Hi, Thanks for testing these.. On Wed, Dec 08, 2021 at 07:45:26PM -0800, Prashant Malani wrote: > Hi Heikki, > > On Tue, Dec 7, 2021 at 6:37 AM Heikki Krogerus > <heikki.krogerus@xxxxxxxxxxxxxxx> wrote: > > > > Hi, > > > > This removes the need for the drivers to always separately evaluate > > the _PLD. With the USB Type-C connector and USB port mapping this > > allows us to start using the component framework and remove the custom > > APIs. > > > > So far the only users of the _PLD information have been the USB > > drivers, but it seems it will be used also at least in some camera > > drivers later. These nevertheless touch mostly USB drivers. > > > > Rafael, is it still OK if Greg takes these? > > > > Prashant, can you test these? > > I've applied the patches to a system with the requisite _PLD entries > in firmware, and I'm not sure I can see the connectors getting created > correctly. > > My setup is: > > Chromebook ------> Dell WD19TB dock (in USB+DisplayPort Alternate > Mode) ----> USB Thumb drive. > > Here is the lsusb -t output before connecting the dock (omitting > unrelated busses): > localhost ~ # lsusb -t > /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/3p, 10000M/x2 > > Here is the lsusb -t output (omitting unrelated busses): > localhost ~ # lsusb -t > /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/3p, 10000M/x2 > |__ Port 2: Dev 15, If 0, Class=Hub, Driver=hub/4p, 10000M > |__ Port 3: Dev 16, If 0, Class=Hub, Driver=hub/4p, 5000M > |__ Port 3: Dev 18, If 0, Class=Mass Storage, > Driver=usb-storage, 5000M > |__ Port 4: Dev 17, If 0, Class=Vendor Specific Class, > Driver=r8152, 5000M > > I see the connector symlink for the root hub: > > localhost ~ # cd /sys/bus/usb/devices > localhost /sys/bus/usb/devices # ls 2-2/port/connector > data_role device firmware_node port1-cable port1-partner power > power_operation_mode power_role preferred_role subsystem > supported_accessory_modes uevent usb2-port2 usb3-port2 > usb_power_delivery_revision usb_typec_revision vconn_source > > But for none of the children devices: > > localhost /sys/bus/usb/devices # ls 2-2.3/port/connector > ls: cannot access '2-2.3/port/connector': No such file or directory > localhost /sys/bus/usb/devices # ls 2-2.3.3/port/connector > ls: cannot access '2-2.3.3/port/connector': No such file or directory > localhost /sys/bus/usb/devices # ls 2-2.3\:1.0/port/connector > ls: cannot access '2-2.3:1.0/port/connector': No such file or directory > localhost /sys/bus/usb/devices # ls 2-2.3.3\:1.0/port/connector > ls: cannot access '2-2.3.3:1.0/port/connector': No such file or directory > > Is this as you intended with the series? My interpretation was that > each connected usb device would get a "connector" symlink, but I may > have misinterpreted this. It is as intended. The usb ports on the board will have the connector symlink, not the devices attached to them - the firmware is only aware of the connectors on the board of course. It looks like this series is working as it should. If you want to extend this solution so that also every device in the usb topology will have the link to the connector on board, then that should be now possible, but that is out side of the scope of this series. You need to propose that separately. But I must ask, why can't you just walk down the topology until you reach the on-board ports that will have the connector links? thanks, -- heikki
