev *sw;
> > +	struct typec_switch_desc sw_desc = { };
> > +
> > +	sw_desc.drvdata = imx_phy;
> > +	sw_desc.fwnode = dev->fwnode;
> > +	sw_desc.set = tca_blk_typec_switch_set;
> > +	sw_desc.name = NULL;
> > +
> > +	sw = typec_switch_register(dev, &sw_desc);
> > +	if (IS_ERR(sw)) {
> > +		dev_err(dev, "Error register tca orientation switch: %ld",
> > +				PTR_ERR(sw));
> > +		return NULL;
> > +	}
> > +
> > +	return sw;
> > +}
> > +
> > +static void tca_blk_put_typec_switch(struct typec_switch_dev *sw)
> > +{
> > +	typec_switch_unregister(sw);
> > +}
> > +
> > +#else
> > +
> > +static struct typec_switch_dev *tca_blk_get_typec_switch(struct platform_device *pdev,
> > +			struct imx8mq_usb_phy *imx_phy)
> > +{
> > +	return NULL;
> > +}
> > +
> > +static void tca_blk_put_typec_switch(struct typec_switch_dev *sw) {}
> > +
> > +#endif /* CONFIG_TYPEC */
> > +
> > +static void tca_blk_orientation_set(struct tca_blk *tca,
> > +				enum typec_orientation orientation)
> > +{
> > +	u32 val;
> > +
> > +	mutex_lock(&tca->mutex);
> > +
> > +	if (orientation == TYPEC_ORIENTATION_NONE) {
> > +		/*
> > +		 * use Controller Synced Mode for TCA low power enable and
> > +		 * put PHY to USB safe state.
> > +		 */
> > +		val = readl(tca->base + TCA_GCFG);
> > +		val = FIELD_PREP(TCA_GCFG_OP_MODE, TCA_GCFG_OP_MODE_SYNCMODE);
> > +		writel(val, tca->base + TCA_GCFG);
> > +
> > +		val = readl(tca->base + TCA_TCPC);
> > +		val = TCA_TCPC_VALID | TCA_TCPC_LOW_POWER_EN;
> > +		writel(val, tca->base + TCA_TCPC);
> > +
> > +		goto out;
> > +	}
> > +
> > +	/* use System Configuration Mode for TCA mux control. */
> > +	val = readl(tca->base + TCA_GCFG);
> > +	val = FIELD_PREP(TCA_GCFG_OP_MODE, TCA_GCFG_OP_MODE_SYSMODE);
> > +	writel(val, tca->base + TCA_GCFG);
> > +
> > +	/* Disable TCA module */
> > +	val = readl(tca->base + TCA_SYSMODE_CFG);
> > +	val |= TCA_SYSMODE_TCPC_DISABLE;
> > +	writel(val, tca->base + TCA_SYSMODE_CFG);
> > +
> > +	if (orientation == TYPEC_ORIENTATION_REVERSE)
> > +		val |= TCA_SYSMODE_TCPC_FLIP;
> > +	else if (orientation == TYPEC_ORIENTATION_NORMAL)
> > +		val &= ~TCA_SYSMODE_TCPC_FLIP;
> > +
> > +	writel(val, tca->base + TCA_SYSMODE_CFG);
> > +
> > +	/* Enable TCA module */
> > +	val &= ~TCA_SYSMODE_TCPC_DISABLE;
> > +	writel(val, tca->base + TCA_SYSMODE_CFG);
> > +
> > +out:
> > +	tca->orientation = orientation;
> > +	mutex_unlock(&tca->mutex);
> > +}
> > +
> > +static void tca_blk_init(struct tca_blk *tca)
> > +{
> > +	u32 val;
> > +
> > +	/* reset XBar block */
> > +	val = readl(tca->base + TCA_CLK_RST);
> > +	val &= ~TCA_CLK_RST_SW;
> > +	writel(val, tca->base + TCA_CLK_RST);
> > +
> > +	udelay(100);
> > +
> > +	/* clear reset */
> > +	val |= TCA_CLK_RST_SW;
> > +	writel(val, tca->base + TCA_CLK_RST);
> > +
> > +	tca_blk_orientation_set(tca, tca->orientation);
> > +}
> > +
> > +static struct tca_blk *imx95_usb_phy_get_tca(struct platform_device *pdev,
> > +				struct imx8mq_usb_phy *imx_phy)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct tca_blk *tca;
> > +
> > +	tca = devm_kzalloc(dev, sizeof(*tca), GFP_KERNEL);
> > +	if (!tca)
> > +		return ERR_PTR(-ENOMEM);
> > +
> > +	tca->base = devm_platform_ioremap_resource(pdev, 1);
> > +	if (IS_ERR(tca->base))
> > +		return tca->base;
> > +
> > +	mutex_init(&tca->mutex);
> > +
> > +	tca->orientation = TYPEC_ORIENTATION_NORMAL;
> > +	tca->sw = tca_blk_get_typec_switch(pdev, imx_phy);
> > +
> > +	return tca;
> > +}
> > +
> > +static void imx95_usb_phy_put_tca(struct imx8mq_usb_phy *imx_phy)
> > +{
> > +	struct tca_blk *tca = imx_phy->tca;
> > +
> > +	if (!tca)
> > +		return;
> > +
> > +	tca_blk_put_typec_switch(tca->sw);
> > +}
> > +
> >  static u32 phy_tx_vref_tune_from_property(u32 percent)
> >  {
> >  	percent = clamp(percent, 94U, 124U);
> > @@ -315,6 +535,9 @@ static int imx8mp_usb_phy_init(struct phy *phy)
> >  
> >  	imx8m_phy_tune(imx_phy);
> >  
> > +	if (imx_phy->tca)
> > +		tca_blk_init(imx_phy->tca);
> > +
> >  	return 0;
> >  }
> >  
> > @@ -359,6 +582,8 @@ static const struct of_device_id imx8mq_usb_phy_of_match[] = {
> >  	 .data = &imx8mq_usb_phy_ops,},
> >  	{.compatible = "fsl,imx8mp-usb-phy",
> >  	 .data = &imx8mp_usb_phy_ops,},
> > +	{.compatible = "fsl,imx95-usb-phy",
> > +	 .data = &imx8mp_usb_phy_ops,},
> 
> Okay
> 
> >  	{ }
> >  };
> >  MODULE_DEVICE_TABLE(of, imx8mq_usb_phy_of_match);
> > @@ -398,6 +623,13 @@ static int imx8mq_usb_phy_probe(struct platform_device *pdev)
> >  
> >  	phy_set_drvdata(imx_phy->phy, imx_phy);
> >  
> > +	if (device_is_compatible(dev, "fsl,imx95-usb-phy")) {
> 
> so future version will also have this check, so are we going to increase
> this..? maybe better idea is to expand imx8mp_usb_phy_ops and add a flag
> for tca support and set that for required compatible, or make this a
> property?

Ok. It seems like a potential issue. Your advice sounds good. Will try it.

Thanks,
Xu Yang

> 
> 
> > +		imx_phy->tca = imx95_usb_phy_get_tca(pdev, imx_phy);
> > +		if (IS_ERR(imx_phy->tca))
> > +			return dev_err_probe(dev, PTR_ERR(imx_phy->tca),
> > +						"failed to get tca\n");
> > +	}
> > +
> >  	imx8m_get_phy_tuning_data(imx_phy);
> >  
> >  	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> > @@ -405,8 +637,16 @@ static int imx8mq_usb_phy_probe(struct platform_device *pdev)
> >  	return PTR_ERR_OR_ZERO(phy_provider);
> >  }
> >  
> > +static void imx8mq_usb_phy_remove(struct platform_device *pdev)
> > +{
> > +	struct imx8mq_usb_phy *imx_phy = platform_get_drvdata(pdev);
> > +
> > +	imx95_usb_phy_put_tca(imx_phy);
> > +}
> > +
> >  static struct platform_driver imx8mq_usb_phy_driver = {
> >  	.probe	= imx8mq_usb_phy_probe,
> > +	.remove = imx8mq_usb_phy_remove,
> >  	.driver = {
> >  		.name	= "imx8mq-usb-phy",
> >  		.of_match_table	= imx8mq_usb_phy_of_match,
> > -- 
> > 2.34.1
> 
> -- 
> ~Vinod




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux