When operating in High-Speed, it is observed that DSTS[USBLNKST] doesn't
update link state immediately after receiving the wakeup interrupt. Since
wakeup event handler calls the resume callbacks, there is a chance that
function drivers can perform an ep queue, which in turn tries to perform
remote wakeup from send_gadget_ep_cmd(STARTXFER). This happens because
DSTS[[21:18] wasn't updated to U0 yet, it's observed that the latency of
DSTS can be in order of milli-seconds. Hence avoid calling gadget_wakeup
during startxfer to prevent unnecessarily issuing remote wakeup to host.
Fixes: c36d8e947a56 ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@xxxxxxxxxxxxxxx>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx>
Signed-off-by: Prashanth K <quic_prashk@xxxxxxxxxxx>
---
v5: Further rewording of the comment in function.
v4: Rewording the comment in function definition.
v3: Added notes on top the function definition.
v2: Refactored the patch as suggested in v1 discussion.
drivers/usb/dwc3/gadget.c | 41 ++++++++++++++++-----------------------
1 file changed, 17 insertions(+), 24 deletions(-)
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 89fc690fdf34..291bc549935b 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -287,6 +287,23 @@ static int __dwc3_gadget_wakeup(struct dwc3 *dwc, bool async);
*
* Caller should handle locking. This function will issue @cmd with given
* @params to @dep and wait for its completion.
+ *
+ * According to the programming guide, if the link state is in L1/L2/U3,
+ * then sending the Start Transfer command may not complete. The
+ * programming guide suggested to bring the link state back to ON/U0 by
+ * performing remote wakeup prior to sending the command. However, don't
+ * initiate remote wakeup when the user/function does not send wakeup
+ * request via wakeup ops. Send the command when it's allowed.
+ *
+ * Notes:
+ * For L1 link state, issuing a command requires the clearing of
+ * GUSB2PHYCFG.SUSPENDUSB2, which turns on the signal required to complete
+ * the given command (usually within 50us). This should happen within the
+ * command timeout set by driver. No additional step is needed.
+ *
+ * For L2 or U3 link state, the gadget is in USB suspend. Care should be
+ * taken when sending Start Transfer command to ensure that it's done after
+ * USB resume.
*/
int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
struct dwc3_gadget_ep_cmd_params *params)
@@ -327,30 +344,6 @@ int dwc3_send_gadget_ep_cmd(struct dwc3_ep *dep, unsigned int cmd,
dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg);
}
- if (DWC3_DEPCMD_CMD(cmd) == DWC3_DEPCMD_STARTTRANSFER) {
- int link_state;
-
- /*
- * Initiate remote wakeup if the link state is in U3 when
- * operating in SS/SSP or L1/L2 when operating in HS/FS. If the
- * link state is in U1/U2, no remote wakeup is needed. The Start
- * Transfer command will initiate the link recovery.
- */
- link_state = dwc3_gadget_get_link_state(dwc);
- switch (link_state) {
- case DWC3_LINK_STATE_U2:
- if (dwc->gadget->speed >= USB_SPEED_SUPER)
- break;
-
- fallthrough;
- case DWC3_LINK_STATE_U3:
- ret = __dwc3_gadget_wakeup(dwc, false);
- dev_WARN_ONCE(dwc->dev, ret, "wakeup failed --> %d\n",
- ret);
- break;
- }
- }
-
/*
* For some commands such as Update Transfer command, DEPCMDPARn
* registers are reserved. Since the driver often sends Update Transfer
--
2.25.1
