On 12/13/2023 5:22 PM, Mika Westerberg wrote:
On Wed, Dec 13, 2023 at 04:04:57PM +0530, Sanath S wrote:
On 12/13/2023 11:53 AM, Mika Westerberg wrote:
On Wed, Dec 13, 2023 at 08:18:06AM +0200, Mika Westerberg wrote:
On Wed, Dec 13, 2023 at 07:49:14AM +0200, Mika Westerberg wrote:
On Wed, Dec 13, 2023 at 12:46:35AM +0530, Sanath S wrote:
Boot firmware might have created tunnels of its own. Since we cannot
be sure they are usable for us. Tear them down and reset the ports
to handle it as a new hotplug for USB3 routers.
Suggested-by: Mario Limonciello <mario.limonciello@xxxxxxx>
Signed-off-by: Sanath S <Sanath.S@xxxxxxx>
---
drivers/thunderbolt/tb.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/drivers/thunderbolt/tb.c b/drivers/thunderbolt/tb.c
index fd49f86e0353..febd0b6972e3 100644
--- a/drivers/thunderbolt/tb.c
+++ b/drivers/thunderbolt/tb.c
@@ -2598,6 +2598,17 @@ static int tb_start(struct tb *tb)
tb_switch_tmu_enable(tb->root_switch);
/* Full scan to discover devices added before the driver was loaded. */
tb_scan_switch(tb->root_switch);
+ /*
+ * Boot firmware might have created tunnels of its own. Since we cannot
+ * be sure they are usable for us, Tear them down and reset the ports
+ * to handle it as new hotplug for USB4 routers.
+ */
+ if (tb_switch_is_usb4(tb->root_switch)) {
+ tb_switch_discover_tunnels(tb->root_switch,
+ &tcm->tunnel_list, false);
Why this is needed?
It should be enough, to do simply something like this:
if (tb_switch_is_usb4(tb->root_switch))
tb_switch_reset(tb->root_switch);
If we don't tear down of tunnels before performing the DPR, the PCIe
enumeration is failing.
PCIe link is not coming up after DPR. Below log is missing without
performing path
deactivation before performing DPR and hence PCIe enumeration is not
initiated.
[ 746.630865] pcieport 0000:00:03.1: pciehp: Slot(0-1): Card present
[ 746.630885] pcieport 0000:00:03.1: pciehp: Slot(0-1): Link Up
I think when we do a DPR, it internally does some handling with PCI Path
Enable bit(PE).
So, deactivation of PCIe path is necessary for DPR to work.
Rigth, it should be enough to reset the protocol adapter config and path
config spaces. I guess using discovery at this point is fine too but I
would at least check how complex doing the minimal "reset" turns out.
I mean in tb_switch_reset() for USB4 v1 routers it can go over all the
adapters and perform "cleanup" or so.
I gave it a thought yesterday and we can do something like this:
We are already doing tb_discovery(tb) in tb_start. This would
discover the path configuration done by Boot firmware.
Now, we can place the tb_switch_reset() right below that api with
conditions suggested by you.
And tb_switch_reset() would internally DPR for all down steam ports.
It can look something like below:
/* Find out tunnels created by the boot firmware */
tb_discover_tunnels(tb);
/*
* Reset USB4 v1 host router to get rid of possible tunnels the
* boot firmware created. This makes sure all the tunnels are
* created by us and thus have known configuration.
*
* For USB4 v2 and beyond we do this in nhi_reset() using the
* host router reset interface.
*/
if (host_reset && usb4_switch_version(tb->root_switch) == 1)
tb_switch_reset(tb->root_switch);
With this, we are making sure while we get a unplug event after doing a DPR,
We are clearing all the paths established by Boot firmware. This
wouldn't be possible
if we had not discovered the paths before we perform DPR.
It would create inconsistency for a new hot plug if we have not cleared
the path configurations
of previous hot unplug events.
Actually this needs to be done only for USB4 v1 routers since we already
reset USB4 v2 hosts so something like:
/*
* Reset USB4 v1 host router to get rid of possible tunnels the
* boot firmware created. This makes sure all the tunnels are
* created by us and thus have known configuration.
*
* For USB4 v2 and beyond we do this in nhi_reset() using the
* host router reset interface.
*/
if (usb4_switch_version(tb->root_switch) == 1)
tb_switch_reset(tb->root_switch);
(possibly add similar comment to the nhi_reset() to refer this one).
Oh, and would it be possible to tie this with the "host_reset" parameter
too somehow? I guess it could be moved to "tb.c" and "tb.h" and then
check it from nhi.c as already done and then here so this would become:
if (host_reset && usb4_switch_version(tb->root_switch) == 1)
tb_switch_reset(tb->root_switch);
Is host_reset necessary for USB4 v1 routers ? I did not use host_reset in
this case.
If its needed, then we have to modify to enable host_reset in nhi.c as well.
Well you are effectively doing that here, no? You "reset" the host
router therefore tying this to the same command line parameter makes
sense and allows user an "escape hatch" if this turns out breaking
things.
