On Sun, May 14, 2023 at 11:19:14AM +0530, Krishna Kurapati wrote: > QCOM SoC SA8295P's tertiary quad port controller supports 2 HS+SS > ports and 2 HS only ports. Add support for configuring PWR_EVENT_IRQ's > for all the ports during suspend/resume. > > Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx> > --- > drivers/usb/dwc3/dwc3-qcom.c | 28 ++++++++++++++++++++++------ > 1 file changed, 22 insertions(+), 6 deletions(-) > > diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c > index 959fc925ca7c..7a9bce66295d 100644 > --- a/drivers/usb/dwc3/dwc3-qcom.c > +++ b/drivers/usb/dwc3/dwc3-qcom.c > @@ -37,7 +37,10 @@ > #define PIPE3_PHYSTATUS_SW BIT(3) > #define PIPE_UTMI_CLK_DIS BIT(8) > > -#define PWR_EVNT_IRQ_STAT_REG 0x58 > +#define PWR_EVNT_IRQ1_STAT_REG 0x58 > +#define PWR_EVNT_IRQ2_STAT_REG 0x1dc > +#define PWR_EVNT_IRQ3_STAT_REG 0x228 > +#define PWR_EVNT_IRQ4_STAT_REG 0x238 > #define PWR_EVNT_LPM_IN_L2_MASK BIT(4) > #define PWR_EVNT_LPM_OUT_L2_MASK BIT(5) > > @@ -93,6 +96,13 @@ struct dwc3_qcom { > struct icc_path *icc_path_apps; > }; > > +static u32 pwr_evnt_irq_stat_reg_offset[4] = { > + PWR_EVNT_IRQ1_STAT_REG, > + PWR_EVNT_IRQ2_STAT_REG, > + PWR_EVNT_IRQ3_STAT_REG, > + PWR_EVNT_IRQ4_STAT_REG, Seems to be excessive indentation of these... Can you also please confirm that these should be counted starting at 1 - given that you otherwise talk about port0..N-1? > +}; > + > static inline void dwc3_qcom_setbits(void __iomem *base, u32 offset, u32 val) > { > u32 reg; > @@ -413,13 +423,16 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup) > { > u32 val; > int i, ret; > + struct dwc3 *dwc = platform_get_drvdata(qcom->dwc3); > > if (qcom->is_suspended) > return 0; > > - val = readl(qcom->qscratch_base + PWR_EVNT_IRQ_STAT_REG); > - if (!(val & PWR_EVNT_LPM_IN_L2_MASK)) > - dev_err(qcom->dev, "HS-PHY not in L2\n"); > + for (i = 0; i < dwc->num_usb2_ports; i++) { In the event that the dwc3 core fails to acquire or enable e.g. clocks its drvdata will be NULL. If you then hit a runtime pm transition in the dwc3-qcom glue you will dereference NULL here. (You can force this issue by e.g. returning -EINVAL from dwc3_clk_enable()). So if you're peaking into qcom->dwc3 you need to handle the fact that dwc might be NULL, here and in resume below. Regards, Bjorn