Re: [PATCH v9 07/10] usb: dwc3: qcom: Add multiport suspend/resume support for wrapper

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jun 21, 2023 at 10:06:25AM +0530, Krishna Kurapati wrote:
> QCOM SoC SA8295P's tertiary quad port controller supports 2 HS+SS
> ports and 2 HS only ports. Add support for configuring PWR_EVENT_IRQ's
> for all the ports during suspend/resume.

Please be more specific here. You don't seem to be configuring anything.

> Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
> ---
>  drivers/usb/dwc3/dwc3-qcom.c | 48 +++++++++++++++++++++++++++++++-----
>  1 file changed, 42 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
> index 3ab48a6925fe..699485a85233 100644
> --- a/drivers/usb/dwc3/dwc3-qcom.c
> +++ b/drivers/usb/dwc3/dwc3-qcom.c
> @@ -37,7 +37,11 @@
>  #define PIPE3_PHYSTATUS_SW			BIT(3)
>  #define PIPE_UTMI_CLK_DIS			BIT(8)
>  
> -#define PWR_EVNT_IRQ_STAT_REG			0x58
> +#define PWR_EVNT_IRQ1_STAT_REG			0x58
> +#define PWR_EVNT_IRQ2_STAT_REG			0x1dc
> +#define PWR_EVNT_IRQ3_STAT_REG			0x228
> +#define PWR_EVNT_IRQ4_STAT_REG			0x238
> +
>  #define PWR_EVNT_LPM_IN_L2_MASK			BIT(4)
>  #define PWR_EVNT_LPM_OUT_L2_MASK		BIT(5)
>  
> @@ -93,6 +97,13 @@ struct dwc3_qcom {
>  	struct icc_path		*icc_path_apps;
>  };
>  
> +static u32 pwr_evnt_irq_stat_reg_offset[4] = {
> +	PWR_EVNT_IRQ1_STAT_REG,
> +	PWR_EVNT_IRQ2_STAT_REG,
> +	PWR_EVNT_IRQ3_STAT_REG,
> +	PWR_EVNT_IRQ4_STAT_REG,
> +};
> +
>  static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val)
>  {
>  	u32 reg;
> @@ -417,17 +428,37 @@ static void dwc3_qcom_enable_interrupts(struct dwc3_qcom *qcom)
>  	dwc3_qcom_enable_wakeup_irq(qcom->ss_phy_irq[0], 0);
>  }
>  
> +static u8 dwc3_qcom_get_port_info(struct dwc3_qcom *qcom)

"port_info" is not very specific, call it get_num_ports() or similar.

> +{
> +	struct dwc3 __maybe_unused *dwc = platform_get_drvdata(qcom->dwc3);

__maybe unused makes no sense here.

> +
> +	if (dwc3_qcom_is_host(qcom))
> +		return dwc->num_usb2_ports;

Here you're accessing the core driver data again, which we want to
avoid going forward so this at least warrants a FIXME to rework this as
well.

> +
> +	/*
> +	 * If not in host mode, either dwc was not probed
> +	 * or we are in device mode, either case checking for
> +	 * only first pwr event irq would suffice.

Rewrap comment at 80 columns.

> +	 */
> +
> +	return 1;
> +}
> +
>  static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup)
>  {
>  	u32 val;
>  	int i, ret;
> +	u8 num_ports;

Move first.

>  	if (qcom->is_suspended)
>  		return 0;
>  
> -	val = readl(qcom->qscratch_base + PWR_EVNT_IRQ_STAT_REG);
> -	if (!(val & PWR_EVNT_LPM_IN_L2_MASK))
> +	num_ports = dwc3_qcom_get_port_info(qcom);
> +	for (i = 0; i < num_ports; i++) {
> +		val = readl(qcom->qscratch_base + pwr_evnt_irq_stat_reg_offset[i]);
> +		if (!(val & PWR_EVNT_LPM_IN_L2_MASK))
>  		dev_err(qcom->dev, "HS-PHY not in L2\n");

This line is not indented properly.

Make sure to run checkpatch before submitting so that I don't have to
point out things like this again.

> +	}
>  
>  	for (i = qcom->num_clocks - 1; i >= 0; i--)
>  		clk_disable_unprepare(qcom->clks[i]);
> @@ -452,12 +483,14 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup)
>  
>  static int dwc3_qcom_resume(struct dwc3_qcom *qcom, bool wakeup)
>  {
> +	int num_ports;
>  	int ret;
>  	int i;
>  
>  	if (!qcom->is_suspended)
>  		return 0;
>  
> +	num_ports = dwc3_qcom_get_port_info(qcom);

Move below to where you use num_ports.

>  	if (dwc3_qcom_is_host(qcom) && wakeup)
>  		dwc3_qcom_disable_interrupts(qcom);
>  
> @@ -474,9 +507,12 @@ static int dwc3_qcom_resume(struct dwc3_qcom *qcom, bool wakeup)
>  	if (ret)
>  		dev_warn(qcom->dev, "failed to enable interconnect: %d\n", ret);
>  
> -	/* Clear existing events from PHY related to L2 in/out */

No need to move the comment.

> -	dwc3_qcom_setbits(qcom->qscratch_base, PWR_EVNT_IRQ_STAT_REG,
> -			  PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK);
> +	for (i = 0; i < num_ports; i++) {
> +		/* Clear existing events from PHY related to L2 in/out */
> +		dwc3_qcom_setbits(qcom->qscratch_base,
> +			pwr_evnt_irq_stat_reg_offset[i],
> +			PWR_EVNT_LPM_IN_L2_MASK | PWR_EVNT_LPM_OUT_L2_MASK);

Indent continuation lines at least two tabs further than the previous
line.

> +	}
>  
>  	qcom->is_suspended = false;

Johan



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux