Re: [PATCH v1 2/2] dt-bindings: usb: Add bindings doc for Sunplus USB HOST OHCI driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 14/03/2022 06:32, Vincent Shih wrote:
> Add bindings doc for Sunplus USB HOST OHCI driver
> 
> Signed-off-by: Vincent Shih <vincent.sunplus@xxxxxxxxx>
> ---
>  .../bindings/usb/sunplus,sp7021-usb-ohci.yaml      | 69 ++++++++++++++++++++++
>  MAINTAINERS                                        |  1 +
>  2 files changed, 70 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/sunplus,sp7021-usb-ohci.yaml
> 
> diff --git a/Documentation/devicetree/bindings/usb/sunplus,sp7021-usb-ohci.yaml b/Documentation/devicetree/bindings/usb/sunplus,sp7021-usb-ohci.yaml
> new file mode 100644
> index 0000000..7583b68
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/sunplus,sp7021-usb-ohci.yaml
> @@ -0,0 +1,69 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (C) Sunplus Co., Ltd. 2021
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/sunplus,sp7021-usb-ohci.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +

Looks good. Few minor nitpicks:

> +title: Sunplus SP7021 OHCI Controller Device Tree Bindings

Remove "Device Tree Bindings" words here. Title is about hardware.

> +
> +allOf:
> +  - $ref: usb-hcd.yaml#

Put entire "allOf:" just before "properties:".

> +
> +maintainers:
> +  - Vincent Shih <vincent.sunplus@xxxxxxxxx>
> +
> +description:
> +  Sunplus SP7021 USB HOST IP is a USB2.0 Host Controller. It supports both
> +  Enhanced Host Controller Interface (EHCI) and Open Host Controller Interface
> +  (OHCI).
> +
> +  It supports 32-bits address bus and 64bit data bus interface, compliant
> +  to AMBA AXI interface for data transfer.
> +
> +  It supports 32-bits address and data bus interface, compliant to AMBA
> +  AHB interface for register configurations.
> +
> +  It supports 32-bits address and data bus interface, compliant to AMBA
> +  AXI interface for register alternative configurations.
> +
> +  The UTM Interface block generates PHY control signals, compliant to
> +  USB2.0 Transceiver Macrocell Interface Specification Revision 1.0.
> +
> +properties:
> +  compatible:
> +    const: sunplus,sp7021-usb-ohci
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  resets:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1

You might need here phys. Are you sure you do not need to configure the
phy for OHCI? You should not assume it would be configured by other driver.

Best regards,
Krzysztof



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux