I have a digital photo frame agfa af 5080ms
Windows recognizes it as 4 mass storage devices
on linux it appears in dmesg but doesn't work
lsusb -v
Bus 001 Device 015: ID 067b:1063 Prolific Technology, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x067b Prolific Technology, Inc.
idProduct 0x1063
bcdDevice 1.00
iManufacturer 1 Linux 2.4.20-uc0-61d with pl1063
iProduct 2 Prolific Storage Gadget
iSerial 3 3135204E6F76
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
and the dmesg output by connecting it
usb 1-3: new high speed USB device using ehci_hcd and address 11
usb 1-3: configuration #1 chosen from 1 choice
scsi11 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 11
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 11:0:0:0: Direct-Access PL1063 USB 0100 PQ: 0 ANSI: 4
scsi 11:0:0:1: Direct-Access PL1063 ALLIN1 0100 PQ: 0 ANSI: 4
scsi 11:0:0:2: Direct-Access PL1063 IDE 0100 PQ: 0 ANSI: 4
scsi 11:0:0:3: Direct-Access PL1063 OBNAND 0100 PQ: 0 ANSI: 4
sd 11:0:0:0: Attached scsi generic sg1 type 0
sd 11:0:0:1: Attached scsi generic sg2 type 0
sd 11:0:0:2: Attached scsi generic sg3 type 0
sd 11:0:0:3: Attached scsi generic sg4 type 0
usb 1-3: reset high speed USB device using ehci_hcd and address 11
and disconnecting
usb 1-3: USB disconnect, address 11
sd 11:0:0:1: Device offlined - not ready after error recovery
sd 11:0:0:0: [sdb] Attached SCSI removable disk
sd 11:0:0:3: [sde] READ CAPACITY failed
sd 11:0:0:3: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 11:0:0:3: [sde] Sense not available.
sd 11:0:0:3: [sde] Write Protect is off
sd 11:0:0:3: [sde] Mode Sense: 00 00 00 00
sd 11:0:0:3: [sde] Assuming drive cache: write through
sd 11:0:0:3: [sde] READ CAPACITY failed
sd 11:0:0:3: [sde] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 11:0:0:3: [sde] Sense not available.
sd 11:0:0:3: [sde] Assuming drive cache: write through
sd 11:0:0:3: [sde] Attached SCSI removable disk
sd 11:0:0:1: [sdc] Attached SCSI removable disk
sd 11:0:0:2: [sdd] READ CAPACITY failed
sd 11:0:0:2: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 11:0:0:2: [sdd] Sense not available.
sd 11:0:0:2: [sdd] Write Protect is off
sd 11:0:0:2: [sdd] Mode Sense: 38 3a 31 36
sd 11:0:0:2: [sdd] Assuming drive cache: write through
sd 11:0:0:2: [sdd] READ CAPACITY failed
sd 11:0:0:2: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 11:0:0:2: [sdd] Sense not available.
sd 11:0:0:2: [sdd] Assuming drive cache: write through
sd 11:0:0:2: [sdd] Attached SCSI removable disk
but doesn't appears in /dev
ls /dev/sd*
/dev/sda /dev/sda1 /dev/sda2 /dev/sda3 /dev/sda4
is there a any easy way to get it to work ?
--
Pozdrawiam
Daniel Kukuła
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
