Re: [PATCH] usb: hcd: Revert 306c54d0edb6ba94d39877524dddebaad7770cf2: Try MSI interrupts on PCI devices

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, 2021-07-13 at 15:15 -0400, Alan Stern wrote:
> On Tue, Jul 13, 2021 at 02:50:42PM -0400, Laurence Oberman wrote:
> > Customers have been reporting that the I/O is radically being
> > slowed down to HPE virtual USB ILO served DVD images during
> > installation.
> > 
> > Lots of investigation by the Red Hat lab has found that the issue
> > is 
> > because MSI edge interrupts do not work properly for these 
> > ILO USB devices.
> > We start fast and then drop to polling mode and its unusable.
> > 
> > The issue exists currently upstream on 5.13 as tested by Red Hat, 
> > and reverting the mentioned patch corrects this upstream.
> > 
> > David Jeffery has this explanation:
> > 
> > The problem with the patch turning on MSI appears to be that the
> > ehci 
> > driver (and possibly other usb controller types too) wasn't written
> > to
> > support edge-triggered interrupts.
> > The ehci_irq routine appears to be written in such a way that it
> > will 
> > be racy with multiple interrupt source bits.
> > With a level-triggered interrupt, it gets called another time and
> > cleans 
> > up other interrupt sources.
> > But with MSI edge, the interrupt state staying high results in no 
> > new interrupt and ehci has to run based on polling.
> > 
> > static irqreturn_t ehci_irq (struct usb_hcd *hcd)
> > {
> > ...
> >         status = ehci_readl(ehci, &ehci->regs->status);
> > 
> >         /* e.g. cardbus physical eject */
> >         if (status == ~(u32) 0) {
> >                 ehci_dbg (ehci, "device removed\n");
> >                 goto dead;
> >         }
> > 
> >         /*
> >          * We don't use STS_FLR, but some controllers don't like it
> > to
> >          * remain on, so mask it out along with the other status
> > bits.
> >          */
> >         masked_status = status & (INTR_MASK | STS_FLR);
> > 
> >         /* Shared IRQ? */
> >         if (!masked_status || unlikely(ehci->rh_state ==
> > EHCI_RH_HALTED)) {
> >                 spin_unlock_irqrestore(&ehci->lock, flags);
> >                 return IRQ_NONE;
> >         }
> > 
> >         /* clear (just) interrupts */
> >         ehci_writel(ehci, masked_status, &ehci->regs->status);
> > ...
> > 
> > ehci_irq() reads the interrupt status register and then writes the
> > active 
> > interrupt-related bits back out to ack the interrupt cause.
> > But with an edge interrupt, this is racy as another source of
> > interrupt 
> > could be raised by ehci between the read and the write reaching
> > the 
> > hardware. 
> > e.g.  If STS_IAA was set during the initial read, but some other
> > bit like 
> > STS_INT gets raised by the hardware between the read and the write
> > to the 
> > interrupt status register, the interrupt signal state won't drop.
> > The interrupt state says high, and since it is now edged triggered
> > with 
> > MSI, no new invocation of the interrupt handler gets triggered.
> 
> Wouldn't it be better to change these other PCI drivers by adding 
> proper MSI support?  I don't know what would be involved, but 
> presumably it wouldn't be very hard.  (Just run the handler in a
> loop 
> until all the interrupt status bits are off?)
> 
> Alan Stern
> 

Hello

Agree with you that is a big hammer approach,  but it's such a key
piece of the massive number of HPE servers out there and we have many
affected customers.

While I did all the test work and discovery etc, I am definitely not a
USB kernel guy very often, I spend most of my time in storage.
I will listen for the other replies to see how the folks who know the
subsystem better than I would want this reolved.

Thanks
Laurence






[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux