On 11/05/2022 17:26, Krishna Kurapati wrote: > From: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx> > > Add device tree bindings for SNPS phy tuning parameters. > > Signed-off-by: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx> > Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx> > --- > .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 87 ++++++++++++++++++++++ > 1 file changed, 87 insertions(+) > > diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml > index 1ce251d..70efffe 100644 > --- a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml > +++ b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml > @@ -53,6 +53,93 @@ properties: > vdda33-supply: > description: phandle to the regulator 3.3V supply node. > > + qcom,hs-disconnect-bps: > + $ref: /schemas/types.yaml#/definitions/int32 > + description: > + This adjusts the voltage level for the threshold used to > + detect a disconnect event at the host. Possible values are. > + The values defined are in multiples of basis points (1bp = 0.01%). This means there is some minimum and maximum (100%)? > + The hardware accepts only discrete values. The value closest to the > + provided input will be chosen as the override value for this param. > + > + qcom,squelch-detector-bps: > + $ref: /schemas/types.yaml#/definitions/int32 > + description: > + This adjusts the voltage level for the threshold used to > + detect valid high-speed data. > + The values defined are in multiples of basis points (1bp = 0.01%). > + The hardware accepts only discrete values. The value closest to the > + provided input will be chosen as the override value for this param. > + > + qcom,hs-amplitude-bps: > + $ref: /schemas/types.yaml#/definitions/int32 > + description: > + This adjusts the high-speed DC level voltage. > + The values defined are in multiples of basis points (1bp = 0.01%). > + The hardware accepts only discrete values. The value closest to the > + provided input will be chosen as the override value for this param. > + > + qcom,pre-emphasis-duration-bps: > + $ref: /schemas/types.yaml#/definitions/int32 > + description: > + This signal controls the duration for which the > + HS pre-emphasis current is sourced onto DP<#> or DM<#>. > + The HS Transmitter pre-emphasis duration is defined in terms of > + unit amounts. One unit of pre-emphasis duration is approximately > + 650 ps and is defined as 1X pre-emphasis duration. > + The values defined are in multiples of basis points (1bp = 0.01%). > + The hardware accepts only discrete values. The value closest to the > + provided input will be chosen as the override value for this param. > + > + qcom,pre-emphasis-amplitude-bps: > + $ref: /schemas/types.yaml#/definitions/int32 > + description: > + This signal controls the amount of current sourced to > + DP<#> and DM<#> after a J-to-K or K-to-J transition. > + The HS Transmitter pre-emphasis current is defined in terms of unit > + amounts. One unit amount is approximately 2 mA and is defined as > + 1X pre-emphasis current. > + The values defined are in multiples of basis points (1bp = 0.01%). > + The hardware accepts only discrete values. The value closest to the > + provided input will be chosen as the override value for this param. > + > + qcom,hs-rise-fall-time-bps: > + $ref: /schemas/types.yaml#/definitions/int32 > + description: > + This adjusts the rise/fall times of the high-speed waveform. > + The values defined are in multiples of basis points (1bp = 0.01%). > + The hardware accepts only discrete values. The value closest to the > + provided input will be chosen as the override value for this param. > + > + qcom,hs-crossover-voltage-mv: > + $ref: /schemas/types.yaml#/definitions/int32 > + description: > + This adjusts the voltage at which the DP<#> and DM<#> > + signals cross while transmitting in HS mode. > + The values defined are in milli volts. The hardware accepts only > + discrete values. The value closest to the provided input will be > + chosen as the override value for this param. > + > + qcom,hs-output-impedance-mohm: > + $ref: /schemas/types.yaml#/definitions/int32 Here and in other places, please use standard units. See dtschema/schemas/property-units.yaml in dtschema repo. Best regards, Krzysztof
