Il 28/09/22 11:17, Chunfeng Yun ha scritto:
It happens when enable uvc function, the flow as below:
the controller switch to data stage, then call
-> foward_to_driver() -> composite_setup() -> uvc_function_setup(),
it send out an event to user layer to notify it call
-> ioctl() -> uvc_send_response() -> usb_ep_queue(),
but before the user call ioctl to queue ep0's buffer, the host already send
out data, but the controller find that no buffer is queued to receive data,
it send out STALL handshake.
To fix the issue, don't send out ACK of setup stage to switch to out data
stage until the buffer is available.
Cc: <Stable@xxxxxxxxxxxxxxx>
Reported-by: Min Guo <min.guo@xxxxxxxxxxxx>
Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
---
drivers/usb/mtu3/mtu3.h | 4 ++++
drivers/usb/mtu3/mtu3_gadget_ep0.c | 22 +++++++++++++++++++---
2 files changed, 23 insertions(+), 3 deletions(-)
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
index 2d7b57e07eee..6b64ad17724d 100644
--- a/drivers/usb/mtu3/mtu3.h
+++ b/drivers/usb/mtu3/mtu3.h
@@ -318,6 +318,9 @@ static inline struct ssusb_mtk *dev_to_ssusb(struct device *dev)
* for GET_STATUS and SET_SEL
* @setup_buf: ep0 response buffer for GET_STATUS and SET_SEL requests
* @u3_capable: is capable of supporting USB3
+ * @delayed_setup: delay the setup stage to avoid STALL handshake in
+ * out data stage due to the class driver doesn't queue buffer
+ * before the host send out data
*/
struct mtu3 {
spinlock_t lock;
@@ -360,6 +363,7 @@ struct mtu3 {
unsigned connected:1;
unsigned async_callbacks:1;
unsigned separate_fifo:1;
+ unsigned delayed_setup:1;
u8 address;
u8 test_mode_nr;
diff --git a/drivers/usb/mtu3/mtu3_gadget_ep0.c b/drivers/usb/mtu3/mtu3_gadget_ep0.c
index e4fd1bb14a55..f7a71cc83e15 100644
--- a/drivers/usb/mtu3/mtu3_gadget_ep0.c
+++ b/drivers/usb/mtu3/mtu3_gadget_ep0.c
@@ -162,6 +162,19 @@ static void ep0_do_status_stage(struct mtu3 *mtu)
mtu3_writel(mbase, U3D_EP0CSR, value | EP0_SETUPPKTRDY | EP0_DATAEND);
}
+/* delay sending out ACK of setup stage to wait for OUT buffer queued */
+static void ep0_setup_stage_send_ack(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 value;
+
+ if (mtu->delayed_setup) {
+ value = mtu3_readl(mbase, U3D_EP0CSR) & EP0_W1C_BITS;
+ mtu3_writel(mbase, U3D_EP0CSR, value | EP0_SETUPPKTRDY);
+ mtu->delayed_setup = 0;
+ }
+}
+
static int ep0_queue(struct mtu3_ep *mep0, struct mtu3_request *mreq);
static void ep0_dummy_complete(struct usb_ep *ep, struct usb_request *req)
@@ -628,8 +641,9 @@ static void ep0_read_setup(struct mtu3 *mtu, struct usb_ctrlrequest *setup)
csr | EP0_SETUPPKTRDY | EP0_DPHTX);
mtu->ep0_state = MU3D_EP0_STATE_TX;
} else {
- mtu3_writel(mtu->mac_base, U3D_EP0CSR,
- (csr | EP0_SETUPPKTRDY) & (~EP0_DPHTX));
+ mtu3_writel(mtu->mac_base, U3D_EP0CSR, csr & ~EP0_DPHTX);
+ /* send ACK when the buffer is queued */
+ mtu->delayed_setup = 1;
I don't think that you need this variable: you're calling the function
ep0_setup_stage_send_ack() only when ep0_state == MU3D_EP0_STATE_RX in
ep0_queue()...
..so you'll never get a call to ep0_setup_stage_send_ack() with delayed_setup == 0!
Regards,
Angelo
mtu->ep0_state = MU3D_EP0_STATE_RX;
}
}
@@ -804,9 +818,11 @@ static int ep0_queue(struct mtu3_ep *mep, struct mtu3_request *mreq)
switch (mtu->ep0_state) {
case MU3D_EP0_STATE_SETUP:
- case MU3D_EP0_STATE_RX: /* control-OUT data */
case MU3D_EP0_STATE_TX: /* control-IN data */
break;
+ case MU3D_EP0_STATE_RX: /* control-OUT data */
+ ep0_setup_stage_send_ack(mtu);
+ break;
default:
dev_err(mtu->dev, "%s, error in ep0 state %s\n", __func__,
decode_ep0_state(mtu));
