On Fri, 09 Feb 2024 23:09:14 -0800, Stephen Boyd wrote: > Add a graph with 4 output endpoints to this hub binding to support the > scenario where a downstream facing port is connected to a device that > isn't a connector or a USB device with a VID:PID. This will be used to > connect downstream facing ports to USB type-c switches so the USB > superspeed and high speed lanes can be put onto USB connectors. > > Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> > Cc: Rob Herring <robh+dt@xxxxxxxxxx> > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx> > Cc: Conor Dooley <conor+dt@xxxxxxxxxx> > Cc: Matthias Kaehlcke <mka@xxxxxxxxxxxx> > Cc: <linux-usb@xxxxxxxxxxxxxxx> > Cc: <devicetree@xxxxxxxxxxxxxxx> > Cc: Pin-yen Lin <treapking@xxxxxxxxxxxx> > Cc: maciek swiech <drmasquatch@xxxxxxxxxx> > Signed-off-by: Stephen Boyd <swboyd@xxxxxxxxxxxx> > --- > .../bindings/usb/realtek,rts5411.yaml | 50 +++++++++++++++++++ > 1 file changed, 50 insertions(+) > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: Documentation/devicetree/bindings/usb/realtek,rts5411.example.dts:32.21-31: Warning (reg_format): /example-0/usb/hub@1/device@2:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb: Warning (pci_device_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb: Warning (simple_bus_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format' Documentation/devicetree/bindings/usb/realtek,rts5411.example.dts:30.26-33.19: Warning (avoid_default_addr_size): /example-0/usb/hub@1/device@2: Relying on default #address-cells value Documentation/devicetree/bindings/usb/realtek,rts5411.example.dts:30.26-33.19: Warning (avoid_default_addr_size): /example-0/usb/hub@1/device@2: Relying on default #size-cells value Documentation/devicetree/bindings/usb/realtek,rts5411.example.dtb: Warning (unique_unit_address_if_enabled): Failed prerequisite 'avoid_default_addr_size' Documentation/devicetree/bindings/usb/realtek,rts5411.example.dts:43.23-50.19: Warning (graph_port): /example-0/usb/hub@2/ports: graph port node name should be 'port' Documentation/devicetree/bindings/usb/realtek,rts5411.example.dts:46.28-49.23: Warning (graph_endpoint): /example-0/usb/hub@2/ports/port@0: graph endpoint node name should be 'endpoint' doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20240210070934.2549994-4-swboyd@xxxxxxxxxxxx The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
