On Tue, 2022-01-18 at 19:24 -0500, Sean Anderson wrote: > These clocks are not used by the dwc3-xilinx driver except to > enable/disable them. Move them to the dwc3 node so its driver can use > them to configure the reference clock period. > > Signed-off-by: Sean Anderson <sean.anderson@xxxxxxxx> > --- > > (no changes since v1) > > arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 ++-- > arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 4 ++-- > 2 files changed, 4 insertions(+), 4 deletions(-) > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi > b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi > index 1e0b1bca7c94..8493dd7d5f1f 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi > +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi > @@ -223,11 +223,11 @@ &uart1 { > clocks = <&zynqmp_clk UART1_REF>, <&zynqmp_clk LPD_LSBUS>; > }; > > -&usb0 { > +&dwc3_0 { > clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>; > }; > > -&usb1 { > +&dwc3_1 { > clocks = <&zynqmp_clk USB1_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>; > }; > > diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi > b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi > index 74e66443e4ce..ba68fb8529ee 100644 > --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi > +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi > @@ -811,7 +811,6 @@ usb0: usb@ff9d0000 { > status = "disabled"; > compatible = "xlnx,zynqmp-dwc3"; > reg = <0x0 0xff9d0000 0x0 0x100>; > - clock-names = "bus_clk", "ref_clk"; > power-domains = <&zynqmp_firmware PD_USB_0>; > resets = <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>, > <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>, > @@ -825,6 +824,7 @@ dwc3_0: usb@fe200000 { > interrupt-parent = <&gic>; > interrupt-names = "dwc_usb3", "otg"; > interrupts = <0 65 4>, <0 69 4>; > + clock-names = "bus_early", "ref"; > #stream-id-cells = <1>; > iommus = <&smmu 0x860>; > snps,quirk-frame-length-adjustment = <0x20>; > @@ -838,7 +838,6 @@ usb1: usb@ff9e0000 { > status = "disabled"; > compatible = "xlnx,zynqmp-dwc3"; > reg = <0x0 0xff9e0000 0x0 0x100>; > - clock-names = "bus_clk", "ref_clk"; > power-domains = <&zynqmp_firmware PD_USB_1>; > resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>, > <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>, > @@ -852,6 +851,7 @@ dwc3_1: usb@fe300000 { > interrupt-parent = <&gic>; > interrupt-names = "dwc_usb3", "otg"; > interrupts = <0 70 4>, <0 74 4>; > + clock-names = "bus_early", "ref"; > #stream-id-cells = <1>; > iommus = <&smmu 0x861>; > snps,quirk-frame-length-adjustment = <0x20>; Tested and working on ZynqMP. Reviewed-by: Robert Hancock <robert.hancock@xxxxxxxxxx> Tested-by: Robert Hancock <robert.hancock@xxxxxxxxxx>