Hi Thinh,
On 3/23/2022 5:39 PM, Thinh Nguyen wrote:
> Hi Wesley,
>
> Wesley Cheng wrote:
>> Hi Thinh,
>>
>> On 3/22/2022 6:31 PM, Thinh Nguyen wrote:
>>> Hi Wesley,
>>>
>>> Wesley Cheng wrote:
>>>> Hi Thinh,
>>>>
>>>> On 2/15/2022 4:08 PM, Wesley Cheng wrote:
>>>>> While running the pullup disable sequence, if there are pending SETUP
>>>>> transfers stored in the controller, then the ENDTRANSFER commands on non
>>>>> control eps will fail w/ ETIMEDOUT. As a suggestion from SNPS, in order
>>>>> to drain potentially cached SETUP packets, SW needs to issue a
>>>>> STARTTRANSFER command. After issuing the STARTTRANSFER, and retrying the
>>>>> ENDTRANSFER, the command should succeed. Else, if the endpoints are not
>>>>> properly stopped, the controller halt sequence will fail as well.
>>>>>
>>>>> One limitation is that the current logic will drop the SETUP data
>>>>> being received (ie dropping the SETUP packet), however, it should be
>>>>> acceptable in the pullup disable case, as the device is eventually
>>>>> going to disconnect from the host.
>>>>>
>>>>> Signed-off-by: Wesley Cheng <quic_wcheng@xxxxxxxxxxx>
>>>>> ---
>>>> Just wondering if you had any inputs for this particular change? I
>>>> think on the dequeue path discussion you had some concerns with parts of
>>>> this change? I think the difficult part for the pullup disable path is
>>>> that we have this API running w/ interrupts disabled, so the EP0 state
>>>> won't be able to advance compared to the dequeue case.
>>>
>>> This doesn't sound right. The pullup disable (or device initiated
>>> disconnect) should wait for the EP0 state to be EP0_SETUP_PHASE before
>>> proceeding, which it does.
>>>
>> That is correct, but even though that check is passed, it doesn't
>> prevent the host from sending another SETUP token between the pending
>> setup packet check and run/stop clear.
>>
>
> That should be fine, because we would have the TRB ready for that SETUP
> packet.
>
I agree, its valid for the controller to be able to receive the next
setup packet.
>>>>
>>>> Ideally, if there is a way to ensure that we avoid reading further setup
>>>> packets, that would be nice, but from our discussions with Synopsys,
>>>> this was not possible. (controller is always armed and ready to ACK
>>>> setup tokens)
>>>>
>>>> I did evaluate keeping IRQs enabled and periodically releasing/attaining
>>>> the lock between the stop active xfer calls, but that opened another can
>>>> of worms. If you think this is the approach we should take, I can take
>>>> a look at this implementation further.
>>>>
>>>
>>> This patch doesn't look right to me. The change I suggested before
>>> should address this (I believe Greg already picked it up). What other
>>> problem do you see, I'm not clear what's the problem here. One potential
>>> problem that I can see is that currently dwc3 driver doesn't wait for
>>> active endpoints to complete/end before clearing the run_stop bit on
>>> device initiated disconnect, but I'm not sure if that's what you're seeing.
>>>
>>> Please help clarify further. If there's trace points log, that'd help.
>>>
>> Main difference between the issue Greg recently pulled in and this one
>> is that this is on the pullup disable patch (no dequeue involved). In
>> this situation we will also stop active transfers, so that the
>> controller can halt properly.
>>
>> I attached a few files, and will give a summary of them below:
>> 1. pullup_disable_timeout.txt - ftrace of an instance of when we see
>> several endxfer timeouts. Refer to line#2016.
>>
>> 2. lecroy+ftrace_snip.png - picture showing a matching bus sniffer log
>> and a ftrace collected (difference instance to #1)
>>
>> #2 will show that we completed a SETUP transfer before entering into
>> dwc3_gadget_stop_active_transfers(). In here, we then see DWC ACK
>> another SETUP token, which leads to endxfer timeouts on all subsequent
>> endpoints.
>
> Thanks for the captures. I think the problem here is because the dwc3
> driver disables the control endpoint. It shouldn't do that.
>
> Can you try this:
>
> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
> index ab725d2262d6..f0b9ea353620 100644
> --- a/drivers/usb/dwc3/gadget.c
> +++ b/drivers/usb/dwc3/gadget.c
> @@ -1010,12 +1010,12 @@ static int __dwc3_gadget_ep_disable(struct
> dwc3_ep *dep)
> if (dep->flags & DWC3_EP_STALL)
> __dwc3_gadget_ep_set_halt(dep, 0, false);
>
> - reg = dwc3_readl(dwc->regs, DWC3_DALEPENA);
> - reg &= ~DWC3_DALEPENA_EP(dep->number);
> - dwc3_writel(dwc->regs, DWC3_DALEPENA, reg);
> -
> - /* Clear out the ep descriptors for non-ep0 */
> if (dep->number > 1) {
> + reg = dwc3_readl(dwc->regs, DWC3_DALEPENA);
> + reg &= ~DWC3_DALEPENA_EP(dep->number);
> + dwc3_writel(dwc->regs, DWC3_DALEPENA, reg);
> +
> + /* Clear out the ep descriptors for non-ep0 */
> dep->endpoint.comp_desc = NULL;
> dep->endpoint.desc = NULL;
> }
>
I was able to reproduce the endxfer timeout w/ the above change. I'm
assuming you didn't want me to include any parts of my change while
testing, right?
Current sequence in dwc3_gadget_pullup(0) is that we should call
dwc3_stop_active_transfers() before we call __dwc3_gadget_stop().
(gadget stop will call the ep disable for EP[0] and EP[1]) This might
be why the issue would still be occurring.
The attached ftrace that captures a situation where a forced BUG will
occur on the first instance of the timeout.
[ 1573.687689437 0x724885c22] event (000020c0): ep0out: Transfer
Not Ready [0] (Not Active) [Status Phase]
[ 1573.687738707 0x724885fd3] dbg_send_ep_cmd: ep0out: cmd
'Start Transfer' [406] params 00000000 efffa000 00000000 --> status:
Successful
[ 1573.698040582 0x7248b6477] dbg_send_ep_cmd: ep1out: cmd 'End
Transfer' [20c08] params 00000000 00000000 00000000 --> status: Timed Out
We definitely started the STATUS phase, so host could have read it and
sent the next SETUP packet while we were already in the
dwc3_stop_active_transfers() loop.
Thanks
Wesley Cheng[ 1573.453509905 0x72443c0ab] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.453581207 0x72443c603] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.453674696 0x72443cd06] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.453751832 0x72443d2d0] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.453847040 0x72443d9f3] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.453875998 0x72443dc20] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 4)
[ 1573.453973967 0x72443e378] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.454006467 0x72443e5e8] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.454101988 0x72443ed12] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.454187405 0x72443f37b] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.454211467 0x72443f549] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.454282144 0x72443fa96] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.454500217 0x724440af1] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.454578134 0x7244410c9] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.454675113 0x72444180f] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.454706988 0x724441a73] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 18)
[ 1573.454810530 0x724442237] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.454843446 0x7244424ae] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.454943342 0x724442c2c] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.455030321 0x7244432b3] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 zsI ==> 0
[ 1573.455053655 0x724443472] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.455124696 0x7244439c7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.455219071 0x7244440da] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.455298134 0x7244446c9] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.455392769 0x724444de2] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.455423446 0x72444502e] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 4)
[ 1573.455523915 0x7244457b7] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.455557248 0x724445a38] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.455658342 0x7244461cd] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.455742144 0x724446816] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.455764696 0x7244469c6] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.455837144 0x724446f35] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.455935009 0x72444768c] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.456016363 0x724447ca6] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.456113759 0x7244483f5] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.456144384 0x724448640] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 48)
[ 1573.456243655 0x724448db3] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.456276519 0x724449029] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.456374488 0x724449782] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.456460061 0x724449dee] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 48/48 zsI ==> 0
[ 1573.456483238 0x724449fab] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.456559019 0x72444a559] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.456654800 0x72444ac88] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.456734228 0x72444b27d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.456945373 0x72444c254] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.456977665 0x72444c4c0] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 4)
[ 1573.457080946 0x72444cc7f] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.457114019 0x72444cefa] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.457214228 0x72444d67e] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.457299019 0x72444dcd9] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.457321780 0x72444de8f] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.457394228 0x72444e3fd] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.457492769 0x72444eb62] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.457572509 0x72444f15d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.457665998 0x72444f860] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.457696050 0x72444faa1] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 18)
[ 1573.457795530 0x724450217] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.457827665 0x72445047f] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.457927144 0x724450bf6] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.458010894 0x72445123e] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 zsI ==> 0
[ 1573.458033238 0x7244513ea] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.458105113 0x72445194f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.458301155 0x724452803] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.458382300 0x724452e19] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.459751103 0x7244594c1] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.459783498 0x724459730] dbg_trace_log_ctrl: Set Configuration(Config = 1)
[ 1573.460083186 0x72445ada9] dbg_send_ep_cmd: ep1out: cmd 'Set Endpoint Configuration' [401] params 00001004 04000200 00000000 --> status: Successful
[ 1573.460157613 0x72445b33f] dbg_send_ep_cmd: ep1out: cmd 'Start Transfer' [406] params 00000000 efff8000 00000000 --> status: Successful
[ 1573.460243863 0x72445b9b7] dbg_send_ep_cmd: ep1in: cmd 'Set Endpoint Configuration' [401] params 00021004 06000200 00000000 --> status: Successful
[ 1573.460316780 0x72445bf2f] dbg_send_ep_cmd: ep1in: cmd 'Start Transfer' [406] params 00000000 efff7000 00000000 --> status: Successful
[ 1573.460471936 0x72445cad2] dbg_send_ep_cmd: ep3in: cmd 'Set Endpoint Configuration' [401] params 00060056 0e080200 00000000 --> status: Successful
[ 1573.460543290 0x72445d02c] dbg_send_ep_cmd: ep3in: cmd 'Start Transfer' [406] params 00000000 efff3000 00000000 --> status: Successful
[ 1573.460617509 0x72445d5bd] dbg_send_ep_cmd: ep2in: cmd 'Set Endpoint Configuration' [401] params 00041004 0a000200 00000000 --> status: Successful
[ 1573.460684436 0x72445dac1] dbg_send_ep_cmd: ep2in: cmd 'Start Transfer' [406] params 00000000 efff5000 00000000 --> status: Successful
[ 1573.460747665 0x72445df80] dbg_send_ep_cmd: ep2out: cmd 'Set Endpoint Configuration' [401] params 00001004 08000200 00000000 --> status: Successful
[ 1573.460817405 0x72445e4bb] dbg_send_ep_cmd: ep2out: cmd 'Start Transfer' [406] params 00000000 efff6000 00000000 --> status: Successful
[ 1573.460924332 0x72445ecc0] dbg_ep_queue: ep2out: req ffffff87a162f100 length 0/2048 zsI ==> -115
[ 1573.460975061 0x72445f08e] dbg_prepare: ep2out: trb ffffffc01e3b7000 (E1:D0) buf 00000000ed67d800 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461032300 0x72445f4d9] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461071050 0x72445f7c1] dbg_ep_queue: ep2out: req ffffff87a162ef00 length 0/2048 zsI ==> -115
[ 1573.461112665 0x72445fae0] dbg_prepare: ep2out: trb ffffffc01e3b7010 (E2:D0) buf 00000000ed2bf000 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461166571 0x72445feeb] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461201623 0x72446018c] dbg_ep_queue: ep2out: req ffffff87a4f4c700 length 0/2048 zsI ==> -115
[ 1573.461230373 0x7244603b4] dbg_prepare: ep2out: trb ffffffc01e3b7020 (E3:D0) buf 00000000ed0eb000 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461287196 0x7244607f6] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461321571 0x724460a8a] dbg_ep_queue: ep2out: req ffffff87a1f87600 length 0/2048 zsI ==> -115
[ 1573.461350790 0x724460cbc] dbg_prepare: ep2out: trb ffffffc01e3b7030 (E4:D0) buf 00000000ecff9000 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461406780 0x7244610ef] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461441259 0x724461385] dbg_ep_queue: ep2out: req ffffff8896b56700 length 0/2048 zsI ==> -115
[ 1573.461480009 0x72446166d] dbg_prepare: ep2out: trb ffffffc01e3b7040 (E5:D0) buf 00000000ee2f7800 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461537665 0x724461ac0] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461572665 0x724461d5f] dbg_ep_queue: ep2out: req ffffff8896b57500 length 0/2048 zsI ==> -115
[ 1573.461601259 0x724461f84] dbg_prepare: ep2out: trb ffffffc01e3b7050 (E6:D0) buf 00000000efaf0800 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461655113 0x72446238f] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461689123 0x72446261b] dbg_ep_queue: ep2out: req ffffff8040b28800 length 0/2048 zsI ==> -115
[ 1573.461716623 0x72446282c] dbg_prepare: ep2out: trb ffffffc01e3b7060 (E7:D0) buf 00000000ed0ec000 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461770842 0x724462c3d] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461805217 0x724462ed1] dbg_ep_queue: ep2out: req ffffff889686ad00 length 0/2048 zsI ==> -115
[ 1573.461832509 0x7244630dd] dbg_prepare: ep2out: trb ffffffc01e3b7070 (E8:D0) buf 00000000ed0ed000 size 2048 ctrl 00000819 (HlcS:sC:normal)
[ 1573.461885373 0x7244634d4] dbg_send_ep_cmd: ep2out: cmd 'Update Transfer' [40007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.461965894 0x724463ade] dbg_send_ep_cmd: ep5in: cmd 'Set Endpoint Configuration' [401] params 000a0046 16080200 00000000 --> status: Successful
[ 1573.462034332 0x724463fff] dbg_send_ep_cmd: ep5in: cmd 'Start Transfer' [406] params 00000000 ed5ff000 00000000 --> status: Successful
[ 1573.462090686 0x72446443a] dbg_ep_queue: ep1out: req ffffff87b7e41c00 length 0/16384 zsI ==> -115
[ 1573.462156259 0x724464925] dbg_prepare: ep1out: trb ffffffc01e3ad000 (E1:D0) buf 00000000ecee0000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.462216363 0x724464da7] dbg_send_ep_cmd: ep1out: cmd 'Update Transfer' [20007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.462285842 0x7244652dc] dbg_send_ep_cmd: ep7in: cmd 'Set Endpoint Configuration' [401] params 000e1004 1e000200 00000000 --> status: Successful
[ 1573.462354488 0x724465802] dbg_send_ep_cmd: ep7in: cmd 'Start Transfer' [406] params 00000000 effeb000 00000000 --> status: Successful
[ 1573.462446155 0x724465ee3] dbg_send_ep_cmd: ep4out: cmd 'Set Endpoint Configuration' [401] params 00001004 10000200 00000000 --> status: Successful
[ 1573.462515582 0x724466417] dbg_send_ep_cmd: ep4out: cmd 'Start Transfer' [406] params 00000000 ecff7000 00000000 --> status: Successful
[ 1573.462591467 0x7244669c8] dbg_send_ep_cmd: ep8in: cmd 'Set Endpoint Configuration' [401] params 00101004 22000200 00000000 --> status: Successful
[ 1573.462659592 0x724466ee4] dbg_send_ep_cmd: ep8in: cmd 'Start Transfer' [406] params 00000000 effe9000 00000000 --> status: Successful
[ 1573.462842092 0x724467c94] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.465300842 0x7244734fc] dbg_ep_queue: ep4out: req ffffff87a6768e00 length 0/16384 zsI ==> -115
[ 1573.465345582 0x724473857] dbg_prepare: ep4out: trb ffffffc05a98d000 (E1:D0) buf 00000000ed2e8000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.465404071 0x724473cba] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.465575009 0x72447498d] dbg_ep_queue: ep4out: req ffffff87a6768c00 length 0/16384 zsI ==> -115
[ 1573.465606623 0x724474bec] dbg_prepare: ep4out: trb ffffffc05a98d010 (E2:D0) buf 00000000ed2e4000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.465662300 0x724475019] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.465837873 0x724475d43] dbg_ep_queue: ep4out: req ffffff87a6768900 length 0/16384 zsI ==> -115
[ 1573.465884540 0x7244760c4] dbg_prepare: ep4out: trb ffffffc05a98d020 (E3:D0) buf 00000000ee1c8000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.465943498 0x72447652f] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.466121832 0x724477290] dbg_ep_queue: ep4out: req ffffff8860a95300 length 0/16384 zsI ==> -115
[ 1573.466152300 0x7244774d9] dbg_prepare: ep4out: trb ffffffc05a98d030 (E4:D0) buf 00000000ee1cc000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.466210009 0x72447792d] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.467284905 0x72447c9ca] dbg_ep_queue: ep4out: req ffffff87c93b0800 length 0/16384 zsI ==> -115
[ 1573.467317144 0x72447cc35] dbg_prepare: ep4out: trb ffffffc05a98d040 (E5:D0) buf 00000000ee128000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.467373655 0x72447d073] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.467544540 0x72447dd44] dbg_ep_queue: ep4out: req ffffff87837a2700 length 0/16384 zsI ==> -115
[ 1573.467575738 0x72447df9b] dbg_prepare: ep4out: trb ffffffc05a98d050 (E6:D0) buf 00000000efe40000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.467630373 0x72447e3b4] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.467794696 0x72447f006] dbg_ep_queue: ep4out: req ffffff886706cd00 length 0/16384 zsI ==> -115
[ 1573.467837978 0x72447f345] dbg_prepare: ep4out: trb ffffffc05a98d060 (E7:D0) buf 00000000eed7c000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.467892978 0x72447f766] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.468065582 0x724480458] dbg_ep_queue: ep4out: req ffffff886706c600 length 0/16384 zsI ==> -115
[ 1573.468097248 0x7244806b8] dbg_prepare: ep4out: trb ffffffc05a98d070 (E8:D0) buf 00000000efa00000 size 16384 ctrl 00000819 (HlcS:sC:normal)
[ 1573.468153498 0x724480aef] dbg_send_ep_cmd: ep4out: cmd 'Update Transfer' [80007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.500790946 0x724519abf] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.500972196 0x72451a857] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.501025478 0x72451ac55] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 0/0 zsI ==> 0
[ 1573.501103186 0x72451b229] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.502366051 0x7245210e1] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.502401936 0x724521392] dbg_trace_log_ctrl: Clear Device Feature(Self Powered)
[ 1573.502527353 0x724521cf9] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.502563707 0x724521fb4] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.502659228 0x7245226de] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.502740894 0x724522cfd] dbg_gadget_giveback: ep0out: req ffffff87a6768700 length 16/16 zsI ==> 0
[ 1573.502764280 0x724522ebf] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.502833290 0x7245233ec] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.502921936 0x724523a92] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.502995217 0x724524011] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.503084124 0x7245246bc] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.503115165 0x72452490f] dbg_trace_log_ctrl: Clear Device Feature(Self Powered)
[ 1573.503198030 0x724524f46] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.503229019 0x72452519a] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.503320790 0x72452587b] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.503384749 0x724525d48] dbg_gadget_giveback: ep0out: req ffffff87a6768700 length 64/64 zsI ==> 0
[ 1573.503407144 0x724525ef6] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.503474749 0x724526408] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.503564228 0x724526abe] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.503642092 0x724527095] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.505121103 0x72452df82] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.505155894 0x72452e21e] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 4)
[ 1573.505246467 0x72452e8e9] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.505278134 0x72452eb49] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.505376467 0x72452f2a8] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.505405894 0x72452f4de] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.505471103 0x72452f9c1] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.505493394 0x72452fb6d] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.505563082 0x7245300a7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.505656363 0x7245307a6] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.505734332 0x724530d80] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.505829124 0x72453149c] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.505859436 0x7245316e2] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 48)
[ 1573.505943030 0x724531d27] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.505975946 0x724531f9f] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.506071103 0x7245326c1] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.506135634 0x724532b98] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 48/48 zsI ==> 0
[ 1573.506158082 0x724532d47] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.506230634 0x7245332b9] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.506437613 0x72453423e] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.506516259 0x724534824] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.510395321 0x724546b13] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.510433082 0x724546de8] dbg_trace_log_ctrl: Get Device Qualifier Descriptor(Index = 0, Length = 10)
[ 1573.510519957 0x72454746b] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.510553082 0x7245476e8] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.510653446 0x724547e6f] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.510718446 0x72454834f] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 10/10 zsI ==> 0
[ 1573.510741311 0x724548505] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.510812613 0x724548a5e] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.510906259 0x724549164] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.510983446 0x72454972f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.511079019 0x724549e59] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.511110842 0x72454a0bd] dbg_trace_log_ctrl: Get Other Speed Config Descriptor(Index = 0, Length = 9)
[ 1573.511202092 0x72454a794] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.511234436 0x72454aa01] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.511330374 0x72454b134] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.511359905 0x72454b36b] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.511424071 0x72454b83b] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 9/9 zsI ==> 0
[ 1573.511446467 0x72454b9e8] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.511517509 0x72454bf3d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.511610582 0x72454c638] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.511689436 0x72454cc22] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.511788238 0x72454d38b] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.511817717 0x72454d5c1] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 4)
[ 1573.511904176 0x72454dc3d] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.511935738 0x72454de9b] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.512033238 0x72454e5eb] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.512097717 0x72454eac0] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.512120686 0x72454ec79] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.512191780 0x72454f1cf] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.512285165 0x72454f8cf] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.512360790 0x72454fe7b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.512456051 0x7245505a0] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.512488082 0x724550807] dbg_trace_log_ctrl: Get Other Speed Config Descriptor(Index = 0, Length = 166)
[ 1573.512572509 0x724550e5c] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.512604332 0x7245510c0] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.512700321 0x7245517f2] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.512764540 0x724551cc4] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 166/166 zsI ==> 0
[ 1573.512788238 0x724551e8b] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.512857457 0x7245523bc] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.512949019 0x724552a9a] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.513025426 0x724553054] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.513115738 0x72455371b] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.513147040 0x724553974] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 48)
[ 1573.513230165 0x724553fb0] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.513261051 0x724554201] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.513351728 0x7245548ce] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.513415999 0x724554da0] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 48/48 zsI ==> 0
[ 1573.513438134 0x724554f49] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.513506311 0x724555466] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.513595686 0x724555b1a] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.513668811 0x724556096] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.513757353 0x724556739] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.513788499 0x724556990] dbg_trace_log_ctrl: Get String Descriptor(Index = 0, Length = 510)
[ 1573.513874749 0x724557008] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.513905686 0x724557259] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.513997665 0x724557940] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.514061103 0x724557e01] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 ZsI ==> 0
[ 1573.514083551 0x724557fb0] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.514152092 0x7245584d5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.514328915 0x724559218] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.514406415 0x7245597e7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.514603967 0x72455a6b8] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.514636571 0x72455a92b] dbg_trace_log_ctrl: Get String Descriptor(Index = 1, Length = 510)
[ 1573.514720999 0x72455af80] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.514752613 0x72455b1df] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.514845269 0x72455b8d1] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.514911363 0x72455bdc7] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 ZsI ==> 0
[ 1573.514934749 0x72455bf88] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.515005842 0x72455c4dd] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.515097353 0x72455cbba] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.515173655 0x72455d173] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.515468707 0x72455e794] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.515503238 0x72455ea2a] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 510)
[ 1573.515591624 0x72455f0cc] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.515623238 0x72455f32b] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.515717926 0x72455fa45] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.515786103 0x72455ff62] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 48/48 ZsI ==> 0
[ 1573.515809280 0x72456011f] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.515881832 0x72456068f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.515975426 0x724560d95] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.516051676 0x72456134d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.516554488 0x724563903] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.516587769 0x724563b82] dbg_trace_log_ctrl: Get String Descriptor(Index = 4, Length = 510)
[ 1573.516672353 0x7245641da] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.516704280 0x72456443f] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.516798134 0x724564b48] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.516863238 0x72456502a] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 72/72 ZsI ==> 0
[ 1573.516885738 0x7245651db] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.516955894 0x72456571e] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.517050999 0x724565e3f] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.517126624 0x7245663ec] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.517330217 0x724567330] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.517363811 0x7245675b6] dbg_trace_log_ctrl: Get String Descriptor(Index = 6, Length = 510)
[ 1573.517453446 0x724567c6f] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.517486051 0x724567ee1] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.517582613 0x72456861f] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.517649124 0x724568b1c] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 12/12 ZsI ==> 0
[ 1573.517671936 0x724568cd1] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.517744957 0x72456924b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.517838811 0x724569956] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.517916415 0x724569f27] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.518118030 0x72456ae47] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.518150738 0x72456b0ba] dbg_trace_log_ctrl: Get String Descriptor(Index = 7, Length = 510)
[ 1573.518239488 0x72456b763] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.518271415 0x72456b9c8] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.518476728 0x72456c92e] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.518545946 0x72456ce5f] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 ZsI ==> 0
[ 1573.518570217 0x72456d031] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.518640790 0x72456d57c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.518737561 0x72456dcbd] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.518815738 0x72456e29b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.518910686 0x72456e9b9] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.518941311 0x72456ec06] dbg_trace_log_ctrl: Get String Descriptor(Index = 6, Length = 4)
[ 1573.519025999 0x72456f260] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.519057144 0x72456f4b6] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.519151884 0x72456fbd0] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.519180999 0x72456fdff] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.519245530 0x7245702d7] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.519267769 0x724570482] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.519337092 0x7245709b5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.519429749 0x7245710a7] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.519510113 0x7245716af] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.519605478 0x724571dd6] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.519634905 0x72457200b] dbg_trace_log_ctrl: Get String Descriptor(Index = 8, Length = 510)
[ 1573.519721936 0x724572692] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.519752092 0x7245728d4] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.519846624 0x724572fec] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.519910478 0x7245734b5] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.519932926 0x724573664] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.520002353 0x724573b9a] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.520096051 0x7245742a1] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.520174176 0x72457487c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.520267874 0x724574f84] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.520299071 0x7245751db] dbg_trace_log_ctrl: Get String Descriptor(Index = 6, Length = 12)
[ 1573.520383446 0x72457582f] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.520415165 0x724575a90] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.520510790 0x7245761bc] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.520539436 0x7245763e2] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.520604071 0x7245768bb] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 12/12 zsI ==> 0
[ 1573.520626155 0x724576a62] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.520697144 0x724576fb6] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.520791051 0x7245776c0] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.520871259 0x724577cc5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.520963238 0x7245783ab] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.520993082 0x7245785e8] dbg_trace_log_ctrl: Get String Descriptor(Index = 9, Length = 510)
[ 1573.521075478 0x724578c16] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.521106259 0x724578e65] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.521198082 0x724579548] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.521263499 0x724579a30] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 28/28 ZsI ==> 0
[ 1573.521285738 0x724579bdb] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.521354176 0x72457a0fc] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.521442353 0x72457a799] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.521516207 0x72457ad23] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.521837405 0x72457c53b] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.521875061 0x72457c80e] dbg_trace_log_ctrl: Get String Descriptor(Index = 238, Length = 510)
[ 1573.521941519 0x72457cd09] dbg_send_ep_cmd: ep0out: cmd 'Set Stall' [404] params 00000000 00000000 00000000 --> status: Successful
[ 1573.522006051 0x72457d1e1] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.522034280 0x72457d3fe] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.526185217 0x724590b51] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.526223082 0x724590e28] dbg_trace_log_ctrl: Get String Descriptor(Index = 7, Length = 4)
[ 1573.526312405 0x7245914dc] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.526344801 0x724591749] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.526573863 0x724592878] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.526646415 0x724592de8] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.526672040 0x724592fd4] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.526740894 0x7245934fd] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.526835165 0x724593c10] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.526909957 0x7245941ab] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.527001155 0x724594883] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.527026051 0x724594a60] dbg_trace_log_ctrl: Get String Descriptor(Index = 7, Length = 18)
[ 1573.527100530 0x724594ff7] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.527206676 0x7245957ec] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.527277249 0x724595d37] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.527328551 0x724596111] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 zsI ==> 0
[ 1573.527350842 0x7245962bd] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.527402144 0x724596696] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.527470947 0x724596bbf] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.527523186 0x724596faa] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.531083290 0x7245a7aac] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.531112405 0x7245a7cdb] dbg_trace_log_ctrl: Get String Descriptor(Index = 8, Length = 4)
[ 1573.531182926 0x7245a8225] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.531212405 0x7245a845b] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.531284332 0x7245a89bf] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.531338863 0x7245a8dd7] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.531360842 0x7245a8f7c] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.531411936 0x7245a9352] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.531482717 0x7245a98a1] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.531536415 0x7245a9ca8] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.531607353 0x7245aa1fa] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.531632926 0x7245aa3e5] dbg_trace_log_ctrl: Get String Descriptor(Index = 8, Length = 20)
[ 1573.531697301 0x7245aa8b9] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.531725790 0x7245aaadc] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.531794801 0x7245ab009] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.531819697 0x7245ab1e6] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.531872197 0x7245ab5d7] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 zsI ==> 0
[ 1573.531894540 0x7245ab783] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.531941832 0x7245abb0f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.532010842 0x7245ac03d] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.532063238 0x7245ac42b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.534656363 0x7245b86a7] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.534689697 0x7245b8927] dbg_trace_log_ctrl: Get String Descriptor(Index = 9, Length = 4)
[ 1573.534777717 0x7245b8fc0] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.534808707 0x7245b9214] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.534898707 0x7245b98d4] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.534929801 0x7245b9b29] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.534994280 0x7245b9fff] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.535016311 0x7245ba1a6] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.535080686 0x7245ba679] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.535166676 0x7245baced] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.535238655 0x7245bb252] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.535323655 0x7245bb8b2] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.535352926 0x7245bbae5] dbg_trace_log_ctrl: Get String Descriptor(Index = 9, Length = 28)
[ 1573.535432874 0x7245bc0e4] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.535464853 0x7245bc349] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.535555374 0x7245bca14] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.535619124 0x7245bcedc] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 28/28 zsI ==> 0
[ 1573.535641832 0x7245bd090] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.535706103 0x7245bd562] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.535793655 0x7245bdbf3] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.535864124 0x7245be13c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.539001311 0x7245ccc86] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.539034072 0x7245ccefb] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 4)
[ 1573.539120165 0x7245cd56f] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.539151207 0x7245cd7c3] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.539243655 0x7245cdeb3] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.539272561 0x7245ce0de] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.539337926 0x7245ce5c5] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.539360374 0x7245ce774] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.539428238 0x7245cec8b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.539517353 0x7245cf33a] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.539592926 0x7245cf8e4] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.539682457 0x7245cff9c] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.539711676 0x7245d01cd] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 4)
[ 1573.539794644 0x7245d0805] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.539826415 0x7245d0a68] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.539917926 0x7245d1144] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.539980634 0x7245d15f9] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.540002717 0x7245d17a1] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.540071207 0x7245d1cc3] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.540160217 0x7245d2370] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.540233186 0x7245d28ea] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.540326259 0x7245d2fe5] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.540355894 0x7245d321e] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 48)
[ 1573.540439592 0x7245d3865] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.540469905 0x7245d3aaa] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.540559228 0x7245d415e] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.540622144 0x7245d4616] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 48/48 zsI ==> 0
[ 1573.540644072 0x7245d47ba] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.540710686 0x7245d4cba] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.540798290 0x7245d534c] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.540872092 0x7245d58d5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.540959176 0x7245d5f5d] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.540987926 0x7245d6184] dbg_trace_log_ctrl: Get String Descriptor(Index = 2, Length = 48)
[ 1573.541071103 0x7245d67c1] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.541102457 0x7245d6a1c] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.541194332 0x7245d7100] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.541257665 0x7245d75c0] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 48/48 zsI ==> 0
[ 1573.541279644 0x7245d7765] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.541346884 0x7245d7c71] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.541436624 0x7245d832b] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.541508551 0x7245d8890] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.541595009 0x7245d8f0d] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.541623707 0x7245d9134] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 4)
[ 1573.541709072 0x7245d979a] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.541740842 0x7245d99fd] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.541833030 0x7245da0e7] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.541896519 0x7245da5a9] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.541918655 0x7245da753] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.541986832 0x7245dac70] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.542075217 0x7245db310] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.542148551 0x7245db890] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.542366572 0x7245dc8ea] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.542396988 0x7245dcb33] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 4)
[ 1573.542479749 0x7245dd168] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.542511259 0x7245dd3c5] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.542601103 0x7245dda82] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.542665999 0x7245ddf5f] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.542689280 0x7245de11f] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.542753238 0x7245de5ea] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.542852822 0x7245ded63] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.542928967 0x7245df319] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.543021259 0x7245dfa05] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.543050999 0x7245dfc3f] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 18)
[ 1573.543138290 0x7245e02cb] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.543169697 0x7245e0526] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.543262144 0x7245e0c16] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.543326988 0x7245e10f2] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 zsI ==> 0
[ 1573.543349280 0x7245e129f] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.543416311 0x7245e17a5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.543506467 0x7245e1e68] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.543580530 0x7245e23f7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.543672249 0x7245e2ad8] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.543701572 0x7245e2d0a] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 18)
[ 1573.543786936 0x7245e3372] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.543818863 0x7245e35d6] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.543911832 0x7245e3cd0] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.543976311 0x7245e41a6] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 zsI ==> 0
[ 1573.543998707 0x7245e4353] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.544068342 0x7245e488d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.544159801 0x7245e4f69] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.544235634 0x7245e5519] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.544326832 0x7245e5bf0] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.544357249 0x7245e5e38] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep1in)
[ 1573.544421103 0x7245e6302] dbg_send_ep_cmd: ep1in: cmd 'End Transfer' [30d08] params 00000000 00000000 00000000 --> status: Successful
[ 1573.544443811 0x7245e64b5] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.544535374 0x7245e6b93] event (080301c6): ep1in: Endpoint Command Complete
[ 1573.544598342 0x7245e704c] dbg_send_ep_cmd: ep1in: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.544662665 0x7245e751f] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.544751572 0x7245e7bcb] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.544825426 0x7245e8155] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.545031467 0x7245e90c9] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.545062249 0x7245e9317] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep2in)
[ 1573.545121884 0x7245e9790] dbg_send_ep_cmd: ep2in: cmd 'End Transfer' [50d08] params 00000000 00000000 00000000 --> status: Successful
[ 1573.545144280 0x7245e993f] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.545239853 0x7245ea06a] event (080501ca): ep2in: Endpoint Command Complete
[ 1573.545300009 0x7245ea4ed] dbg_send_ep_cmd: ep2in: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.545363603 0x7245ea9b2] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.545453551 0x7245eb071] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.545527769 0x7245eb602] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.545724749 0x7245ec4c8] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.545756363 0x7245ec726] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep1out)
[ 1573.545816624 0x7245ecbac] dbg_send_ep_cmd: ep1out: cmd 'End Transfer' [20d08] params 00000000 00000000 00000000 --> status: Successful
[ 1573.545838915 0x7245ecd58] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.545931832 0x7245ed450] event (080201c4): ep1out: Endpoint Command Complete
[ 1573.545994228 0x7245ed8fe] dbg_send_ep_cmd: ep1out: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.546055999 0x7245edd9f] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.546119801 0x7245ee269] dbg_send_ep_cmd: ep1out: cmd 'Start Transfer' [406] params 00000000 efff8000 00000000 --> status: Successful
[ 1573.546278342 0x7245eee4c] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.546354801 0x7245ef409] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.546447822 0x7245efb03] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.546479384 0x7245efd61] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep2out)
[ 1573.546538863 0x7245f01d7] dbg_send_ep_cmd: ep2out: cmd 'End Transfer' [40d08] params 00000000 00000000 00000000 --> status: Successful
[ 1573.546561572 0x7245f038a] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.546656884 0x7245f0ab1] event (080401c8): ep2out: Endpoint Command Complete
[ 1573.546716780 0x7245f0f2e] dbg_send_ep_cmd: ep2out: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.546778447 0x7245f13cf] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.546850322 0x7245f1933] dbg_send_ep_cmd: ep2out: cmd 'Start Transfer' [406] params 00000000 efff6000 00000000 --> status: Successful
[ 1573.546940686 0x7245f1ff9] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.547018759 0x7245f25d4] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.553876415 0x724612828] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.553910217 0x724612ab1] dbg_trace_log_ctrl: Get String Descriptor(Index = 6, Length = 4)
[ 1573.554000322 0x724613173] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.554034905 0x72461340b] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.554131728 0x724613b4e] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.554200947 0x72461407f] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.554224697 0x724614247] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.554294384 0x724614781] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.554496936 0x7246156b2] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.554578551 0x724615cd0] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.554672353 0x7246163da] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.554703967 0x724616639] dbg_trace_log_ctrl: Get String Descriptor(Index = 6, Length = 12)
[ 1573.554789697 0x724616ca7] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.554821624 0x724616f0c] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.554916415 0x724617628] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.554982145 0x724617b15] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 12/12 zsI ==> 0
[ 1573.555005165 0x724617cd0] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.555075217 0x724618211] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.555166572 0x7246188ea] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.555243551 0x724618eb1] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.555449436 0x724619e22] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.555481103 0x72461a082] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 4)
[ 1573.555567509 0x72461a6fd] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.555599384 0x72461a961] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.555695999 0x72461b09f] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.555759540 0x72461b564] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 4/4 zsI ==> 0
[ 1573.555782457 0x72461b71b] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.555854280 0x72461bc7f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.555949957 0x72461c3ac] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.556030947 0x72461c9bf] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.556123707 0x72461d0b4] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.556153863 0x72461d2f7] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 18)
[ 1573.556237249 0x72461d938] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.556269228 0x72461db9e] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.556364540 0x72461e2c3] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.556429853 0x72461e7aa] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 zsI ==> 0
[ 1573.556452926 0x72461e964] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.556521780 0x72461ee8f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.556615009 0x72461f58d] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.556691936 0x72461fb52] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.557498499 0x7246237d0] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.557529697 0x724623a26] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep5in)
[ 1573.557590217 0x724623eb1] dbg_send_ep_cmd: ep5in: cmd 'End Transfer' [b0d08] params 00000000 00000000 00000000 --> status: Successful
[ 1573.557613030 0x724624067] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.557710322 0x7246247b2] event (080b01d6): ep5in: Endpoint Command Complete
[ 1573.557771988 0x724624c53] dbg_send_ep_cmd: ep5in: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.557833655 0x7246250f3] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.557925634 0x7246257d9] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.558001884 0x724625d90] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.558306051 0x724627461] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.558341884 0x724627711] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep4in)
[ 1573.558402353 0x724627b9a] dbg_send_ep_cmd: ep4in: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.558425322 0x724627d53] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.558493186 0x72462826a] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.558584488 0x724628943] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.558659540 0x724628ee4] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.558855530 0x724629d97] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.558886988 0x724629ff3] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep3out)
[ 1573.558947717 0x72462a480] dbg_send_ep_cmd: ep3out: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.558970217 0x72462a631] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.559043655 0x72462abb2] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.559137561 0x72462b2be] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.559212301 0x72462b859] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.559756467 0x72462e128] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.559787249 0x72462e377] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep4in)
[ 1573.559848707 0x72462e813] dbg_send_ep_cmd: ep4in: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.559870842 0x72462e9bd] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.559941676 0x72462ef0d] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.560036103 0x72462f621] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.560111415 0x72462fbc7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.560397665 0x724631140] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.560430686 0x7246313ba] dbg_trace_log_ctrl: Clear Endpoint Feature(Halt ep3out)
[ 1573.560490478 0x724631836] dbg_send_ep_cmd: ep3out: cmd 'Clear Stall' [405] params 00000000 00000000 00000000 --> status: Successful
[ 1573.560512822 0x7246319e3] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.560581155 0x724631f03] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.560670790 0x7246325bb] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.560747405 0x724632b7b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.561184176 0x724634c3d] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.561215738 0x724634e9b] dbg_trace_log_ctrl: 21 22 00 00 02 00 00 00
[ 1573.561359020 0x72463595a] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.561429697 0x724635ea7] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.561521311 0x724636585] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.561552978 0x7246367e6] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 0/0 zsI ==> 0
[ 1573.561615322 0x724636c93] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.561704697 0x724637347] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.561734645 0x724637585] dbg_trace_log_ctrl: 21 22 01 00 02 00 00 00
[ 1573.561789801 0x7246379a8] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.561859228 0x724637ede] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.561948186 0x724638589] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.561980217 0x7246387f0] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 0/0 zsI ==> 0
[ 1573.562044488 0x724638cc2] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.563995686 0x724641f1a] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.564027822 0x724642182] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.564131520 0x724642949] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.564164592 0x724642bc4] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.564260895 0x7246432fd] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.564331728 0x72464384e] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.564406988 0x724643df3] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.564478342 0x72464434c] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.564569957 0x724644a2c] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.564644280 0x724644fbf] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.566590582 0x72464e1b7] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.566657197 0x72464e6b7] dbg_prepare: ep5in: trb ffffffc05a97d000 (E1:D0) buf 00000000ee77c600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.566840947 0x72464f47f] dbg_send_ep_cmd: ep5in: cmd 'Start Transfer' [406] params 00000000 ed5ff000 00000000 --> status: Successful
[ 1573.570873603 0x7246622f2] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.570906415 0x724662568] dbg_complete: ep5in: trb ffffffc05a97d000 (E1:D1) buf 00000000ee77c600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.570987457 0x724662b7b] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.571081832 0x724663290] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.571114488 0x724663503] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.571235686 0x724663e1a] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.571267457 0x72466407c] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.571362092 0x724664794] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.571441103 0x724664d82] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 188/188 ZsI ==> 0
[ 1573.571472145 0x724664fd6] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.571539749 0x7246654e7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.571628551 0x724665b90] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.571703186 0x724666129] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.571797092 0x724666835] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.571827978 0x724666a85] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 12)
[ 1573.571938186 0x7246672ca] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.571969280 0x72466751f] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.572062457 0x724667c1b] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.572145895 0x72466825e] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 12/12 zsI ==> 0
[ 1573.572221988 0x724668812] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.572291363 0x724668d47] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.572380478 0x7246693f6] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.572454436 0x724669981] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.573587770 0x72466ee82] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.573623915 0x72466f138] dbg_prepare: ep5in: trb ffffffc05a97d010 (E2:D1) buf 00000000ed773600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.573678863 0x72466f557] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.574859749 0x724674de8] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.574893186 0x72467506a] dbg_complete: ep5in: trb ffffffc05a97d010 (E2:D2) buf 00000000ed773600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.574950374 0x7246754b3] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.575040113 0x724675b6f] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.575070009 0x724675dad] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.575177613 0x7246765be] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.575210426 0x724676834] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.575306832 0x724676f70] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.575336988 0x7246771b3] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.575402665 0x7246776a0] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 19/19 ZsI ==> 0
[ 1573.575434905 0x72467790b] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.575504697 0x724677e47] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.575595947 0x724678520] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.575671884 0x724678ad0] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.575764384 0x7246791c1] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.575794801 0x724679409] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.575894488 0x724679b83] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.575926415 0x724679de8] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.576019957 0x72467a4ec] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.576089228 0x72467aa1e] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.576169853 0x72467b02a] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.576241832 0x72467b590] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.576333707 0x72467bc74] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.576408342 0x72467c20c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.577302613 0x72468051f] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.577351207 0x7246808c4] dbg_prepare: ep5in: trb ffffffc05a97d020 (E3:D2) buf 00000000edae7600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.577404540 0x724680cc4] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.578855165 0x724687990] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.578887665 0x724687c00] dbg_complete: ep5in: trb ffffffc05a97d020 (E3:D3) buf 00000000edae7600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.578963082 0x7246881a8] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.579055009 0x72468888c] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.579085582 0x724688ad8] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.579207874 0x724689404] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.579242249 0x724689698] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.579337926 0x724689dc5] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.579419697 0x72468a3e7] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.579450165 0x72468a630] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.579520686 0x72468ab7a] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.579609332 0x72468b220] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.579682197 0x72468b796] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.579770374 0x72468be33] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.579798967 0x72468c059] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 77)
[ 1573.579906884 0x72468c871] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.579938447 0x72468cace] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.580032457 0x72468d1dc] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.580117301 0x72468d838] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 77/77 zsI ==> 0
[ 1573.580218395 0x72468dfce] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.580290061 0x72468e52d] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.580383915 0x72468ec38] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.580459072 0x72468f1db] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.581550009 0x7246943ac] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.581605009 0x7246947cc] dbg_prepare: ep5in: trb ffffffc05a97d030 (E4:D3) buf 00000000edbfd600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.581660686 0x724694bf9] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.582858343 0x72469a5ce] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.582889905 0x72469a82b] dbg_complete: ep5in: trb ffffffc05a97d030 (E4:D4) buf 00000000edbfd600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.582962926 0x72469ada5] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.583054853 0x72469b489] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.583084020 0x72469b6bb] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.583207197 0x72469bff7] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.583239384 0x72469c260] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.583335322 0x72469c993] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.583415582 0x72469cf98] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 91/91 ZsI ==> 0
[ 1573.583445322 0x72469d1d2] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.583514540 0x72469d704] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.583603811 0x72469ddb6] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.583676728 0x72469e32e] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.583764124 0x72469e9bc] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.583793290 0x72469ebeb] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 17)
[ 1573.583901051 0x72469f400] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.583931468 0x72469f648] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.584024384 0x72469fd40] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.584053603 0x72469ff72] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.584134228 0x7246a057e] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 17/17 zsI ==> 0
[ 1573.584209593 0x7246a0b24] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.584280738 0x7246a107b] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.584371936 0x7246a1752] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.584450165 0x7246a1d30] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.585482040 0x7246a6a93] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.585530270 0x7246a6e31] dbg_prepare: ep5in: trb ffffffc05a97d040 (E5:D4) buf 00000000edaea600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.585586363 0x7246a7267] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.586855478 0x7246ad196] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.586886363 0x7246ad3e7] dbg_complete: ep5in: trb ffffffc05a97d040 (E5:D5) buf 00000000edaea600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.586957145 0x7246ad936] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.587047770 0x7246ae002] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.587078811 0x7246ae255] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.587195790 0x7246aeb1b] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.587228030 0x7246aed87] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.587321676 0x7246af48d] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.587400270 0x7246afa71] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 28/28 ZsI ==> 0
[ 1573.587430582 0x7246afcb8] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.587499072 0x7246b01db] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.587587197 0x7246b0876] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.587661051 0x7246b0e01] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.587750999 0x7246b14c0] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.587781520 0x7246b1709] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 17)
[ 1573.587891832 0x7246b1f50] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.587923655 0x7246b21b2] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.588018343 0x7246b28cd] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.588101676 0x7246b2f0d] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 17/17 zsI ==> 0
[ 1573.588176311 0x7246b34a6] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.588248343 0x7246b3a0d] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.588341311 0x7246b4105] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.588418238 0x7246b46ca] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.589392926 0x7246b8fe5] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.589439436 0x7246b9362] dbg_prepare: ep5in: trb ffffffc05a97d050 (E6:D5) buf 00000000edaeb600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.589494957 0x7246b978c] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.590853186 0x7246bfd6a] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.590886051 0x7246bffe1] dbg_complete: ep5in: trb ffffffc05a97d050 (E6:D6) buf 00000000edaeb600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.590956051 0x7246c0520] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.591045270 0x7246c0bd2] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.591074957 0x7246c0e0b] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.591190634 0x7246c16b9] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.591223030 0x7246c1926] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.591317145 0x7246c2035] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.591396103 0x7246c2622] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.591425843 0x7246c285c] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.591493551 0x7246c2d70] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.591584853 0x7246c3449] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.591663343 0x7246c3a2d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.591755009 0x7246c410c] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.591784176 0x7246c433d] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.591892249 0x7246c4b57] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.591924957 0x7246c4dcb] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.592017613 0x7246c54bf] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.592099072 0x7246c5adb] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.592173915 0x7246c6078] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.592241988 0x7246c6593] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.592331572 0x7246c6c4b] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.592408603 0x7246c7212] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.594116051 0x7246cf221] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.594149488 0x7246cf4a3] dbg_prepare: ep5in: trb ffffffc05a97d060 (E7:D6) buf 00000000ee27f600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.594204540 0x7246cf8c3] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.594853968 0x7246d2978] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.594884540 0x7246d2bc3] dbg_complete: ep5in: trb ffffffc05a97d060 (E7:D7) buf 00000000ee27f600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.594939645 0x7246d2fe5] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.595028915 0x7246d3697] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.595058134 0x7246d38c9] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.595162718 0x7246d40a0] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.595194905 0x7246d430b] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.595285530 0x7246d49d7] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.595349697 0x7246d4ea6] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.595379540 0x7246d50e3] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.595452353 0x7246d565a] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.595542040 0x7246d5d13] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.595617301 0x7246d62b9] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.595708603 0x7246d6991] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.595737561 0x7246d6bbe] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.595834280 0x7246d72ff] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.595865426 0x7246d7555] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.595958290 0x7246d7c4c] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.596025790 0x7246d815c] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.596098499 0x7246d86d0] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.596171207 0x7246d8c43] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.596264801 0x7246d9348] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.596340530 0x7246d98f7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.597374645 0x7246de686] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.597406884 0x7246de8f1] dbg_prepare: ep5in: trb ffffffc05a97d070 (E8:D7) buf 00000000ee34d600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.597460322 0x7246decf2] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.598957405 0x7246e5d3a] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.598988030 0x7246e5f87] dbg_complete: ep5in: trb ffffffc05a97d070 (E8:D8) buf 00000000ee34d600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.599046155 0x7246e63e3] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.599135947 0x7246e6a9f] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.599165999 0x7246e6ce0] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.599270582 0x7246e74b8] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.599302561 0x7246e771e] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.599395582 0x7246e7e17] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.599462145 0x7246e8316] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.599493186 0x7246e856a] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.599562613 0x7246e8a9f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.599653499 0x7246e916f] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.599730218 0x7246e9730] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.599825686 0x7246e9e5a] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.599856832 0x7246ea0b0] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.599960478 0x7246ea876] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.599991572 0x7246eaacb] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.600090947 0x7246eb23f] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.600122926 0x7246eb4a5] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.600195686 0x7246eba1a] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.600272665 0x7246ebfe0] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.600345478 0x7246ec556] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.600444280 0x7246eccbf] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.600524801 0x7246ed2c9] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.601538811 0x7246f1ed6] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.601571520 0x7246f2149] dbg_prepare: ep5in: trb ffffffc05a97d080 (E9:D8) buf 00000000ee348600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.601629488 0x7246f25a3] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.602961051 0x7246f8982] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.602998707 0x7246f8c54] dbg_complete: ep5in: trb ffffffc05a97d080 (E9:D9) buf 00000000ee348600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.603066520 0x7246f916a] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.603099697 0x7246f93e7] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.603134801 0x7246f968a] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.603260426 0x7246f9ff5] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.603300634 0x7246fa2f9] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.603411051 0x7246fab41] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.603488759 0x7246fb115] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.603527613 0x7246fb3ff] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.603605790 0x7246fb9dc] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.603711572 0x7246fc1cb] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.603798447 0x7246fc84f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.603903811 0x7246fd036] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.603938447 0x7246fd2cf] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.604054540 0x7246fdb84] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.604093655 0x7246fde73] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.604201624 0x7246fe68c] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.604281624 0x7246fec8c] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.604377561 0x7246ff3be] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.604458707 0x7246ff9d4] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.604568603 0x724700212] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.604657197 0x7247008b7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.605983447 0x724706c2f] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.606023915 0x724706f38] dbg_prepare: ep5in: trb ffffffc05a97d090 (E10:D9) buf 00000000efafb600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.606089540 0x724707425] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.606918447 0x72470b24f] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.606958290 0x72470b54c] dbg_complete: ep5in: trb ffffffc05a97d090 (E10:D10) buf 00000000efafb600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.607029905 0x72470baab] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.607063447 0x72470bd2f] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.607102145 0x72470c017] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.607230895 0x72470c9be] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.607270999 0x72470ccc0] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.607381728 0x72470d50e] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.607459749 0x72470dae8] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.607499332 0x72470dde0] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.607578134 0x72470e3c9] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.607686572 0x72470ebeb] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.607775374 0x72470f294] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.607887874 0x72470fb05] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.607926363 0x72470fde7] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.608043030 0x7247106a7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.608082978 0x7247109a6] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.608190270 0x7247111b2] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.608274228 0x7247117fe] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.608501311 0x724712906] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.608584176 0x724712f3e] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.608829228 0x72471419e] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.608917926 0x724714845] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.610286780 0x72471aeee] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.610311155 0x72471b0c2] dbg_prepare: ep5in: trb ffffffc05a97d0a0 (E11:D10) buf 00000000ed079600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.610342926 0x72471b324] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.610899645 0x72471dce6] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.610944228 0x72471e03e] dbg_complete: ep5in: trb ffffffc05a97d0a0 (E11:D11) buf 00000000ed079600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.611019697 0x72471e5e8] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.611054645 0x72471e887] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.611092457 0x72471eb5c] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.611230113 0x72471f5af] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.611273707 0x72471f8f4] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.611386416 0x724720168] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.611424020 0x72472043a] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.611502561 0x724720a1e] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.611543916 0x724720d38] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.611627249 0x724721379] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.611736780 0x724721bb0] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.611825218 0x724722251] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.611935738 0x724722a9c] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.611973186 0x724722d6a] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.612092822 0x724723663] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.612133863 0x724723977] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.612245113 0x7247241cf] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.612329697 0x724724828] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.612444488 0x7247250c3] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.612527978 0x724725706] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.612640166 0x724725f70] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.612730738 0x72472663b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.613406363 0x7247298e6] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.613422093 0x724729a15] dbg_prepare: ep5in: trb ffffffc05a97d0b0 (E12:D11) buf 00000000ed07a600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.613454384 0x724729c80] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.614918655 0x724730a53] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.614958968 0x724730d59] dbg_complete: ep5in: trb ffffffc05a97d0b0 (E12:D12) buf 00000000ed07a600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.615031363 0x7247312c7] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.615145113 0x724731b4f] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.615183343 0x724731e2d] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.615319072 0x72473285b] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.615361103 0x724732b82] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.615477041 0x724733434] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.615560999 0x724733a80] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 44/44 ZsI ==> 0
[ 1573.615609488 0x724733e23] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.615693030 0x724734467] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.615808395 0x724734d0e] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.615898863 0x7247353d7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.616011416 0x724735c48] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.616050270 0x724735f32] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.616179801 0x7247368e9] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.616222353 0x724736c1a] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.616337874 0x7247374c4] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.616427978 0x724737b86] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.616544124 0x72473843c] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.616626624 0x724738a6c] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.616737041 0x7247392b4] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.616826780 0x72473996f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.617315530 0x72473be16] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.617331988 0x72473bf52] dbg_prepare: ep5in: trb ffffffc05a97d0c0 (E13:D12) buf 00000000ed07b600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.617363395 0x72473c1ad] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.618964853 0x7247439cb] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.619011207 0x724743d45] dbg_complete: ep5in: trb ffffffc05a97d0c0 (E13:D13) buf 00000000ed07b600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.619095009 0x72474438e] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.619136936 0x7247446b2] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.619179853 0x7247449eb] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.619332874 0x724745565] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.619382197 0x724745917] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.619506988 0x724746274] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.619548447 0x72474658f] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.619635061 0x724746c0e] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 23/23 ZsI ==> 0
[ 1573.619682093 0x724746f95] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.619767093 0x7247475f5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.619885478 0x724747ed6] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.619980530 0x7247485f8] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.620097718 0x724748ec2] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.620139072 0x7247491db] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.620274332 0x724749c01] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.620320166 0x724749f70] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.620437770 0x72474a843] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.620530843 0x72474af3d] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.620659749 0x72474b8e9] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.620747874 0x72474bf85] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.620866936 0x72474c873] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.620960738 0x72474cf7c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.621910999 0x7247516bf] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.621931468 0x724751849] dbg_prepare: ep5in: trb ffffffc05a97d0d0 (E14:D13) buf 00000000ed07f600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.621967405 0x724751afb] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.622928134 0x724756309] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.622970218 0x724756631] dbg_complete: ep5in: trb ffffffc05a97d0d0 (E14:D14) buf 00000000ed07f600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.623046259 0x724756be6] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.623163863 0x7247574b7] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.623206728 0x7247577ee] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.623347509 0x72475827d] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.623393551 0x7247585f1] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.623513968 0x724758ef9] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.623598134 0x724759549] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.623642978 0x7247598a6] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.623729957 0x724759f2c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.623843759 0x72475a7b5] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.623937770 0x72475aec2] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.624210843 0x72475c33d] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.624254384 0x72475c681] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.624384593 0x72475d046] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.624430218 0x72475d3b1] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.624549280 0x72475dc9f] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.624588030 0x72475df87] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.624676468 0x72475e629] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.624798968 0x72475ef5a] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.624884957 0x72475f5cd] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.625006624 0x72475feed] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.625101676 0x72476060d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.626186728 0x72476576e] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.626224593 0x724765a45] dbg_prepare: ep5in: trb ffffffc05a97d0e0 (E15:D14) buf 00000000ee373600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.626279645 0x724765e66] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.626857093 0x7247689b5] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.626888395 0x724768c0e] dbg_complete: ep5in: trb ffffffc05a97d0e0 (E15:D15) buf 00000000ee373600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.626945426 0x724769055] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.627034749 0x724769707] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.627063916 0x724769938] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.627171728 0x72476a14e] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.627202718 0x72476a3a1] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.627294645 0x72476aa86] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.627323499 0x72476acaf] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.627389280 0x72476b19f] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 87/87 ZsI ==> 0
[ 1573.627419020 0x72476b3da] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.627487301 0x72476b8f8] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.627576520 0x72476bfaa] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.627650166 0x72476c530] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.627904020 0x72476d839] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.627934801 0x72476da89] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.628034124 0x72476e1fc] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.628065738 0x72476e45b] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.628159176 0x72476eb5c] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.628229853 0x72476f0a9] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.628303707 0x72476f634] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.628374697 0x72476fb86] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.628467874 0x724770284] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.628544020 0x724770839] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.630142405 0x72477801b] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.630200426 0x724778474] dbg_prepare: ep5in: trb ffffffc05a97d0f0 (E16:D15) buf 00000000edd4d600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.630254905 0x72477888b] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.630906416 0x72477b968] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.630937926 0x72477bbc5] dbg_complete: ep5in: trb ffffffc05a97d0f0 (E16:D16) buf 00000000edd4d600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.631015530 0x72477c196] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.631105530 0x72477c856] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.631135218 0x72477ca90] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.631255791 0x72477d39c] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.631288499 0x72477d610] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.631383447 0x72477dd2f] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.631412249 0x72477df58] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.631494072 0x72477e57a] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 28/28 ZsI ==> 0
[ 1573.631524905 0x72477e7ca] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.631592718 0x72477ece1] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.631684801 0x72477f3c9] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.631761103 0x72477f982] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.631959176 0x72478085d] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.631990374 0x724780ab3] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.632105113 0x72478134f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.632137926 0x7247815c5] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.632233343 0x724781ced] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.632318447 0x72478234f] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.632418759 0x724782ad5] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.632491207 0x724783044] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.632584853 0x72478374a] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.632660738 0x724783cfa] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.634388811 0x72478be96] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.634434853 0x72478c209] dbg_prepare: ep5in: trb ffffffc05a97d100 (E17:D16) buf 00000000edd4d600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.634489436 0x72478c622] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.635027926 0x72478ee85] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.635061259 0x72478f105] dbg_complete: ep5in: trb ffffffc05a97d100 (E17:D17) buf 00000000edd4d600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.635135374 0x72478f694] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.635227926 0x72478fd85] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.635258239 0x72478ffcb] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.635382353 0x72479091a] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.635416051 0x724790ba1] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.635512509 0x7247912dd] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.635596416 0x724791928] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.635627874 0x724791b84] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.635695947 0x72479209f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.635789593 0x7247927a5] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.635867093 0x724792d75] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.636086103 0x724793de2] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.636119749 0x724794068] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.636239176 0x72479495d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.636272509 0x724794bdd] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.636369124 0x72479531c] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.636459384 0x7247959e1] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.636559645 0x724796166] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.636633499 0x7247966f0] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.636730270 0x724796e32] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.636809436 0x724797422] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.646933447 0x7247c6b6f] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.647010426 0x7247c7134] dbg_prepare: ep5in: trb ffffffc05a97d110 (E18:D17) buf 00000000edf87600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.647058811 0x7247c74d6] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.650856676 0x7247d91ae] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.650894645 0x7247d9486] dbg_complete: ep5in: trb ffffffc05a97d110 (E18:D18) buf 00000000edf87600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.650990166 0x7247d9bb0] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.651070947 0x7247da1bf] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.651098864 0x7247da3d7] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.651229332 0x7247dad9f] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.651262614 0x7247db01f] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.651335114 0x7247db58f] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.651401468 0x7247dba88] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.651432718 0x7247dbce0] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.651484905 0x7247dc0ca] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.651556624 0x7247dc62b] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.651612614 0x7247dca5f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.651688707 0x7247dd013] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.651713864 0x7247dd1f7] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 35)
[ 1573.651803811 0x7247dd8b5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.651833186 0x7247ddaea] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.651904697 0x7247de047] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.651928968 0x7247de218] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.651996936 0x7247de732] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 35/35 zsI ==> 0
[ 1573.652103655 0x7247def33] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.652155999 0x7247df320] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.652329072 0x7247e001b] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.652385895 0x7247e045d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.653663447 0x7247e642f] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.653702509 0x7247e671c] dbg_prepare: ep5in: trb ffffffc05a97d120 (E19:D18) buf 00000000ed353600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.653745999 0x7247e6a5f] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.654839853 0x7247ebc6a] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.654868343 0x7247ebe8c] dbg_complete: ep5in: trb ffffffc05a97d120 (E19:D19) buf 00000000ed353600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.654920791 0x7247ec27b] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.654994436 0x7247ec801] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.655020061 0x7247ec9ed] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.655113968 0x7247ed0f9] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.655144645 0x7247ed345] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.655219072 0x7247ed8db] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.655272509 0x7247edcdd] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.655303343 0x7247edf2d] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.655354905 0x7247ee30a] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.655428186 0x7247ee88a] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.655484541 0x7247eecc4] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.655742874 0x7247f0024] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.655769280 0x7247f021f] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 17)
[ 1573.655849697 0x7247f0827] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.655878968 0x7247f0a59] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.655953447 0x7247f0fef] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.656009697 0x7247f1427] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 17/17 zsI ==> 0
[ 1573.656109020 0x7247f1b9a] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.656161728 0x7247f1f8e] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.656235895 0x7247f251e] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.656291676 0x7247f294d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.656364384 0x7247f2ec1] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.656389020 0x7247f309a] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 17)
[ 1573.656467978 0x7247f3686] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.656496520 0x7247f38aa] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.656570009 0x7247f3e2c] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.656625582 0x7247f4258] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 17/17 zsI ==> 0
[ 1573.656658030 0x7247f44c6] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.656709280 0x7247f489e] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.656781207 0x7247f4e04] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.656838447 0x7247f524e] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.656913030 0x7247f57e7] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.656936780 0x7247f59ae] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 16)
[ 1573.657014905 0x7247f5f8b] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.657043499 0x7247f61b0] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.657114749 0x7247f6708] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.657169593 0x7247f6b25] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 16/16 zsI ==> 0
[ 1573.657202718 0x7247f6da0] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.657252457 0x7247f715c] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.657324593 0x7247f76c5] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.657380478 0x7247f7af5] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.658669905 0x7247fdbab] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.658703499 0x7247fde30] dbg_prepare: ep5in: trb ffffffc05a97d130 (E20:D19) buf 00000000ed353600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.658747666 0x7247fe17f] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.662849853 0x72481152a] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.662880062 0x72481176d] dbg_complete: ep5in: trb ffffffc05a97d130 (E20:D20) buf 00000000ed353600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.662939072 0x724811bdb] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.663013655 0x724812173] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.663040114 0x72481236f] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.663135687 0x724812a9a] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.663166207 0x724812ce4] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.663236624 0x72481322c] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.663287718 0x724813600] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.663342978 0x724813a25] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.663371416 0x724813c47] dbg_prepare: ep5in: trb ffffffc05a97d140 (E21:D20) buf 00000000ed353600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.663412978 0x724813f66] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.663442197 0x724814197] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.663490582 0x724814538] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.663560530 0x724814a76] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.663614124 0x724814e7c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.666839905 0x72482406b] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.666867770 0x724824281] dbg_complete: ep5in: trb ffffffc05a97d140 (E21:D21) buf 00000000ed353600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.666917457 0x72482463b] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.667021520 0x724824e0a] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.667047197 0x724824ff7] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.667140062 0x7248256ee] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.667169541 0x724825923] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.667240374 0x724825e74] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.667294541 0x724826284] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.667344332 0x724826640] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.667371103 0x724826842] dbg_prepare: ep5in: trb ffffffc05a97d150 (E22:D21) buf 00000000ed353600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.667412301 0x724826b59] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.667442405 0x724826d9a] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.667493759 0x724827174] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.667567093 0x7248276f4] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.667623030 0x724827b26] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.670878134 0x724836f49] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.670912666 0x7248371e0] dbg_complete: ep5in: trb ffffffc05a97d150 (E22:D22) buf 00000000ed353600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.670972301 0x724837659] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.671061364 0x724837d07] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.671091364 0x724837f46] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.671200687 0x72483877a] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.671231989 0x7248389d3] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.671317614 0x72483903f] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.671380166 0x7248394f0] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 24/24 ZsI ==> 0
[ 1573.671410478 0x724839736] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.671477197 0x724839c37] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.671558916 0x72483a257] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.671630895 0x72483a7be] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.671714072 0x72483adfb] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.671743499 0x72483b02f] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 35)
[ 1573.671834853 0x72483b70a] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.671864801 0x72483b948] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.671948343 0x72483bf8c] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.672015166 0x72483c490] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 35/35 zsI ==> 0
[ 1573.672096520 0x72483caaa] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.672163239 0x72483cfaa] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.672246364 0x72483d5e7] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.672314593 0x72483db04] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.673545582 0x724843758] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.673589228 0x724843a9e] dbg_prepare: ep5in: trb ffffffc05a97d160 (E23:D22) buf 00000000ee20f600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.673641103 0x724843e82] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.674858759 0x7248499d4] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.674892301 0x724849c59] dbg_complete: ep5in: trb ffffffc05a97d160 (E23:D23) buf 00000000ee20f600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.674947353 0x72484a07a] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.675031676 0x72484a6cd] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.675061572 0x72484a90a] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.675165062 0x72484b0ce] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.675196259 0x72484b324] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.675284124 0x72484b9bc] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.675348968 0x72484be99] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.675378916 0x72484c0d8] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.675440999 0x72484c57f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.675524437 0x72484cbc2] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.675594020 0x72484d0fa] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.675678759 0x72484d755] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.675709072 0x72484d99b] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 17)
[ 1573.675803082 0x72484e0a7] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.675833864 0x72484e2f7] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.675921207 0x72484e983] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.675952562 0x72484ebde] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.676019020 0x72484f0da] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 17/17 zsI ==> 0
[ 1573.676122926 0x72484f8a4] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.676189697 0x72484fda7] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.676272718 0x7248503e1] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.676341520 0x72485090a] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.676423447 0x724850f2e] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.676452614 0x72485115f] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 17)
[ 1573.676545114 0x72485184f] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.676576259 0x724851aa4] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.676663187 0x724852129] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.676692562 0x72485235e] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.676759384 0x724852861] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 17/17 zsI ==> 0
[ 1573.676793707 0x724852af4] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.676856572 0x724852faa] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.676939437 0x7248535e2] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.677008239 0x724853b0a] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.677091364 0x724854147] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.677120687 0x724854379] dbg_trace_log_ctrl: Get Device Status(Length = 2)
[ 1573.677195322 0x724854913] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.677222301 0x724854b19] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.677310791 0x7248551bb] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.677373864 0x724855676] dbg_gadget_giveback: ep0out: req ffffff87cd156918 length 2/2 zsI ==> 0
[ 1573.677397666 0x724855840] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.677462926 0x724855d25] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.677544645 0x724856346] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.677614541 0x724856884] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.677697197 0x724856eb7] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.677727145 0x7248570f6] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 33)
[ 1573.677823759 0x724857835] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.677854437 0x724857a82] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.677940218 0x7248580f1] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.678001572 0x72485858b] dbg_prepare: ep5in: trb ffffffc05a97d170 (E24:D23) buf 00000000edbb6600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.678053447 0x72485896f] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.678080687 0x724858b7b] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.678151312 0x7248590c6] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 33/33 zsI ==> 0
[ 1573.678189541 0x7248593a4] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.678259541 0x7248598e4] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.678466676 0x72485a86c] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.678538447 0x72485adcf] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.678622614 0x72485b41e] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.678653499 0x72485b670] dbg_trace_log_ctrl: Get String Descriptor(Index = 7, Length = 258)
[ 1573.678738655 0x72485bcd3] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.678769645 0x72485bf25] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.678856155 0x72485c5a3] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.678884749 0x72485c7c8] dbg_complete: ep5in: trb ffffffc05a97d170 (E24:D24) buf 00000000edbb6600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.678958239 0x72485cd4b] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.678985634 0x72485cf59] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.679046832 0x72485d3f0] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 ZsI ==> 0
[ 1573.679070114 0x72485d5ae] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.679132041 0x72485da53] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.679221207 0x72485e104] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.679291676 0x72485e64d] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.679375999 0x72485eca0] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.679408395 0x72485ef0e] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.679506103 0x72485f662] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.679536312 0x72485f8a6] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.679623395 0x72485ff2e] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.679691728 0x72486044d] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.679726676 0x7248606ed] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.679788655 0x724860b92] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.679872509 0x7248611dd] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.679941884 0x724861711] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.680025947 0x724861d5f] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.680058187 0x724861fc9] dbg_trace_log_ctrl: Get String Descriptor(Index = 3, Length = 258)
[ 1573.680138082 0x7248625c8] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.680168655 0x724862813] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.680255114 0x724862e8f] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.680319489 0x724863363] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 18/18 ZsI ==> 0
[ 1573.680343291 0x72486352c] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.680406416 0x7248639e8] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.680488187 0x72486400a] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.680556207 0x724864524] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.680613551 0x724864971] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.680653239 0x724864c6b] dbg_prepare: ep5in: trb ffffffc05a97d180 (E25:D24) buf 00000000ee07f600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.680703187 0x72486502a] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.680729280 0x724865220] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.680761676 0x72486548c] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.680863395 0x724865c2e] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.680895009 0x724865e8c] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.680982926 0x724866525] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.681048655 0x724866a13] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.681084905 0x724866cca] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.681149437 0x7248671a2] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.681238916 0x724867858] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.681307457 0x724867d7c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.681391259 0x7248683c5] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.681422562 0x72486861e] dbg_trace_log_ctrl: Get Interface Status(Intf = 2, Length = 13)
[ 1573.681521259 0x724868d84] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.681553082 0x724868fe8] event (000010c0): ep0out: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.683232562 0x724870dde] event (00002040): ep0out: Transfer Complete (Sil) [Data Phase]
[ 1573.683309437 0x7248713a2] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 13/13 zsI ==> 0
[ 1573.683392197 0x7248719d7] event (000020c2): ep0in: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.683458291 0x724871ecc] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.683545478 0x724872556] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.683576780 0x7248727ae] dbg_complete: ep5in: trb ffffffc05a97d180 (E25:D25) buf 00000000ee07f600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.683631520 0x724872bca] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.683657718 0x724872dc1] event (0000c042): ep0in: Transfer Complete (sIL) [Status Phase]
[ 1573.683776937 0x7248736b2] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.683862770 0x724873d22] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.683895166 0x724873f90] dbg_trace_log_ctrl: Get Device Status(Length = 2)
[ 1573.683970322 0x724874533] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.683998343 0x72487474d] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.684084489 0x724874dc3] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.684147770 0x724875282] dbg_gadget_giveback: ep0out: req ffffff87cd156918 length 2/2 zsI ==> 0
[ 1573.684182509 0x72487551c] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.684207301 0x7248756f8] dbg_prepare: ep5in: trb ffffffc05a97d190 (E26:D25) buf 00000000ed16d600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.684238030 0x724875946] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.684253655 0x724875a72] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.684322718 0x724875fa0] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.684407822 0x724876603] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.684481624 0x724876b8c] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.684566416 0x7248771e8] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.684596937 0x724877432] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.684701207 0x724877c04] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.684732405 0x724877e5b] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.684821989 0x724878513] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.684851364 0x724878746] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.684913030 0x724878be6] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.684947718 0x724878e80] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.685010947 0x72487933e] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.686186103 0x72487eb61] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.686264593 0x72487f145] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.686539541 0x7248805e4] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.686570114 0x72488082e] dbg_trace_log_ctrl: Get String Descriptor(Index = 8, Length = 258)
[ 1573.686727666 0x724881400] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.686756989 0x724881633] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.686828395 0x724881b8d] event (00004096): ep5in: Transfer In Progress [0] (sIm)
[ 1573.686852301 0x724881d59] dbg_complete: ep5in: trb ffffffc05a97d190 (E26:D26) buf 00000000ed16d600 size 1x 0 ctrl 00000810 (hlcs:sC:normal)
[ 1573.686897457 0x7248820bb] dbg_gadget_giveback: ep5in: req ffffff87a6769000 length 8/8 zsI ==> 0
[ 1573.686922093 0x724882295] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.686947718 0x724882481] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.686996780 0x72488282f] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.687018343 0x7248829cd] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.687067822 0x724882d82] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.687139801 0x7248832e9] event (0000c040): ep0out: Transfer Complete (sIL) [Status Phase]
[ 1573.687193134 0x7248836e8] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.687263291 0x724883c2b] event (0000c040): ep0out: Transfer Complete (sIL) [Setup Phase]
[ 1573.687287145 0x724883df6] dbg_trace_log_ctrl: Clear Interface Feature(Function Suspend)
[ 1573.687372301 0x724884459] dbg_send_ep_cmd: ep0in: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.687400634 0x724884679] event (000010c2): ep0in: Transfer Not Ready [0] (Not Active) [Data Phase]
[ 1573.687471155 0x724884bc2] event (000090c2): ep0in: Transfer Not Ready [0] (Active) [Data Phase]
[ 1573.687495009 0x724884d8d] event (0000c042): ep0in: Transfer Complete (sIL) [Data Phase]
[ 1573.687544697 0x724885146] dbg_gadget_giveback: ep0out: req ffffff87a6768800 length 20/20 ZsI ==> 0
[ 1573.687593187 0x7248854e9] dbg_ep_queue: ep5in: req ffffff87a6769000 length 0/8 zsI ==> -115
[ 1573.687619645 0x7248856e6] dbg_prepare: ep5in: trb ffffffc05a97d1a0 (E27:D26) buf 00000000ee07f600 size 1x 8 ctrl 00000811 (Hlcs:sC:normal)
[ 1573.687660270 0x7248859f2] dbg_send_ep_cmd: ep5in: cmd 'Update Transfer' [b0007] params 00000000 00000000 00000000 --> status: Successful
[ 1573.687689437 0x724885c22] event (000020c0): ep0out: Transfer Not Ready [0] (Not Active) [Status Phase]
[ 1573.687738707 0x724885fd3] dbg_send_ep_cmd: ep0out: cmd 'Start Transfer' [406] params 00000000 efffa000 00000000 --> status: Successful
[ 1573.698040582 0x7248b6477] dbg_send_ep_cmd: ep1out: cmd 'End Transfer' [20c08] params 00000000 00000000 00000000 --> status: Timed Out
