Re: [PATCH 5/6] usb: phy: mxs: enable weak 1p1 regulator for imx6ul during suspend

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Jul 18, 2024 at 06:26:36PM +0800, Xu Yang wrote:
> For imx6ul PHY, when the system enters suspend, its 1p1 is off by default,
> that may cause the PHY get inaccurate USB DP/DM value. If the USB wakeup
> is enabled at this time, the unexpected wakeup may occur when the system
> enters suspend.

1p1 is off when the system enters suspend at iMX6UL. It cause the PHY get
wrong USB DP/DM value, then unexpected wakeup may occur if USB wakeup
enabled. 

> 
> In this patch, when the vbus is there, we enable weak 1p1 during the PHY
> suspend API, in that case, the USB DP/DM will be accurate for USB PHY,
> then unexpected usb wakeup will not be occurred, especially for the USB
> charger is connected scenario. The user needs to enable PHY wakeup for
> USB wakeup function using below setting.

Avoid use word "this patch", "this commit."

Enable weak 1p1 during PHY suspend if vbus exist. So USB DP/DM is correct
when system suspend.

Reproduce step:
> 
> echo enabled > /sys/devices/platform/soc/2000000.aips-bus/20c9000.usbphy
> /power/wakeup

echo mem > /sys/power/state,


then some error happen. 

Or just remove it.

> 
> Signed-off-by: Xu Yang <xu.yang_2@xxxxxxx>
> ---
>  drivers/usb/phy/phy-mxs-usb.c | 32 ++++++++++++++++++++++++++++----
>  1 file changed, 28 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/usb/phy/phy-mxs-usb.c b/drivers/usb/phy/phy-mxs-usb.c
> index 627733a982d1..dcd032678814 100644
> --- a/drivers/usb/phy/phy-mxs-usb.c
> +++ b/drivers/usb/phy/phy-mxs-usb.c
> @@ -71,6 +71,9 @@
>  #define BM_USBPHY_PLL_EN_USB_CLKS		BIT(6)
>  
>  /* Anatop Registers */
> +#define ANADIG_REG_1P1_SET			0x114
> +#define ANADIG_REG_1P1_CLR			0x118
> +
>  #define ANADIG_ANA_MISC0			0x150
>  #define ANADIG_ANA_MISC0_SET			0x154
>  #define ANADIG_ANA_MISC0_CLR			0x158
> @@ -123,6 +126,9 @@
>  
>  #define USB_PHY_VLLS_WAKEUP_EN			BIT(0)
>  
> +#define BM_ANADIG_REG_1P1_ENABLE_WEAK_LINREG	BIT(18)
> +#define BM_ANADIG_REG_1P1_TRACK_VDD_SOC_CAP	BIT(19)
> +
>  #define to_mxs_phy(p) container_of((p), struct mxs_phy, phy)
>  
>  /* Do disconnection between PHY and controller without vbus */
> @@ -197,7 +203,8 @@ static const struct mxs_phy_data imx6sx_phy_data = {
>  };
>  
>  static const struct mxs_phy_data imx6ul_phy_data = {
> -	.flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS,
> +	.flags = MXS_PHY_DISCONNECT_LINE_WITHOUT_VBUS |
> +		MXS_PHY_HARDWARE_CONTROL_PHY2_CLK,
>  };
>  
>  static const struct mxs_phy_data imx7ulp_phy_data = {
> @@ -243,6 +250,11 @@ static inline bool is_imx7ulp_phy(struct mxs_phy *mxs_phy)
>  	return mxs_phy->data == &imx7ulp_phy_data;
>  }
>  
> +static inline bool is_imx6ul_phy(struct mxs_phy *mxs_phy)
> +{
> +	return mxs_phy->data == &imx6ul_phy_data;

You'd better define,  MXS_PHY_POWER_OFF_AT_SUSPEND. 

	is_phy_power_off_at_suspend(). 

Actually, you just need know if phy power off instead if it is 6ul phy.

> +}
> +
>  /*
>   * PHY needs some 32K cycles to switch from 32K clock to
>   * bus (such as AHB/AXI, etc) clock.
> @@ -891,18 +903,30 @@ static void mxs_phy_wakeup_enable(struct mxs_phy *mxs_phy, bool on)
>  
>  static void mxs_phy_enable_ldo_in_suspend(struct mxs_phy *mxs_phy, bool on)
>  {
> -	unsigned int reg = on ? ANADIG_ANA_MISC0_SET : ANADIG_ANA_MISC0_CLR;
> +	unsigned int reg;
> +	u32 value;
>  
>  	/* If the SoCs don't have anatop, quit */
>  	if (!mxs_phy->regmap_anatop)
>  		return;
>  
> -	if (is_imx6q_phy(mxs_phy))
> +	if (is_imx6q_phy(mxs_phy)) {
> +		reg = on ? ANADIG_ANA_MISC0_SET : ANADIG_ANA_MISC0_CLR;
>  		regmap_write(mxs_phy->regmap_anatop, reg,
>  			BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG);
> -	else if (is_imx6sl_phy(mxs_phy))
> +	} else if (is_imx6sl_phy(mxs_phy)) {
> +		reg = on ? ANADIG_ANA_MISC0_SET : ANADIG_ANA_MISC0_CLR;
>  		regmap_write(mxs_phy->regmap_anatop,
>  			reg, BM_ANADIG_ANA_MISC0_STOP_MODE_CONFIG_SL);
> +	} else if (is_imx6ul_phy(mxs_phy)) {
> +		reg = on ? ANADIG_REG_1P1_SET : ANADIG_REG_1P1_CLR;
> +		value = BM_ANADIG_REG_1P1_ENABLE_WEAK_LINREG |
> +			BM_ANADIG_REG_1P1_TRACK_VDD_SOC_CAP;
> +		if (mxs_phy_get_vbus_status(mxs_phy) && on)
> +			regmap_write(mxs_phy->regmap_anatop, reg, value);
> +		else if (!on)
> +			regmap_write(mxs_phy->regmap_anatop, reg, value);
> +	}
>  }
>  
>  static int mxs_phy_system_suspend(struct device *dev)
> -- 
> 2.34.1
> 




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux