[PATCH RFC v4 3/6] ARM: pxa: Convert Spitz CF power control to GPIO descriptors

[Duje Mihanović <duje.mihanovic@xxxxxxxx>]

Sharp's Spitz board still uses the legacy GPIO interface for controlling
the power supply to its CF and SD card slots.

Convert it to use the GPIO descriptor interface.

Acked-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
Signed-off-by: Duje Mihanović <duje.mihanovic@xxxxxxxx>
---
 arch/arm/mach-pxa/spitz.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index b6a4085e9fb0..965354e64c68 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -133,6 +133,10 @@ static unsigned long spitz_pin_config[] __initdata = {
  * Scoop GPIO expander
  ******************************************************************************/
 #if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE)
+GPIO_LOOKUP_SINGLE(spitz_card_pwr_ctrl_gpio_table, "pxa2xx-mci.0",
+		"sharp-scoop", SPITZ_GPIO_CF_POWER, "cf_power",
+		GPIO_ACTIVE_HIGH);
+
 /* SCOOP Device #1 */
 static struct resource spitz_scoop_1_resources[] = {
 	[0] = {
@@ -190,6 +194,7 @@ struct platform_device spitz_scoop_2_device = {
 static void __init spitz_scoop_init(void)
 {
 	platform_device_register(&spitz_scoop_1_device);
+	gpiod_add_lookup_table(&spitz_card_pwr_ctrl_gpio_table);
 
 	/* Akita doesn't have the second SCOOP chip */
 	if (!machine_is_akita())
@@ -201,9 +206,18 @@ static void __maybe_unused spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
 {
 	unsigned short cpr;
 	unsigned long flags;
+	struct gpio_desc *cf_power;
+
+	cf_power = gpiod_get(&pxa_device_mci.dev, "cf_power", GPIOD_ASIS);
+	if (IS_ERR(cf_power)) {
+		dev_err(&pxa_device_mci.dev,
+				"failed to get power control GPIO with %ld\n",
+				PTR_ERR(cf_power));
+		return;
+	}
 
 	if (new_cpr & 0x7) {
-		gpio_set_value(SPITZ_GPIO_CF_POWER, 1);
+		gpiod_direction_output(cf_power, 1);
 		mdelay(5);
 	}
 
@@ -222,8 +236,10 @@ static void __maybe_unused spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
 
 	if (!(cpr & 0x7)) {
 		mdelay(1);
-		gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
+		gpiod_direction_output(cf_power, 0);
 	}
+
+	gpiod_put(cf_power);
 }
 
 #else

-- 
2.42.0