The interface between UCSI and the glue driver is very low-level. It allows reading the UCSI data from any offset (but in reality the UCSI driver reads only VERSION, CCI an MESSAGE_IN data). All event handling is to be done by the glue driver (which already resulted in several similar-but-slightly different implementations). It leaves no place to optimize the write-read-read sequence for the command execution (which might be beneficial for some of the drivers), etc. The patchseries attempts to restructure the UCSI glue driver interface in order to provide sensible operations instead of a low-level read / write calls. If this approach is found to be acceptable, I plan to further rework the command interface, moving reading CCI and MESSAGE_IN to the common control code, which should simplify driver's implementation and remove necessity to split quirks between sync_control and read_message_in e.g. as implemented in the ucsi_ccg.c. Note, the series was tested only on the ucsi_glink platforms. Further testing is appreciated. Depends: [1], [2] [1] https://lore.kernel.org/linux-usb/20240612124656.2305603-1-fabrice.gasnier@xxxxxxxxxxx/ [2] https://lore.kernel.org/linux-usb/20240621-ucsi-yoga-ec-driver-v8-1-e03f3536b8c6@xxxxxxxxxx/ Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx> --- Changes in v4: - Rebased on top of Greg's tree to resolve conflicts. - Link to v3: https://lore.kernel.org/r/20240625-ucsi-rework-interface-v3-0-7a6c8e17be3a@xxxxxxxxxx Changes in v3: - Rebased on top of the next to resolve conflicts with the merge LG Gram patch (Heikki) - Link to v2: https://lore.kernel.org/r/20240621-ucsi-rework-interface-v2-0-a399ff96bf88@xxxxxxxxxx Changes in v2: - Dropped the RFC prefix - Rebased on top of the fixed STM32 patch - Included the pending Yoga C630 driver into the cleanup. - Link to v1: https://lore.kernel.org/r/20240603-ucsi-rework-interface-v1-0-99a6d544cec8@xxxxxxxxxx --- Dmitry Baryshkov (7): usb: typec: ucsi: move ucsi_acknowledge() from ucsi_read_error() usb: typec: ucsi: simplify command sending API usb: typec: ucsi: split read operation usb: typec: ucsi: rework command execution functions usb: typec: ucsi: inline ucsi_read_message_in usb: typec: ucsi: extract common code for command handling usb: typec: ucsi: reorder operations in ucsi_run_command() drivers/usb/typec/ucsi/ucsi.c | 221 +++++++++++++++++--------------- drivers/usb/typec/ucsi/ucsi.h | 26 ++-- drivers/usb/typec/ucsi/ucsi_acpi.c | 127 +++++++++--------- drivers/usb/typec/ucsi/ucsi_ccg.c | 103 +++++++-------- drivers/usb/typec/ucsi/ucsi_glink.c | 74 ++++------- drivers/usb/typec/ucsi/ucsi_stm32g0.c | 79 ++++-------- drivers/usb/typec/ucsi/ucsi_yoga_c630.c | 104 +++++---------- 7 files changed, 325 insertions(+), 409 deletions(-) --- base-commit: 878bae2ba39bdd581cbe77d8210b9a03ae172adf change-id: 20240525-ucsi-rework-interface-5ff2264f6aec Best regards, -- Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
