On Sat, 30 Mar 2024 at 11:13, Krishna Kurapati PSSNV
<quic_kriskura@xxxxxxxxxxx> wrote:
> On 3/29/2024 6:23 PM, Dmitry Baryshkov wrote:
> > On Fri, 29 Mar 2024 at 09:20, Krishna Kurapati
> > <quic_kriskura@xxxxxxxxxxx> wrote:
> >>
> >> QDU1000 IDP [1] has a Type-c connector and supports USB 3.0.
> >> However it relies on usb-conn-gpio driver to read the vbus and id
> >> gpio's and provide role switch. However the driver currently has
> >> only gpio-b-connector compatible present in ID table. Adding that
> >> in DT would mean that the device supports Type-B connector and not
> >> Type-c connector. Thanks to Dmitry Baryshkov for pointing it out [2].
> >
> > USB-B connector is pretty simple, it really has just an ID pin and
> > VBUS input, which translates to two GPIOs being routed from the
> > _connector_ itself.
> >
> > USB-C is much more complicated, it has two CC pins and a VBus power
> > pin. It is not enough just to measure CC pin levels. Moreover,
> > properly handling USB 3.0 inside a USB-C connector requires a separate
> > 'orientation' signal to tell the host which two lanes must be used for
> > the USB SS signals. Thus it is no longer possible to route just two
> > pins from the connector to the SoC.
> >
> > Having all that in mind, I suspect that you are not describing your
> > hardware properly. I suppose that you have a Type-C port controller /
> > redriver / switch, which handles CC lines communication and then
> > provides ID / VBUS signals to the host. In such a case, please
> > describe this TCPC in the DT file and use its compatible string
> > instead of "gpio-c-connector".
> >
>
> Hi Dmitry,
>
> My bad. I must have provided more details of the HW.
>
> I presume you are referring to addition of a connector node, type-c
> switch, pmic-glink and other remote endpoints like in other SoC's like
> SM8450/ SM8550/ SM8650.
>
> This HW is slightly different. It has a Uni Phy for Super speed and
> hence no DP.
This is fine and it's irrelevant for the USB-C.
> For orientation switching, on mobile SoC's, there is a provision for
> orientation gpio given in pmic-glink node and is handled in ucsi_glink
> driver. But on this version of HW, there is a USB-C Switch with its own
> firmware taking care of orientation switching. It takes 8 SS Lines and 2
> CC lines coming from connector as input and gives out 4 SS Lines (SS
> TX1/TX2 RX1/RX2) as output which go to the SoC. So orientation switch is
> done by the USB-C-switch in between and it automatically routes
> appropriate active SS Lane from connector to the SoC.
This is also fine. As I wrote, you _have_ the Type-C port controller.
So your DT file should be describing your hardware.
> As usual like in other targets, the DP and DM lines from type-c
> connector go to the SoC directly.
>
> To handle role switch, the VBUS and ID Pin connections are given to
> SoC as well. There is a vbus controller regulator present to provide
> vbus to connected peripherals in host mode.
>
> There is no PPM entity (ADSP in mobile SoC's) and no UCSI involved
> here. Hence we rely on usb-conn-gpio to read the vbus/id and switch
> roles accordingly.
This is also fine.
You confirmed my suspicions. You have an external Type-C switch which
handles orientation (and most likely PD or non-PD power negotiation)
for you. It has GPIO outputs, etc.
But it is not a part of the connector. Instead of adding the
"gpio-usb-c-connector", add proper compatible string (see, how this is
handled e.g. by the spidev - it is a generic driver, but it requires
hardware-specific compatibles).
Your hardware description should look like:
typec {
compatible = "your,switch";
id-gpios = <&gpio 1>;
vbus-gpios = <&gpio 2>;
vbus-supplies = <®-vbus>;
ports {
#address-cells = <1>;
#size-cells = <1>;
port@0 {
endpoint {
remote-endpoint = <&usb_dwc3_hs_out>;
};
};
port@1 {
endpoint {
remote-endpoint = <&usb_uni_phy_out>;
};
};
/* No SBU port */
};
};
Note, I haven't said anything regarding the driver. You can continue
using the usb-conn-gpio driver. Just add a compatible string for you
switch.
>
> Hope this answers the query as to why we wanted to use usb-conn-gpio
> and why we were trying to add a new compatible.
>
> Regards,
> Krishna,
>
> >>
> >> This series intends to add that compatible in driver and bindings
> >> so that it can be used in QDU1000 IDP DT.
> >>
> >> [1]: https://lore.kernel.org/all/20240319091020.15137-3-quic_kbajaj@xxxxxxxxxxx/
> >> [2]: https://lore.kernel.org/all/CAA8EJprXPvji8TgZu1idH7y4GtHtD4VmQABFBcRt-9BQaCberg@xxxxxxxxxxxxxx/
> >>
> >> Krishna Kurapati (2):
> >> dt-bindings: connector: Add gpio-usb-c-connector compatible
> >> usb: common: usb-conn-gpio: Update ID table to add usb-c connector
> >>
> >> Documentation/devicetree/bindings/connector/usb-connector.yaml | 3 +++
> >> drivers/usb/common/usb-conn-gpio.c | 1 +
> >> 2 files changed, 4 insertions(+)
> >>
> >> --
> >> 2.34.1
> >>
> >
> >
> > --
> > With best wishes
> > Dmitry
--
With best wishes
Dmitry
