On Tue, Dec 19, 2023, Krishna Kurapati wrote: > Currently for dwc3_usb31 controller, if maximum_speed is limited to > super-speed in DT, then device mode is limited to SS, but host mode > still works in SSP. > > The documentation for max-speed property is as follows: > > "Tells USB controllers we want to work up to a certain speed. > Incase this isn't passed via DT, USB controllers should default to > their maximum HW capability." > > It doesn't specify that the property is only for device mode. > There are cases where we need to limit the host's maximum speed to > SuperSpeed only. Use this property for host mode to contrain host's > speed to SuperSpeed. > > Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx> > --- > Link to v2: https://urldefense.com/v3/__https://lore.kernel.org/all/20230514145118.20973-1-quic_kriskura@xxxxxxxxxxx/__;!!A4F2R9G_pg!d8OsArNeKYrQqDG89M-Lh-1_c7zIMZp0x1CX6X_m_D2maHEA3QM3qiQV-g4mpb12ZOPT6F8D-ESuCwHxM26peHqe5jtIkQ$ > Link to v1: https://urldefense.com/v3/__https://lore.kernel.org/all/20230512170107.18821-1-quic_kriskura@xxxxxxxxxxx/__;!!A4F2R9G_pg!d8OsArNeKYrQqDG89M-Lh-1_c7zIMZp0x1CX6X_m_D2maHEA3QM3qiQV-g4mpb12ZOPT6F8D-ESuCwHxM26peHoSWlLDaw$ > > Discussion regarding the same at: > https://urldefense.com/v3/__https://lore.kernel.org/all/e465c69c-3a9d-cbdb-d44e-96b99cfa1a92@xxxxxxxxxxx/__;!!A4F2R9G_pg!d8OsArNeKYrQqDG89M-Lh-1_c7zIMZp0x1CX6X_m_D2maHEA3QM3qiQV-g4mpb12ZOPT6F8D-ESuCwHxM26peHqdyS2ZMQ$ > --- > drivers/usb/dwc3/core.c | 12 ++++++++++++ > drivers/usb/dwc3/core.h | 5 +++++ > 2 files changed, 17 insertions(+) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index b101dbf8c5dc..056ba95d9295 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -1367,6 +1367,18 @@ static int dwc3_core_init(struct dwc3 *dwc) > > dwc3_config_threshold(dwc); > > + /* > + * Modify this for all supported Super Speed ports when > + * multiport support is added. > + */ > + if (hw_mode != DWC3_GHWPARAMS0_MODE_GADGET && > + (DWC3_IP_IS(DWC31)) && > + dwc->maximum_speed == USB_SPEED_SUPER) { > + reg = dwc3_readl(dwc->regs, DWC3_LLUCTL); > + reg |= DWC3_LLUCTL_FORCE_GEN1; > + dwc3_writel(dwc->regs, DWC3_LLUCTL, reg); > + } > + > return 0; > > err_power_off_phy: > diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h > index efe6caf4d0e8..e120611a5174 100644 > --- a/drivers/usb/dwc3/core.h > +++ b/drivers/usb/dwc3/core.h > @@ -172,6 +172,8 @@ > #define DWC3_OEVTEN 0xcc0C > #define DWC3_OSTS 0xcc10 > > +#define DWC3_LLUCTL 0xd024 > + > /* Bit fields */ > > /* Global SoC Bus Configuration INCRx Register 0 */ > @@ -657,6 +659,9 @@ > #define DWC3_OSTS_VBUSVLD BIT(1) > #define DWC3_OSTS_CONIDSTS BIT(0) > > +/* Force Gen1 speed on Gen2 link */ > +#define DWC3_LLUCTL_FORCE_GEN1 BIT(10) > + > /* Structures */ > > struct dwc3_trb; > -- > 2.42.0 > I believe you can also loop through and apply to all 16 offsets of register LLUCTL without affecting the controller. Regardless whether you will apply that for v2 or keep this version: Acked-by: Thinh Nguyen <Thinh.Nguyen@xxxxxxxxxxxx> Thanks, Thinh
