Re: [PATCH 18/48] ARM: pxa: hx4700: use gpio descriptors for audio

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, May 4, 2022 at 11:59 PM Linus Walleij <linus.walleij@xxxxxxxxxx> wrote:
> On Mon, May 2, 2022 at 9:08 AM Arnd Bergmann <arnd@xxxxxxxxxx> wrote:
> > On Sun, May 1, 2022 at 11:41 PM Linus Walleij <linus.walleij@xxxxxxxxxx> wrote:
> > >
> > > (...)
> > > > +static struct gpiod_lookup_table hx4700_audio_gpio_table = {
> > > > +       .dev_id = "hx4700-audio",
> > > > +       .table = {
> > > > +               GPIO_LOOKUP("gpio-pxa", GPIO75_HX4700_EARPHONE_nDET,
> > > > +                           "earphone-ndet", GPIO_ACTIVE_HIGH),
> > >
> > > This looks wrong. The n in nDET in the end of the name of the GPIO line
> > > means active low does it not?
> > >
> > > What I usually do when I see this is to properly set it to
> > > GPIO_ACTIVE_LOW in the descriptor table, then invert the logic
> > > where it's getting used.
> > >
> > > Also rename to earphone-det instead of -ndet
> >
> > Thanks for taking a look! I changed it now, but I don't know if
> > I got the correct number of inversions in the end. How does this look?
>
> Looks wrong, you can just invert the argument to any statement of set_value()
> after tagging respective line as active low. Then gpilob will do a second
> inversion.
>
> > +               GPIO_LOOKUP("gpio-pxa", GPIO75_HX4700_EARPHONE_nDET,
> > +                           "earphone-det", GPIO_ACTIVE_LOW),
> > +               GPIO_LOOKUP("gpio-pxa", GPIO107_HX4700_SPK_nSD,
> > +                           "spk-sd", GPIO_ACTIVE_LOW),
>
> So those two have switched polarity.
>
> > @@ -81,14 +79,14 @@ static const struct snd_soc_ops hx4700_ops = {
> >  static int hx4700_spk_power(struct snd_soc_dapm_widget *w,
> >                             struct snd_kcontrol *k, int event)
> >  {
> > -       gpio_set_value(GPIO107_HX4700_SPK_nSD, !!SND_SOC_DAPM_EVENT_ON(event));
> > +       gpiod_set_value(gpiod_spk_sd, !!SND_SOC_DAPM_EVENT_ON(event));
>
> Thus drop one ! in front of the expression, just !SND_SOC_DAPM_EVENT_ON(event)

Ok, done. But I still leave the extra 'invert=1' in hs_jack_pin[], right?

/* Headphones jack detection DAPM pin */
static struct snd_soc_jack_pin hs_jack_pin[] = {
        {
                .pin    = "Headphone Jack",
                .mask   = SND_JACK_HEADPHONE,
        },
        {
                .pin    = "Speaker",
                /* disable speaker when hp jack is inserted */
                .mask   = SND_JACK_HEADPHONE,
                .invert = 1,
        },
};

> > +       gpiod_spk_sd = devm_gpiod_get(&pdev->dev, "spk-sd", GPIOD_OUT_LOW);
>
> These initial values don't seem to be set in the old code you could
> just use GPIOD_ASIS as flag to make sure the new code behaves
> the same.

Ok.

        Arnd



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux