Re: [PATCH v3] dt-bindings: usb: Add support for Microchip usb5744 hub controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 10/05/2023 16:34, Michal Simek wrote:
> The Microchip usb5744 is a SS/HS USB 3.0 hub controller with 4 ports.
> Add description for USB related aspects of the USB5744 hub, it as
> well cover the option of connecting the controller as an i2c slave.
> When i2c interface is connected hub needs to be initialized first.
> Hub itself has fixed i2c address 0x2D but hardcoding address is not good
> idea because address can be shifted by i2c address translator in the
> middle.
> 
> Signed-off-by: Piyush Mehta <piyush.mehta@xxxxxxx>
> Signed-off-by: Michal Simek <michal.simek@xxxxxxx>
> ---
> 
> Changes in v3:
> - add maxItems to reg property
> - remove select and define properties not used for i2c node and required
>   for usb
> - s/binding/support/ in subject
> - reword descripion to remove binding word from commit message
> - wire usb-device.yaml for usb hub properties
> 
> Changes in v2:
> - fix i2c-bus property
> - swap usb2.0/3.0 compatible strings
> - fix indentation in example (4 spaces)
> - add new i2c node with microchip,usb5744 compatible property
> 
> It looks like that usb8041 has also an optional i2c interface which is not
> covered. But it is mentioned at commit 40e58a8a7ca6 ("dt-bindings: usb:
> Add binding for TI USB8041 hub controller").
> 
> i2c-bus name property was suggested by Rob at
> https://lore.kernel.org/all/CAL_JsqJedhX6typpUKbnzV7CLK6UZVjq3CyG9iY_j5DLPqvVdw@xxxxxxxxxxxxxx/
> and
> https://lore.kernel.org/all/CAL_JsqJZBbu+UXqUNdZwg-uv0PAsNg55026PTwhKr5wQtxCjVQ@xxxxxxxxxxxxxx/
> 
> the question is if adding address like this is acceptable.
> But it must be specified.
> 
> Driver will follow based on final dt-binding.
> 
> $ref: usb-device.yaml# should be also added but have no idea how to wire it
> up to be applied only on usb node not i2c one.
> 
> ---
>  .../bindings/usb/microchip,usb5744.yaml       | 107 ++++++++++++++++++
>  1 file changed, 107 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
> 
> diff --git a/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml b/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
> new file mode 100644
> index 000000000000..408c5bf00cc2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
> @@ -0,0 +1,107 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/microchip,usb5744.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Microchip USB5744 4-port Hub Controller
> +
> +description:
> +  Microchip's USB5744 SmartHubTM IC is a 4 port, SuperSpeed (SS)/Hi-Speed (HS),
> +  low power, low pin count configurable and fully compliant with the USB 3.1
> +  Gen 1 specification. The USB5744 also supports Full Speed (FS) and Low Speed
> +  (LS) USB signaling, offering complete coverage of all defined USB operating
> +  speeds. The new SuperSpeed hubs operate in parallel with the USB 2.0
> +  controller, so 5 Gbps SuperSpeed data transfers are not affected by slower
> +  USB 2.0 traffic.
> +
> +maintainers:
> +  - Piyush Mehta <piyush.mehta@xxxxxxx>
> +  - Michal Simek <michal.simek@xxxxxxx>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - usb424,2744
> +      - usb424,5744
> +      - microchip,usb5744
> +
> +  reg:
> +    maxItems: 1
> +
> +  reset-gpios:
> +    maxItems: 1
> +    description:
> +      GPIO controlling the GRST# pin.
> +
> +  vdd-supply:
> +    description:
> +      VDD power supply to the hub
> +
> +  peer-hub:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      phandle to the peer hub on the controller.
> +
> +  i2c-bus:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      phandle of an usb hub connected via i2c bus.
> +
> +allOf:

Put allOf: block after required:. Just like in example schema.

> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            const: microchip,usb5744
> +    then:
> +      properties:
> +        reset-gpios: false
> +        vdd-supply: false
> +        peer-hub: false
> +        i2c-bus: false
> +    else:
> +      $ref: /schemas/usb/usb-device.yaml
> +      required:
> +        - peer-hub
> +
> +required:
> +  - compatible
> +  - reg
> +


Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>

Best regards,
Krzysztof




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux