Re: [PATCH v8 3/4] arm64: dts: qcom: sc7280: Add PCIe nodes for IDP board

[Prasad Malisetty <pmaliset@xxxxxxxxxxxxxx>]

On 2021-09-21 01:21, Stephen Boyd wrote:
> Quoting Prasad Malisetty (2021-09-17 10:15:46)
> > diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi 
> > b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > index 99f9ee5..ee00df0 100644
> > --- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
> > @@ -199,6 +199,39 @@
> >         modem-init;
> >  };
> >
> > +&pcie1 {
> > +       status = "okay";
> > +
> > +       perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
> > +       pinctrl-0 = <&pcie1_default_state &nvme_ldo_enable_pin>;
> > +};
> > +
> > +&pcie1_phy {
> > +       status = "okay";
> > +
> > +       vdda-phy-supply = <&vreg_l10c_0p8>;
> > +       vdda-pll-supply = <&vreg_l6b_1p2>;
> > +};
> > +
> > +&pcie1_default_state {
> > +       reset-n {
> > +               pins = "gpio2";
> > +               function = "gpio";
> > +
> > +               drive-strength = <16>;
> > +               output-low;
> > +               bias-disable;
> > +       };
> > +
> > +       wake-n {
> > +               pins = "gpio3";
> > +               function = "gpio";
> > +
> > +               drive-strength = <2>;
> > +               bias-pull-up;
> > +       };
>
> I think the previous round of this series Bjorn was saying that these
> should be different nodes and tacked onto the pinctrl-0 list for the
> pcie1 device instead of adding them as subnodes of the "default state".

Hi Stephen,

Here NVMe gpio entry is endpoint related where as wake-n and reset-n are 
PCIe controller gpio's. I think Bjorn was saying keep endpoint related 
gpio (NVMe) in separate state entry in pinctrl-0 list.

Thanks
-Prasad.

> > +};
> > +
> >  &pmk8350_vadc {
> >         pmk8350_die_temp {
> >                 reg = <PMK8350_ADC7_DIE_TEMP>;
> > @@ -343,3 +376,10 @@
> >                 bias-pull-up;
> >         };
> >  };
> > +
> > +&tlmm {
> > +       nvme_ldo_enable_pin: nvme_ldo_enable_pin {
>
> Please use dashes where you use underscores in node names
>
>        nvme_ldo_enable_pin: nvme-ldo-enable-pin {
>
> > +               function = "gpio";
> > +               bias-pull-up;
>
> Of course with that said, the name of this node makes it sound like 
> this
> is a gpio controlled regulator. Why not use that binding then and 
> enable
> the regulator either by default with regulator properties like
> regulator-always-on and regulator-boot-enable and/or reference it from
> the pcie device somehow so that it can be turned off during suspend?
Agree, I will add in next patch series.

> > +       };
> > +};