Hi Reinhard:
Although BG95 supports at+qcfgext="usbnet", "rmnet", but lots of QMI message do not support,
E.g WDS_START_NETWORK_INTERFACE, so "rmnet" is basically useless.
On Tuesday, May 17, 2022 at 05:13 AM +0000, Reinhard Speyerer wrote:
> On Mon, May 16, 2022 at 06:10:17AM +0000, Carl Yin(殷张成) wrote:
> > The BG95 modem has 2 USB configurations that are configurable via the
> > AT command AT+QCFGEXT="usbnet",["ecm"|"modem"] which make the
> modem
> > enumerate with the following interfaces, respectively:
> >
> > "modem": Diag + GNSS + Modem + Modem
> > "ecm" : DIAG + GNSS + Modem + ECM
>
> Hi Carl,
>
> what about the AT+QCFGEXT="usbnet","rmnet" configuration available on
> several firmware versions which makes the BG95 enumerate as Diag + GNSS +
> Modem + QMI:
>
> T: Bus=02 Lev=02 Prnt=06 Port=01 Cnt=02 Dev#= 8 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=0700 Rev= 0.00
> S: Manufacturer=Quectel, Incorporated
> S: Product=Quectel LPWA Module
> S: SerialNumber=xxxxxxxx
> C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
> I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
> E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> >
> > A detailed description of the USB configuration for each mode follows:
> >
> > +QCFGEXT: "usbnet","modem"
> > -------------------------
> > T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
> > P: Vendor=2c7c ProdID=0700 Rev= 0.00
> > S: Manufacturer=Quectel, Incorporated
> > S: Product=Quectel LPWA Module
> > S: SerialNumber=884328a2
> > C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
> > I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
> > E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > +QCFGEXT: "usbnet","ecm"
> > -----------------------
> > T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
> > D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> > P: Vendor=2c7c ProdID=0700 Rev= 0.00
> > S: Manufacturer=Quectel, Incorporated
> > S: Product=Quectel LPWA Module
> > S: SerialNumber=884328a2
> > C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
> > A: FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
> > I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> > E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> > E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00
> > Driver=cdc_ether
> > E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
> > I: If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00
> > Driver=cdc_ether
> > I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00
> > Driver=cdc_ether
> > E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> > E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> >
> > Signed-off-by: Carl Yin <carl.yin@xxxxxxxxxxx>
> > ---
> > drivers/usb/serial/option.c | 5 +++++
> > 1 file changed, 5 insertions(+)
> >
> > diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> > index 152ad8826..f91b2a67d 100644
> > --- a/drivers/usb/serial/option.c
> > +++ b/drivers/usb/serial/option.c
> > @@ -256,6 +256,7 @@ static void option_instat_callback(struct urb *urb);
> > #define QUECTEL_PRODUCT_RM500Q 0x0800
> > #define QUECTEL_PRODUCT_EC200S_CN 0x6002
> > #define QUECTEL_PRODUCT_EC200T 0x6026
> > +#define QUECTEL_PRODUCT_BG95 0x0700
> >
> > #define CMOTECH_VENDOR_ID 0x16d8
> > #define CMOTECH_PRODUCT_6001 0x6001
> > @@ -1143,6 +1144,10 @@ static const struct usb_device_id option_ids[] = {
> > .driver_info = ZLP },
> > { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID,
> QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) },
> > { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID,
> > QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) },
> > + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID,
> QUECTEL_PRODUCT_BG95, 0xff, 0xff, 0xff),
> > + .driver_info = ZLP },
>
> Could you please add a RSVD(3) flag to the driver_info here to avoid that the
> option driver incorrectly binds to the QMI interface?
>
> Regards,
> Reinhard
>
> > + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID,
> QUECTEL_PRODUCT_BG95, 0xff, 0xfe, 0xff),
> > + .driver_info = ZLP },
> >
> > { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
> > { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
> > --
> > 2.17.1
> >
