Hi Heikki,
On Thu, Mar 31, 2022 at 02:16:53PM +0300, Heikki Krogerus wrote:
> On Wed, Mar 30, 2022 at 08:47:34PM +0300, Mathias Nyman wrote:
> > On 29.3.2022 12.18, Sandeep Maheswaram (Temp) wrote:
> > > Hi Mathias,Heikki
> > >
> > > On 3/25/2022 9:08 PM, Heikki Krogerus wrote:
> > >> On Fri, Mar 25, 2022 at 04:33:27PM +0200, Mathias Nyman wrote:
> > >>> On 25.3.2022 13.27, Heikki Krogerus wrote:
> > >>>> On Fri, Mar 25, 2022 at 12:36:22AM +0200, Mathias Nyman wrote:
> > >>>>> On 24.3.2022 14.27, Heikki Krogerus wrote:
> > >>>>>> On Thu, Mar 24, 2022 at 12:07:11PM +0530, Sandeep Maheswaram wrote:
> > >>>>>>> Currently the phy init is done from dwc3 and also xhci which makes the
> > >>>>>>> runtime_usage value 2 for the phy which causes issue during runtime
> > >>>>>>> suspend. When we run the below command the runtime_status still shows
> > >>>>>>> active.
> > >>>>>>> echo auto > /sys/bus/platform/devices/88e3000.phy/power/control
> > >>>>>>>
> > >>>>>>> dwc3 manages PHY by own DRD driver, so skip the management by
> > >>>>>>> HCD core by setting this quirk.
> > >>>>>>>
> > >>>>>>> Signed-off-by: Sandeep Maheswaram <quic_c_sanm@xxxxxxxxxxx>
> > >>>>>>> ---
> > >>>>>>> drivers/usb/dwc3/host.c | 13 +++++++++++++
> > >>>>>>> 1 file changed, 13 insertions(+)
> > >>>>>>>
> > >>>>>>> diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
> > >>>>>>> index eda8719..d4fcf06 100644
> > >>>>>>> --- a/drivers/usb/dwc3/host.c
> > >>>>>>> +++ b/drivers/usb/dwc3/host.c
> > >>>>>>> @@ -13,6 +13,12 @@
> > >>>>>>> #include <linux/platform_device.h>
> > >>>>>>> #include "core.h"
> > >>>>>>> +#include <linux/usb/xhci-plat.h>
> > >>>>>>> +#include <linux/usb/xhci-quirks.h>
> > >>>>>>> +
> > >>>>>>> +static const struct xhci_plat_priv xhci_plat_dwc3_xhci = {
> > >>>>>>> + .quirks = XHCI_SKIP_PHY_INIT,
> > >>>>>>> +};
> > >>>>>>> static void dwc3_host_fill_xhci_irq_res(struct dwc3 *dwc,
> > >>>>>>> int irq, char *name)
> > >>>>>>> @@ -122,6 +128,13 @@ int dwc3_host_init(struct dwc3 *dwc)
> > >>>>>>> }
> > >>>>>>> }
> > >>>>>>> + ret = platform_device_add_data(xhci, &xhci_plat_dwc3_xhci,
> > >>>>>>> + sizeof(xhci_plat_dwc3_xhci));
> > >>>>>>> + if (ret) {
> > >>>>>>> + dev_err(dwc->dev, "failed to add data to xHCI\n");
> > >>>>>>> + goto err;
> > >>>>>>> + }
> > >>>>>>> +
> > >>>>>>> ret = platform_device_add(xhci);
> > >>>>>>> if (ret) {
> > >>>>>>> dev_err(dwc->dev, "failed to register xHCI device\n");
> > >>>>>> I think you should just use device property:
> > >>>>>>
> > >>>>> This was suggested in an earlier series, but was rejected as it also added
> > >>>>> the property as a device tree parameter.
> > >>>>>
> > >>>>> I think adding more device properties can be messy in the long run, especially if we
> > >>>>> need to add them for many of the existing xhci quirks.
> > >>>>> We also end up with a mix where some device properties are listed as device tree
> > >>>>> parameters, and some not.
> > >>>>>
> > >>>>> Defining xhci quirks and platform data structure in headers shared with dwc3 and cdns3
> > >>>>> allow those drivers to easily set any existing xhci quirk, or other possible optional
> > >>>>> callbacks.
> > >>>>>
> > >>>>> cdns3 driver is already doing this, but it includes the full xhci.h header.
> > >>>>> This series cleans up that a bit so cdns3 will only include xhci quirk bits and
> > >>>>> platform data structure.
> > >>>>>
> > >>>>> On the downside we add a couple xhci related header files to include/linux/usb/
> > >>>>> Let me know if you see any other issues I missed with this approach.
> > >>>> The problem here is that these drivers are now coupled together, and
> > >>>> that should not be taken lightly. We have a dependency hell in our
> > >>>> hands with a lot of drivers, and the culprit is always platform data.
> > >>>>
> > >>>> Build-in device properties may be messy, but I would still say they
> > >>>> are less messy than those quirk flags - you got to admit, they are a
> > >>>> mess. The benefit from build-in properties is in any case the fact
> > >>>> that they remove the need to couple these drivers together.
> > >>> Agree, quirk bits are messy. Any suggestion that would work with
> > >>> PCI xHCI devices, devicetree, and "pure" platform devices?
> > >> I think xHCI driver should always be able to rely on being able to
> > >> read this kind of information from the fwnode. If there is no actual
> > >> firmware node (DT or ACPI), or if it's missing some information, the
> > >> glue driver needs to populate software node for the xHCI.
> > >>
> > >> Right now I just want to avoid having to pass the quirks using
> > >> platform data from drivers such as drivers/usb/cdns3/host.c and
> > >> drivers/usb/dwc3/host.c to xHCI.
> > >>
> > >> One way we could do that is by defining compatibility ID for both of
> > >> them that we provide using a single device property (like I guess DT
> > >> does). Then based on that compatibility ID, xhci-plat.c can set the
> > >> actual "static" quirk flags. That we could already do easily. How
> > >> would that sound to you?
> >
> > Sounds good.
> >
> > >
> > > This was my previous patch where I was using device tree property. Should we go ahead with this approach?
> > >
> > > https://patchwork.kernel.org/project/linux-arm-msm/cover/1636353710-25582-1-git-send-email-quic_c_sanm@xxxxxxxxxxx/
> > >
> > > Any further changes to this ?
> >
> > By dropping the DT part of that series we get a similar built-in device property
> > solution as Heikki initially suggested.
> >
> > How about adding the compatibility ID device property that was just suggested?
> > Then matching the Id in xhci-plat.c against a static table containing Ids and
> > xhci_plat_priv structures, with the needed quirks for dwc3.
>
> There was a comment from Pavan. Is it still possible to get this
> detail from DT?
> I guess that would still be ideal, right?
>
I was suggesting if we can have device tree param like the patch sandeep
pointed out.
How would adding a compatible index to usb_xhci_of_match[] would work
actually? I ask this because, dwc3/host.c creates platform device and
it is not associated with any of_node, so of_driver_match_device() called
from platform bus match method does not work. one way to achieve this would
be by matching against sysdev. Something like below. Is it acceptible?
diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
index 649ffd8..bd5d055 100644
--- a/drivers/usb/host/xhci-plat.c
+++ b/drivers/usb/host/xhci-plat.c
@@ -126,6 +126,10 @@ static const struct xhci_plat_priv xhci_plat_brcm = {
.quirks = XHCI_RESET_ON_RESUME,
};
+static const struct xhci_plat_priv xhci_plat_dwc3 = {
+ .quirks = XHCI_SKIP_PHY_INIT,
+};
+
static const struct of_device_id usb_xhci_of_match[] = {
{
.compatible = "generic-xhci",
@@ -167,6 +171,9 @@ static const struct of_device_id usb_xhci_of_match[] = {
}, {
.compatible = "brcm,bcm7445-xhci",
.data = &xhci_plat_brcm,
+ }, {
+ .compatible = "snps,dwc3",
+ .data = &xhci_plat_dwc3,
},
{},
};
@@ -274,6 +281,15 @@ static int xhci_plat_probe(struct platform_device *pdev)
else
priv_match = dev_get_platdata(&pdev->dev);
+ /* allow private data mapping with the sysdev compatible */
+ if (!priv_match) {
+ struct of_device_id *match;
+
+ match = of_match_device(usb_xhci_of_match, sysdev);
+ if (match)
+ priv_match = match->data;
+ }
+
if (priv_match) {
priv = hcd_to_xhci_priv(hcd);
/* Just copy data for now */
> I have another question. Can't we now just assume that if the sysdev
> is the parent (or grandparent), then the phy initialization should
> always be skipped? In that case we could just do something like this:
>
> diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
> index 649ffd861b44e..1018b33488046 100644
> --- a/drivers/usb/host/xhci-plat.c
> +++ b/drivers/usb/host/xhci-plat.c
> @@ -212,8 +212,12 @@ static int xhci_plat_probe(struct platform_device *pdev)
> #endif
> }
>
> - if (!sysdev)
> + if (sysdev) {
> + if (sysdev != &pdev->dev)
> + hcd->skip_phy_initialization = 1;
> + } else {
> sysdev = &pdev->dev;
> + }
>
> if (WARN_ON(!sysdev->dma_mask))
> /* Platform did not initialize dma_mask */
>
>
> I did not go through all the drivers that carefully, so I may have
> missed something, but it looks like the only drivers that can have the
> sysdev as the parent or grandparent are cdns3 and dwc3.
>
I cross checked and these are two drivers that are creating xhci-plat device.
So this patch would definitely work. However I am not sure in future if any
device created via device tree would want to use this feature. For now,
it looks good. It Mathias, Do you see any problem with this approach?
Thanks,
Pavan
