Re: [RFC PATCH v2 12/22] sound: usb: card: Introduce USB SND platform op callbacks

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Greg,

On 2/27/2023 11:30 PM, Greg KH wrote:
On Mon, Feb 27, 2023 at 06:59:32PM -0800, Wesley Cheng wrote:
Hi Greg,

On 2/10/2023 2:49 PM, Wesley Cheng wrote:
Hi Greg,

On 1/28/2023 5:28 AM, Greg KH wrote:
On Wed, Jan 25, 2023 at 07:14:14PM -0800, Wesley Cheng wrote:
Allow for different platforms to be notified on USB SND
connect/disconnect
seqeunces.  This allows for platform USB SND modules to properly
initialize
and populate internal structures with references to the USB SND chip
device.

Signed-off-by: Wesley Cheng <quic_wcheng@xxxxxxxxxxx>
---
   sound/usb/card.c | 28 ++++++++++++++++++++++++++++
   sound/usb/card.h | 20 ++++++++++++++++++++
   2 files changed, 48 insertions(+)

diff --git a/sound/usb/card.c b/sound/usb/card.c
index 26268ffb8274..803230343c16 100644
--- a/sound/usb/card.c
+++ b/sound/usb/card.c
@@ -117,6 +117,24 @@ MODULE_PARM_DESC(skip_validation, "Skip
unit descriptor validation (default: no)
   static DEFINE_MUTEX(register_mutex);
   static struct snd_usb_audio *usb_chip[SNDRV_CARDS];
   static struct usb_driver usb_audio_driver;
+static struct snd_usb_platform_ops *platform_ops;

You can not have a single "platform_ops" pointer, this HAS to be
per-bus.


Agreed.


I looked at seeing how we could implement this at a per bus level, but the
USB class driver model doesn't exactly have a good framework for supporting
this.  Reason being is because, at the time of the USB SND class driver
initialization, there is a big chance that there isn't a USB bus registered
in the system, so the point of adding the operations is not clear.  However,
we need to ensure that we've added the platform/driver operations before any
USB SND devices are detected.

But the offload "engine" is associated with the specific USB bus
controller instance in the system, so perhaps you are just not adding
this to the correct location?


There are several parts to the offload logic:
1. XHCI interrupter/resource components - fetching addresses to the proper event ring and transfer rings for the audio DSP. This is the part which is specific to the controller instance, and APIs are being directly exported from the XHCI HCD, as the offloading features utilized are only specific for XHCI based controllers. This is handled in patches 1-6 in this series. Each XHCI instance will have its own set of interrupters, and transfer resources.

2. USB offload class driver - driver which interacts with USB SND for operations like UAC descriptor parsing, USB audio device support params, and USB endpoint setup (ie issuing SET_INTERFACE to enable the device to start playback this is a SETUP transaction). It will interact with the USB backend and items in #1, to set up the audio playback.

The sound core shouldn't care about this at all, add the logic to the
USB host controller driver instead, why isn't this just another USB bus
function?


The intention of the platform ops here is to mainly keep track of USB SND card/pcm device creation, and access to the main "struct snd_usb_audio". This structure carries all the information about the different substreams allocated, as well as the formats supported by the audio device. This is passed onto the USB backend, which will be utilized in my next revision to allow userspace to specifically select the proper card/PCM device to enable offload on.

To add to the above, in case of OTG/DRD (dual role) designs, the USB HCD/bus
isn't created until we move into the host role.  At that time, using DWC3 as
an example, we will create the XHCI platform device, and probe the USB HCD,
where a USB bus is created.

Great, again, tie it to the specific xhci host controler instance.

In general, we currently think this USB offload driver should co-exist with
the USB SND class driver, which handles all devices connected across every
bus.

And that is incorrect, please do not do that.


To clarify, I think we can summarize that the qc_audio_offload driver (the one that registers the platform operations) is mainly responsible for USB SND card management, and communicating that to the USB backend.

We can add a check to the platform connect routine to ensure that
there is a reference to the USB backend.  If so, then that particular USB
bus/sysdev can be supported by the audio DSP.  That way, we do not falsely
populate USB SND cards which are present on another USB bus/controller.

You should NEVER be able to populate a USB card unless the USB bus
controller has given you the USB interface structure to control, so I do
not understand how this is an issue.


This might not be so clear with the current revision. In the next revision I have prepared, as I mentioned, we are proposing using the platform connect/disconnect ops here to build a reference to all USB SND card and PCM devices available in the system.

For example, if you have an external hub connected to the root hub, and each port on that hub has an audio device connected. We want to allow userspace to select which card# and pcm# to start offload on. (versus userspace having to rely on trail and error, which Pierre touched on on why that is not desired)

Since the USB SND driver is based on udevs (not bus specific), if there are multiple roothubs (correlates to usb buses), then we only want to notify the USB backend of the USB SND cards on the controller which has offloading enabled. Otherwise, if userspace selects a device on an unsupported controller, then that path would obviously fail.

I hope that clarifies some things.

Thanks
Wesley Cheng



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux