On Tue, Mar 05, 2024 at 02:51:38PM +0800, Kai-Heng Feng wrote: > SanDisks USB3 storage may disapper after system reboot: > > usb usb2-port3: link state change > xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 > usb usb2-port3: do warm reset, port only > xhci_hcd 0000:00:14.0: xhci_hub_status_data: stopping usb2 port polling > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2b0, return 0x2b0 > usb usb2-port3: not warm reset yet, waiting 50ms > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2f0, return 0x2f0 > usb usb2-port3: not warm reset yet, waiting 200ms > ... > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x6802c0, return 0x7002c0 > usb usb2-port3: not warm reset yet, waiting 200ms > xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x4802c0 > xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x4002c0 > xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x2c0 > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x2c0, return 0x2c0 > usb usb2-port3: not enabled, trying warm reset again... > > This is due to the USB device still cause port change event after xHCI is > shuted down: > > xhci_hcd 0000:38:00.0: // Setting command ring address to 0xffffe001 > xhci_hcd 0000:38:00.0: xhci_resume: starting usb3 port polling. > xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb4 port polling > xhci_hcd 0000:38:00.0: xhci_hub_status_data: stopping usb3 port polling > xhci_hcd 0000:38:00.0: hcd_pci_runtime_resume: 0 > xhci_hcd 0000:38:00.0: xhci_shutdown: stopping usb3 port polling. > xhci_hcd 0000:38:00.0: // Halt the HC > xhci_hcd 0000:38:00.0: xhci_shutdown completed - status = 1 > xhci_hcd 0000:00:14.0: xhci_shutdown: stopping usb1 port polling. > xhci_hcd 0000:00:14.0: // Halt the HC > xhci_hcd 0000:00:14.0: xhci_shutdown completed - status = 1 > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 > xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1311 > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x201203, return 0x100203 > xhci_hcd 0000:00:14.0: clear port3 reset change, portsc: 0x1203 > xhci_hcd 0000:00:14.0: clear port3 warm(BH) reset change, portsc: 0x1203 > xhci_hcd 0000:00:14.0: clear port3 link state change, portsc: 0x1203 > xhci_hcd 0000:00:14.0: clear port3 connect change, portsc: 0x1203 > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1203, return 0x203 > usb 2-3: device not accepting address 2, error -108 > xhci_hcd 0000:00:14.0: xHCI dying or halted, can't queue_command > xhci_hcd 0000:00:14.0: Set port 2-3 link state, portsc: 0x1203, write 0x11261 > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x1263, return 0x263 > xhci_hcd 0000:00:14.0: set port reset, actual port 2-3 status = 0x1271 > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12b1, return 0x2b1 > usb usb2-port3: not reset yet, waiting 60ms > ACPI: PM: Preparing to enter system sleep state S5 > xhci_hcd 0000:00:14.0: Get port status 2-3 read: 0x12f1, return 0x2f1 > usb usb2-port3: not reset yet, waiting 200ms > reboot: Restarting system > > The port change event is caused by LPM transition, so disabling LPM at shutdown > to make sure the device is in U0 for warmboot. > > Signed-off-by: Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx> > --- > drivers/usb/core/port.c | 4 +++- > 1 file changed, 3 insertions(+), 1 deletion(-) What commit id does this fix?
