On Mon, Oct 10, 2022 at 06:18:11PM +0800, Peng Fan (OSS) wrote: > From: Peng Fan <peng.fan@xxxxxxx> > > Convert the binding to yaml format s/yaml/DT schema/ > > Signed-off-by: Peng Fan <peng.fan@xxxxxxx> > --- > .../devicetree/bindings/usb/ci-hdrc-usb2.txt | 158 --------- > .../devicetree/bindings/usb/ci-hdrc-usb2.yaml | 306 ++++++++++++++++++ > 2 files changed, 306 insertions(+), 158 deletions(-) > delete mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > create mode 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml > diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml > new file mode 100644 > index 000000000000..1c10691c45f2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml > @@ -0,0 +1,306 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/usb/ci-hdrc-usb2.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: USB2 ChipIdea USB controller for ci13xxx Binding > + > +maintainers: > + - Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> > + > +properties: > + compatible: > + oneOf: > + - enum: > + - chipidea,usb2 > + - lsi,zevio-usb > + - nvidia,tegra20-udc > + - nvidia,tegra30-udc > + - nvidia,tegra114-udc > + - nvidia,tegra124-udc > + - qcom,ci-hdrc > + - items: > + - enum: > + - fsl,imx23-usb > + - fsl,imx25-usb > + - fsl,imx28-usb > + - fsl,imx6q-usb > + - fsl,imx6sl-usb > + - fsl,imx6sx-usb > + - fsl,imx6ul-usb > + - fsl,imx7d-usb > + - const: fsl,imx27-usb > + - items: > + - const: fsl,imx7ulp-usb > + - const: fsl,imx6ul-usb > + - items: > + - const: lsi,zevio-usb > + - items: > + - const: xlnx,zynq-usb-2.20a > + - const: chipidea,usb2 > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + maxItems: 2 > + > + itc-setting: > + description: > + interrupt threshold control register control, the setting should be > + aligned with ITC bits at register USBCMD. > + $ref: /schemas/types.yaml#/definitions/uint32 > + > + ahb-burst-config: > + description: > + it is vendor dependent, the required value should be aligned with > + AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is > + used to change AHB burst configuration, check the chipidea spec for > + meaning of each value. If this property is not existed, it will use > + the reset value. > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0x0 > + maximum: 0x7 > + > + tx-burst-size-dword: > + description: > + it is vendor dependent, the tx burst size in dword (4 bytes), This > + register represents the maximum length of a the burst in 32-bit > + words while moving data from system memory to the USB bus, the value > + of this property will only take effect if property "ahb-burst-config" > + is set to 0, if this property is missing the reset default of the > + hardware implementation will be used. > + $ref: /schemas/types.yaml#/definitions/uint32 > + > + rx-burst-size-dword: > + description: > + it is vendor dependent, the rx burst size in dword (4 bytes), This > + register represents the maximum length of a the burst in 32-bit words > + while moving data from the USB bus to system memory, the value of > + this property will only take effect if property "ahb-burst-config" > + is set to 0, if this property is missing the reset default of the > + hardware implementation will be used. > + $ref: /schemas/types.yaml#/definitions/uint32 > + > + extcon: > + description: | > + Phandles to external connector devices. First phandle should point > + to external connector, which provide "USB" cable events, the second > + should point to external connector device, which provide "USB-HOST" > + cable events. If one of the external connector devices is not > + required, empty <0> phandle should be specified. > + > + phy-clkgate-delay-us: > + description: | > + The delay time (us) between putting the PHY into low power mode and > + gating the PHY clock. > + > + non-zero-ttctrl-ttha: > + description: | > + After setting this property, the value of register ttctrl.ttha > + will be 0x7f; if not, the value will be 0x0, this is the default > + value. It needs to be very carefully for setting this property, it > + is recommended that consult with your IC engineer before setting > + this value. On the most of chipidea platforms, the "usage_tt" flag > + at RTL is 0, so this property only affects siTD. > + > + If this property is not set, the max packet size is 1023 bytes, and > + if the total of packet size for pervious transactions are more than > + 256 bytes, it can't accept any transactions within this frame. The > + use case is single transaction, but higher frame rate. > + > + If this property is set, the max packet size is 188 bytes, it can > + handle more transactions than above case, it can accept transactions > + until it considers the left room size within frame is less than 188 > + bytes, software needs to make sure it does not send more than 90% > + maximum_periodic_data_per_frame. The use case is multiple > + transactions, but less frame rate. > + > + mux-controls: > + description: | > + The mux control for toggling host/device output of this controller. > + It's expected that a mux state of 0 indicates device mode and a mux > + state of 1 indicates host mode. > + > + mux-control-names: > + description: Shall be "usb_switch" if mux-controls is specified. > + > + pinctrl-names: > + description: | > + Names for optional pin modes in "default", "host", "device". > + In case of HSIC-mode, "idle" and "active" pin modes are mandatory. > + In this case, the "idle" state needs to pull down the data and > + strobe pin and the "active" state needs to pull up the strobe pin. > + > + pinctrl-0: > + maxItems: 1 > + > + pinctrl-1: > + maxItems: 1 > + > + phys: > + maxItems: 1 > + > + phy-names: > + const: usb-phy > + > + vbus-supply: > + description: reference to the VBUS regulator. > + > +required: > + - compatible > + - reg > + - interrupts > + > +allOf: > + - $ref: usb-drd.yaml# > + - $ref: usb-hcd.yaml# > + - if: > + properties: > + mux-controls: > + true > + then: > + properties: > + mux-control-names: > + const: usb_switch > + - if: > + properties: > + phy_type: > + const: hsic > + > + required: > + - phy_type > + then: > + properties: > + pinctrl-names: > + items: > + - const: idle > + - const: active > + else: > + properties: > + pinctrl-names: > + oneOf: > + - items: > + - const: default > + - enum: > + - host > + - device > + - items: > + - const: default > + - if: > + properties: > + compatible: > + enum: > + - fsl,imx23-usb > + - fsl,imx25-usb > + - fsl,imx27-usb > + - fsl,imx28-usb > + - fsl,imx6q-usb > + - fsl,imx6sl-usb > + - fsl,imx6sx-usb > + - fsl,imx6ul-usb > + - fsl,imx7d-usb > + - fsl,imx7ulp-usb > + then: > + properties: > + fsl,usbmisc: > + description: > + Phandler of non-core register device, with one argument that > + indicate usb controller index type ref? Don't define properties within if/then/else. Define at top level and then restrict presence in the if/then schema. > + > + disable-over-current: > + description: disable over current detect > + > + over-current-active-low: > + description: over current signal polarity is active low > + > + over-current-active-high: > + description: | > + Over current signal polarity is active high. It's recommended to > + specify the over current polarity. > + > + power-active-high: > + description: power signal polarity is active high > + > + external-vbus-divider: > + description: enables off-chip resistor divider for Vbus > + > + samsung,picophy-pre-emp-curr-control: > + description: | > + HS Transmitter Pre-Emphasis Current Control. This signal controls > + the amount of current sourced to the USB_OTG*_DP and USB_OTG*_DN > + pins after a J-to-K or K-to-J transition. The range is from 0x0 to > + 0x3, the default value is 0x1. Details can refer to TXPREEMPAMPTUNE0 > + bits of USBNC_n_PHY_CFG1. > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0x0 > + maximum: 0x3 > + > + samsung,picophy-dc-vol-level-adjust: > + description: | > + HS DC Voltage Level Adjustment. Adjust the high-speed transmitter DC > + level voltage. The range is from 0x0 to 0xf, the default value is > + 0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1. > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0x0 > + maximum: 0xf > + > +additionalProperties: true Cannot be true. > + > +examples: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/clock/berlin2.h> > + > + usb@f7ed0000 { > + compatible = "chipidea,usb2"; Doesn't match documentation. You should know by now to test your bindings. > + reg = <0xf7ed0000 0x10000>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&chip CLKID_USB0>; > + phys = <&usb_phy0>; > + phy-names = "usb-phy"; > + vbus-supply = <®_usb0_vbus>; > + itc-setting = <0x4>; /* 4 micro-frames */ > + /* Incremental burst of unspecified length */ > + ahb-burst-config = <0x0>; > + tx-burst-size-dword = <0x10>; /* 64 bytes */ > + rx-burst-size-dword = <0x10>; > + extcon = <0>, <&usb_id>; > + phy-clkgate-delay-us = <400>; > + mux-controls = <&usb_switch>; > + mux-control-names = "usb_switch"; > + }; > + > + # Example for HSIC: > + - | > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + #include <dt-bindings/clock/imx6qdl-clock.h> > + > + usb@2184400 { > + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; > + reg = <0x02184400 0x200>; > + interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6QDL_CLK_USBOH3>; > + fsl,usbphy = <&usbphynop1>; > + fsl,usbmisc = <&usbmisc 2>; > + phy_type = "hsic"; > + dr_mode = "host"; > + ahb-burst-config = <0x0>; > + tx-burst-size-dword = <0x10>; > + rx-burst-size-dword = <0x10>; > + pinctrl-names = "idle", "active"; > + pinctrl-0 = <&pinctrl_usbh2_idle>; > + pinctrl-1 = <&pinctrl_usbh2_active>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + usbnet: ethernet@1 { > + compatible = "usb424,9730"; > + reg = <1>; > + }; > + }; > + > +... > -- > 2.37.1 > >
