Hi Daehwan,
On 2/16/2022 9:52 PM, Jung Daehwan wrote:
> Hi wesley,
>
> On Tue, Feb 15, 2022 at 04:08:35PM -0800, Wesley Cheng wrote:
>> It is recommended by the Synopsis databook to issue a DCTL.CSftReset
>> when reconnecting from a device-initiated disconnect routine. This
>> resolves issues with enumeration during fast composition switching
>> cases, which result in an unknown device on the host.
>>
>> Signed-off-by: Wesley Cheng <quic_wcheng@xxxxxxxxxxx>
>> ---
>> drivers/usb/dwc3/core.c | 4 +---
>> drivers/usb/dwc3/core.h | 2 ++
>> drivers/usb/dwc3/gadget.c | 11 +++++++++++
>> 3 files changed, 14 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
>> index 18adddfba3da..02d10e1cb774 100644
>> --- a/drivers/usb/dwc3/core.c
>> +++ b/drivers/usb/dwc3/core.c
>> @@ -115,8 +115,6 @@ void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode)
>> dwc->current_dr_role = mode;
>> }
>>
>> -static int dwc3_core_soft_reset(struct dwc3 *dwc);
>> -
>> static void __dwc3_set_mode(struct work_struct *work)
>> {
>> struct dwc3 *dwc = work_to_dwc(work);
>> @@ -261,7 +259,7 @@ u32 dwc3_core_fifo_space(struct dwc3_ep *dep, u8 type)
>> * dwc3_core_soft_reset - Issues core soft reset and PHY reset
>> * @dwc: pointer to our context structure
>> */
>> -static int dwc3_core_soft_reset(struct dwc3 *dwc)
>> +int dwc3_core_soft_reset(struct dwc3 *dwc)
>> {
>> u32 reg;
>> int retries = 1000;
>> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
>> index 00348d6d479b..b27ad8dad317 100644
>> --- a/drivers/usb/dwc3/core.h
>> +++ b/drivers/usb/dwc3/core.h
>> @@ -1532,6 +1532,8 @@ bool dwc3_has_imod(struct dwc3 *dwc);
>> int dwc3_event_buffers_setup(struct dwc3 *dwc);
>> void dwc3_event_buffers_cleanup(struct dwc3 *dwc);
>>
>> +int dwc3_core_soft_reset(struct dwc3 *dwc);
>> +
>> #if IS_ENABLED(CONFIG_USB_DWC3_HOST) || IS_ENABLED(CONFIG_USB_DWC3_DUAL_ROLE)
>> int dwc3_host_init(struct dwc3 *dwc);
>> void dwc3_host_exit(struct dwc3 *dwc);
>> diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
>> index 0c89baedf220..788889f924f9 100644
>> --- a/drivers/usb/dwc3/gadget.c
>> +++ b/drivers/usb/dwc3/gadget.c
>> @@ -2585,6 +2585,17 @@ static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
>> dwc->ev_buf->length;
>> }
>> } else {
>> + /*
>> + * In the Synopsis DesignWare Cores USB3 Databook Rev. 1.90a
>> + * Section 4.1.9, it specifies that for a reconnect after a
>> + * device-initiated disconnect requires a core soft reset
>> + * (DCTL.CSftRst) before enabling the run/stop bit.
>> + */
>> + spin_unlock_irqrestore(&dwc->lock, flags);
>> + dwc3_core_soft_reset(dwc);
>> + spin_lock_irqsave(&dwc->lock, flags);
>> +
>> + dwc3_event_buffers_setup(dwc);
>
> Could you tell me why you add dwc3_event_buffer_setup?
>
During my testing if the event buffer re-initialization is not there,
then it resulted in the controller attempting to access an invalid
address space after the soft reset completed. (SMMU fault w/ FAR=0x0)
Likewise, in other scenarios where core soft reset is called, there is
always an event buffer re-init following it.
Thanks
Wesley Cheng
