Re: [PATCH v4 2/4] arm64: dts: qcom: sc7280: Add PCIe and PHY related nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Jul 16, 2021 at 07:28:45PM +0530, Prasad Malisetty wrote:
> Add PCIe controller and PHY nodes for sc7280 SOC.
> 
> Signed-off-by: Prasad Malisetty <pmaliset@xxxxxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/sc7280.dtsi | 125 +++++++++++++++++++++++++++++++++++
>  1 file changed, 125 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> index a8c274a..06baf88 100644
> --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
> @@ -15,6 +15,7 @@
>  #include <dt-bindings/reset/qcom,sdm845-pdc.h>
>  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>  #include <dt-bindings/thermal/thermal.h>
> +#include <dt-bindings/gpio/gpio.h>
>  
>  / {
>  	interrupt-parent = <&intc>;
> @@ -546,6 +547,118 @@
>  			#power-domain-cells = <1>;
>  		};
>  
> +		pcie1: pci@1c08000 {
> +			compatible = "qcom,pcie-sc7280", "qcom,pcie-sm8250", "snps,dw-pcie";
> +			reg = <0 0x01c08000 0 0x3000>,
> +			      <0 0x40000000 0 0xf1d>,
> +			      <0 0x40000f20 0 0xa8>,
> +			      <0 0x40001000 0 0x1000>,
> +			      <0 0x40100000 0 0x100000>;
> +
> +			reg-names = "parf", "dbi", "elbi", "atu", "config";
> +			device_type = "pci";
> +			linux,pci-domain = <1>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <2>;
> +
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
> +				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
> +
> +			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
> +				 <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
> +				 <&pcie1_lane 0>,
> +				 <&rpmhcc RPMH_CXO_CLK>,
> +				 <&gcc GCC_PCIE_1_AUX_CLK>,
> +				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
> +				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
> +				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
> +				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
> +				 <&gcc GCC_DDRSS_PCIE_SF_CLK>;
> +
> +			clock-names = "pipe",
> +				      "pipe_mux",
> +				      "phy_pipe",
> +				      "ref",
> +				      "aux",
> +				      "cfg",
> +				      "bus_master",
> +				      "bus_slave",
> +				      "slave_q2a",
> +				      "tbu",
> +				      "ddrss_sf_tbu";
> +
> +			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
> +			assigned-clock-rates = <19200000>;
> +
> +			resets = <&gcc GCC_PCIE_1_BCR>;
> +			reset-names = "pci";
> +
> +			power-domains = <&gcc GCC_PCIE_1_GDSC>;
> +
> +			phys = <&pcie1_lane>;
> +			phy-names = "pciephy";
> +
> +			perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pcie1_default_state>;
> +
> +			iommus = <&apps_smmu 0x1c80 0x1>;
> +
> +			iommu-map = <0x0 &apps_smmu 0x1c80 0x1>,
> +				    <0x100 &apps_smmu 0x1c81 0x1>;
> +
> +			status = "disabled";
> +		};
> +
> +		pcie1_phy: phy@1c0e000 {
> +			compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy";
> +			reg = <0 0x01c0e000 0 0x1c0>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
> +				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_CLKREF_EN>,
> +				 <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
> +			clock-names = "aux", "cfg_ahb", "ref", "refgen";
> +
> +			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
> +			reset-names = "phy";
> +
> +			assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>;
> +			assigned-clock-rates = <100000000>;
> +
> +			status = "disabled";
> +
> +			pcie1_lane: lanes@1c0e200 {
> +				reg = <0 0x01c0e200 0 0x170>,
> +				      <0 0x01c0e400 0 0x200>,
> +				      <0 0x01c0ea00 0 0x1f0>,
> +				      <0 0x01c0e600 0 0x170>,
> +				      <0 0x01c0e800 0 0x200>,
> +				      <0 0x01c0ee00 0 0xf4>;
> +				clocks = <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "pipe0";
> +
> +				#phy-cells = <0>;
> +				#clock-cells = <1>;
> +				clock-output-names = "pcie_1_pipe_clk";
> +			};
> +		};
> +
>  		stm@6002000 {
>  			compatible = "arm,coresight-stm", "arm,primecell";
>  			reg = <0 0x06002000 0 0x1000>,
> @@ -1185,6 +1298,18 @@
>  				pins = "gpio46", "gpio47";
>  				function = "qup13";
>  			};
> +
> +			pcie1_default_state: pcie1-default-state {
> +				clkreq {
> +					pins = "gpio79";
> +					function = "pcie1_clkreqn";
> +				};
> +
> +				wake-n {
> +					pins = "gpio3";
> +					function = "gpio";
> +				};

This could be essentially any GPIO, right? Does it really make sense to
have this node in the SoC file? I would say it belongs in the board file.



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux