RE: [PATCH 00/16] Add initial USB support for the Renesas RZ/G3S SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Claudiu,

> -----Original Message-----
> From: Biju Das
> Sent: Saturday, August 31, 2024 6:14 AM
> Subject: RE: [PATCH 00/16] Add initial USB support for the Renesas RZ/G3S SoC
> 
> Hi Claudiu,
> 
> > -----Original Message-----
> > From: claudiu beznea <claudiu.beznea@xxxxxxxxx>
> > Sent: Friday, August 30, 2024 9:23 AM
> > Subject: Re: [PATCH 00/16] Add initial USB support for the Renesas
> > RZ/G3S SoC
> >
> > Hi, Ulf,
> >
> > On 29.08.2024 18:26, Ulf Hansson wrote:
> > > On Thu, 22 Aug 2024 at 17:28, Claudiu <claudiu.beznea@xxxxxxxxx> wrote:
> > >>
> > >> From: Claudiu Beznea <claudiu.beznea.uj@xxxxxxxxxxxxxx>
> > >>
> > >> Hi,
> > >>
> > >> Series adds initial USB support for the Renesas RZ/G3S SoC.
> > >>
> > >> Series is split as follows:
> > >>
> > >> - patch 01/16           - add clock reset and power domain support for USB
> > >> - patch 02-04/16        - add reset control support for a USB signal
> > >>                           that need to be controlled before/after
> > >>                           the power to USB area is turned on/off.
> > >>
> > >>                           Philipp, Ulf, Geert, all,
> > >>
> > >>                           I detailed my approach for this in patch
> > >>                           04/16, please have a look and let me know
> > >>                           your input.
> > >
> > > I have looked briefly. Your suggested approach may work, but I have
> > > a few thoughts, see below.
> > >
> > > If I understand correctly, it is the consumer driver for the device
> > > that is attached to the USB power domain that becomes responsible
> > > for asserting/de-asserting this new signal. Right?
> >
> > Right!
> >
> > >
> > > In this regard, please note that the consumer driver doesn't really
> > > know when the power domain really gets powered-on/off. Calling
> > > pm_runtime_get|put*() is dealing with the reference counting. For
> > > example, a call to pm_runtime_get*() just makes sure that the PM
> > > domain gets-or-remains powered-on. Could this be a problem from the
> > > reset-signal point of view?
> >
> > It should be safe. From the HW manual I understand the hardware block is something like the
> following:
> >
> >
> >                   USB area
> >          +-------------------------+
> >          |                         |
> >          | PHY --->USB controller  |
> > SYSC --> |  ^                      |
> >          |  |                      |
> >          | PHY reset               |
> >          +-------------------------+
> 
> How USB PWRRDY signal is connected to USB?
> 
> USB block consists of PHY control, PHY, USB HOST and USB OTG Controller IPs.
> 
> Is it connected to top level block or connected to each IP's for turning off the USB region power?
> 
> ? Or Just PHY (HW manual mentions for AWO, the USB PWRRDY signal->USB PHY PWRRDY signal control)?

As per the update from HW team,

"SYS_USB_PWRRDY and SYS_PCIE_RST_RSM_B are used when transition from ALL_ON to AWO (or from AWO to ALL_ON).

Refer to step 8,9 in Table 41.10 Example Transition Flow Outline from ALL_ON Mode to AWO Mode.
Refer to step 9,10 in Table 41.11 Example Transition Flow Outline from AWO Mode to ALL_ON Mode.

When turning off USB PHY and PCIe PHY, if they are not controlled, PHY may break."

Do you have any plan to control this power transitions(ALL_ON to AWO and vice versa) in linux? 

Cheers,
Biju
 




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux