On Tue, Dec 12, 2023 at 09:32:03AM -0600, Mario Limonciello wrote:
> On 12/12/2023 09:27, Mika Westerberg wrote:
> > On Tue, Dec 12, 2023 at 07:30:46PM +0530, Sanath S wrote:
> > > Introduce the tb_switch_reset_ports() function that resets the
> > > downstream ports of a given switch. This helps us reset the USB4
> > > links created by boot firmware during the init sequence.
> > >
> > > Introduce the tb_port_reset() helper function that resets the
> > > given port.
> > >
> > > Introduce the usb4_port_reset() function that performs the DPR
> > > of a given port. This function follows the CM guide specification 7.3
> > >
> > > Suggested-by: Mario Limonciello <mario.limonciello@xxxxxxx>
> > > Signed-off-by: Sanath S <Sanath.S@xxxxxxx>
> > > ---
> > > drivers/thunderbolt/switch.c | 31 ++++++++++++++++++++++++++++
> > > drivers/thunderbolt/tb.h | 2 ++
> > > drivers/thunderbolt/tb_regs.h | 1 +
> > > drivers/thunderbolt/usb4.c | 39 +++++++++++++++++++++++++++++++++++
> > > 4 files changed, 73 insertions(+)
> > >
> > > diff --git a/drivers/thunderbolt/switch.c b/drivers/thunderbolt/switch.c
> > > index 44e9b09de47a..26ad6cc1ee91 100644
> > > --- a/drivers/thunderbolt/switch.c
> > > +++ b/drivers/thunderbolt/switch.c
> > > @@ -626,6 +626,19 @@ int tb_port_unlock(struct tb_port *port)
> > > return 0;
> > > }
> > > +/**
> > > + * tb_port_reset() - Reset downstream port
> > > + * @port: Port to reset
> > > + *
> > > + * Helps to reconfigure the USB4 link by resetting the downstream port.
> > > + *
> > > + * Return: Returns 0 on success or an error code on failure.
> > > + */
> > > +static int tb_port_reset(struct tb_port *port)
> > > +{
> > > + return usb4_port_reset(port);
> > > +}
> > > +
> > > static int __tb_port_enable(struct tb_port *port, bool enable)
> > > {
> > > int ret;
> > > @@ -1547,6 +1560,24 @@ static void tb_dump_switch(const struct tb *tb, const struct tb_switch *sw)
> > > regs->__unknown1, regs->__unknown4);
> > > }
> > > +/**
> > > + * tb_switch_reset_ports() - Reset downstream ports of switch.
> > > + * @sw: Switch whose ports need to be reset.
> > > + *
> > > + * Return: Returns 0 on success or an error code on failure.
> > > + */
> > > +int tb_switch_reset_ports(struct tb_switch *sw)
> > > +{
> > > + struct tb_port *port;
> > > + int ret = -EINVAL;
> >
> > Why it returns -EINVAL? What if this is run for non-USB4 router?
>
> This is a good point, but in the non USB4 case (default return) maybe it's
> better to be -ENODEV and in patch 2 be careful about the caller.
Or -EOPNOTSUPP (to be consistent with the rest of the driver). Add this
to the kernel-doc too so that the caller needs to make sure
tb_switch_is_usb4() is called before this one or so.
>
> >
> > > +
> > > + tb_switch_for_each_port(sw, port) {
> > > + if (tb_port_is_null(port) && port->cap_usb4)
> > > + ret = tb_port_reset(port);
> >
> > Should it stop here and return ret?
>
> +1
>
> >
> > > + }
> > > + return ret;
> > > +}
> > > +
> > > /**
> > > * tb_switch_reset() - reconfigure route, enable and send TB_CFG_PKG_RESET
> > > * @sw: Switch to reset
> > > diff --git a/drivers/thunderbolt/tb.h b/drivers/thunderbolt/tb.h
> > > index e299e53473ae..f2687ec4ac53 100644
> > > --- a/drivers/thunderbolt/tb.h
> > > +++ b/drivers/thunderbolt/tb.h
> > > @@ -797,6 +797,7 @@ void tb_switch_remove(struct tb_switch *sw);
> > > void tb_switch_suspend(struct tb_switch *sw, bool runtime);
> > > int tb_switch_resume(struct tb_switch *sw);
> > > int tb_switch_reset(struct tb_switch *sw);
> > > +int tb_switch_reset_ports(struct tb_switch *sw);
> > > int tb_switch_wait_for_bit(struct tb_switch *sw, u32 offset, u32 bit,
> > > u32 value, int timeout_msec);
> > > void tb_sw_set_unplugged(struct tb_switch *sw);
> > > @@ -1281,6 +1282,7 @@ struct tb_port *usb4_switch_map_usb3_down(struct tb_switch *sw,
> > > int usb4_switch_add_ports(struct tb_switch *sw);
> > > void usb4_switch_remove_ports(struct tb_switch *sw);
> > > +int usb4_port_reset(struct tb_port *port);
> > > int usb4_port_unlock(struct tb_port *port);
> > > int usb4_port_hotplug_enable(struct tb_port *port);
> > > int usb4_port_configure(struct tb_port *port);
> > > diff --git a/drivers/thunderbolt/tb_regs.h b/drivers/thunderbolt/tb_regs.h
> > > index 87e4795275fe..d49530bc0d53 100644
> > > --- a/drivers/thunderbolt/tb_regs.h
> > > +++ b/drivers/thunderbolt/tb_regs.h
> > > @@ -389,6 +389,7 @@ struct tb_regs_port_header {
> > > #define PORT_CS_18_CSA BIT(22)
> > > #define PORT_CS_18_TIP BIT(24)
> > > #define PORT_CS_19 0x13
> > > +#define PORT_CS_19_DPR BIT(0)
> > > #define PORT_CS_19_PC BIT(3)
> > > #define PORT_CS_19_PID BIT(4)
> > > #define PORT_CS_19_WOC BIT(16)
> > > diff --git a/drivers/thunderbolt/usb4.c b/drivers/thunderbolt/usb4.c
> > > index 4277733d0021..55f7c163bf84 100644
> > > --- a/drivers/thunderbolt/usb4.c
> > > +++ b/drivers/thunderbolt/usb4.c
> > > @@ -1073,6 +1073,45 @@ void usb4_switch_remove_ports(struct tb_switch *sw)
> > > }
> > > }
> > > +/**
> > > + * usb4_port_reset() - Reset USB4 downsteam port
> > > + * @port: USB4 port to reset.
> > > + *
> > > + * Helps to reconfigure USB4 link by resetting downstream port.
> > > + *
> > > + * Return: Returns 0 on success or an error code on failure.
> > > + */
> > > +int usb4_port_reset(struct tb_port *port)
> > > +{
> > > + int ret;
> > > + u32 val = 0;
> >
> > Reverse christmas tree please:
> >
> > u32 val = 0;
> > int ret;
> >
> > > +
> > > + ret = tb_port_read(port, &val, TB_CFG_PORT,
> > > + port->cap_usb4 + PORT_CS_19, 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + val = val | PORT_CS_19_DPR;
> > > + ret = tb_port_write(port, &val, TB_CFG_PORT,
> > > + port->cap_usb4 + PORT_CS_19, 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + /* Wait for 10ms after requesting downstream port reset */
> > > + msleep(10);
> >
> > Probably good to add a couple of more ms just in case. Also
> > usleep_range()? (or fsleep()).
>
> Sanath had it at 20 but I had suggested to align to spec.
> For the wiggle room maybe usleep_range(10000, 15000)?
Works for me.
>
> >
> > > +
> > > + ret = tb_port_read(port, &val, TB_CFG_PORT,
> > > + port->cap_usb4 + PORT_CS_19, 1);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + val &= ~PORT_CS_19_DPR;
> > > + ret = tb_port_write(port, &val, TB_CFG_PORT,
> > > + port->cap_usb4 + PORT_CS_19, 1);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > /**
> > > * usb4_port_unlock() - Unlock USB4 downstream port
> > > * @port: USB4 port to unlock
> > > --
> > > 2.34.1
