Hi Marek,
thank you for your feedback.
On Fri, Jun 18, 2021 at 10:39:12AM +0200, Marek Szyprowski wrote:
> Hi Oleksij,
>
> On 07.06.2021 10:27, Oleksij Rempel wrote:
> > To be able to use ax88772 with external PHYs and use advantage of
> > existing PHY drivers, we need to port at least ax88772 part of asix
> > driver to the phylib framework.
> >
> > Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
>
> I found one more issue with this patch. On one of my test boards
> (Samsung Exynos5250 SoC based Arndale) system fails to establish network
> connection just after starting the kernel when the driver is build-in.
>
> --->8---
> # dmesg | grep asix
> [ 2.761928] usbcore: registered new interface driver asix
> [ 5.003110] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized):
> invalid hw address, using random
> [ 6.065400] asix 1-3.2.4:1.0 eth0: register 'asix' at
> usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 7a:9b:9a:f2:94:8e
> [ 14.043868] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow
> control off
> # ping -c2 host
> PING host (192.168.100.1) 56(84) bytes of data.
> From 192.168.100.20 icmp_seq=1 Destination Host Unreachable
> From 192.168.100.20 icmp_seq=2 Destination Host Unreachable
>
> --- host ping statistics ---
> 2 packets transmitted, 0 received, +2 errors, 100% packet loss, time 59ms
> --->8---
Hm... it looks like different chip variant. My is registered as
"ASIX AX88772B USB", yours is "ASIX AX88772 USB 2.0" - "B" is the
difference. Can you please tell me more about this adapter and if possible open
tell the real part name.
I can imagine that this adapter may using generic PHY driver.
Can you please confirm it by dmesg | grep PHY?
In my case i'll get:
Asix Electronics AX88772C usb-001:003:10: attached PHY driver (mii_bus:phy_addr=usb-001:003:10, irq=POLL)
If you have a different PHY, can you please send me the PHY id:
cat /sys/bus/mdio_bus/devices/usb-001\:003\:10/phy_id
Your usb path will probably be different.
> Calling ifup eth0 && ifdown eth0 fixes the network status:
>
> --->8---
> # ifdown eth0 && ifup eth0
> [ 60.474929] asix 1-3.2.4:1.0 eth0: Link is Down
> [ 60.623516] asix 1-3.2.4:1.0 eth0: Link is Down
> [ 62.774304] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 62.786354] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow
> control off
> # ping -c2 host
> PING host (192.168.100.1) 56(84) bytes of data.
> 64 bytes from host (192.168.100.1): icmp_seq=1 ttl=64 time=1.25 ms
> 64 bytes from host (192.168.100.1): icmp_seq=2 ttl=64 time=0.853 ms
>
> --- host ping statistics ---
> 2 packets transmitted, 2 received, 0% packet loss, time 3ms
> rtt min/avg/max/mdev = 0.853/1.053/1.254/0.203 ms
> --->8---
>
> When driver is loaded as a module (and without any other modules, so
> this is not a dependency issue), the connection is established properly
> just after the boot:
>
> --->8---
> # dmesg | grep asix
> [ 13.633284] asix 1-3.2.4:1.0 (unnamed net_device) (uninitialized):
> invalid hw address, using random
> [ 15.390350] asix 1-3.2.4:1.0 eth0: register 'asix' at
> usb-12110000.usb-3.2.4, ASIX AX88772 USB 2.0 Ethernet, 3a:51:11:08:aa:ea
> [ 15.414052] usbcore: registered new interface driver asix
> [ 15.832564] asix 1-3.2.4:1.0 eth0: Link is Down
> [ 18.053747] asix 1-3.2.4:1.0 eth0: Link is Up - 100Mbps/Full - flow
> control off
> # ping -c2 host
> PING host (192.168.100.1) 56(84) bytes of data.
> 64 bytes from host (192.168.100.1): icmp_seq=1 ttl=64 time=0.545 ms
> 64 bytes from host (192.168.100.1): icmp_seq=2 ttl=64 time=0.742 ms
>
> --- host ping statistics ---
> 2 packets transmitted, 2 received, 0% packet loss, time 3ms
> rtt min/avg/max/mdev = 0.545/0.643/0.742/0.101 ms
>
> --->8---
>
> Let me know if I can make any other tests that would help fixing this issue.
>
> > ---
> > drivers/net/usb/asix.h | 9 +++
> > drivers/net/usb/asix_common.c | 37 ++++++++++
> > drivers/net/usb/asix_devices.c | 120 +++++++++++++++++++++------------
> > drivers/net/usb/ax88172a.c | 14 ----
> > 4 files changed, 122 insertions(+), 58 deletions(-)
> >
> > diff --git a/drivers/net/usb/asix.h b/drivers/net/usb/asix.h
> > index edb94efd265e..2122d302e643 100644
> > --- a/drivers/net/usb/asix.h
> > +++ b/drivers/net/usb/asix.h
> > @@ -25,6 +25,7 @@
> > #include <linux/usb/usbnet.h>
> > #include <linux/slab.h>
> > #include <linux/if_vlan.h>
> > +#include <linux/phy.h>
> >
> > #define DRIVER_VERSION "22-Dec-2011"
> > #define DRIVER_NAME "asix"
> > @@ -178,6 +179,10 @@ struct asix_common_private {
> > u16 presvd_phy_advertise;
> > u16 presvd_phy_bmcr;
> > struct asix_rx_fixup_info rx_fixup_info;
> > + struct mii_bus *mdio;
> > + struct phy_device *phydev;
> > + u16 phy_addr;
> > + char phy_name[20];
> > };
> >
> > extern const struct driver_info ax88172a_info;
> > @@ -214,6 +219,7 @@ int asix_write_rx_ctl(struct usbnet *dev, u16 mode, int in_pm);
> >
> > u16 asix_read_medium_status(struct usbnet *dev, int in_pm);
> > int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm);
> > +void asix_adjust_link(struct net_device *netdev);
> >
> > int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm);
> >
> > @@ -222,6 +228,9 @@ void asix_set_multicast(struct net_device *net);
> > int asix_mdio_read(struct net_device *netdev, int phy_id, int loc);
> > void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val);
> >
> > +int asix_mdio_bus_read(struct mii_bus *bus, int phy_id, int regnum);
> > +int asix_mdio_bus_write(struct mii_bus *bus, int phy_id, int regnum, u16 val);
> > +
> > int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc);
> > void asix_mdio_write_nopm(struct net_device *netdev, int phy_id, int loc,
> > int val);
> > diff --git a/drivers/net/usb/asix_common.c b/drivers/net/usb/asix_common.c
> > index e1109f1a8dd5..085bc8281082 100644
> > --- a/drivers/net/usb/asix_common.c
> > +++ b/drivers/net/usb/asix_common.c
> > @@ -384,6 +384,27 @@ int asix_write_medium_mode(struct usbnet *dev, u16 mode, int in_pm)
> > return ret;
> > }
> >
> > +/* set MAC link settings according to information from phylib */
> > +void asix_adjust_link(struct net_device *netdev)
> > +{
> > + struct phy_device *phydev = netdev->phydev;
> > + struct usbnet *dev = netdev_priv(netdev);
> > + u16 mode = 0;
> > +
> > + if (phydev->link) {
> > + mode = AX88772_MEDIUM_DEFAULT;
> > +
> > + if (phydev->duplex == DUPLEX_HALF)
> > + mode &= ~AX_MEDIUM_FD;
> > +
> > + if (phydev->speed != SPEED_100)
> > + mode &= ~AX_MEDIUM_PS;
> > + }
> > +
> > + asix_write_medium_mode(dev, mode, 0);
> > + phy_print_status(phydev);
> > +}
> > +
> > int asix_write_gpio(struct usbnet *dev, u16 value, int sleep, int in_pm)
> > {
> > int ret;
> > @@ -506,6 +527,22 @@ void asix_mdio_write(struct net_device *netdev, int phy_id, int loc, int val)
> > mutex_unlock(&dev->phy_mutex);
> > }
> >
> > +/* MDIO read and write wrappers for phylib */
> > +int asix_mdio_bus_read(struct mii_bus *bus, int phy_id, int regnum)
> > +{
> > + struct usbnet *priv = bus->priv;
> > +
> > + return asix_mdio_read(priv->net, phy_id, regnum);
> > +}
> > +
> > +int asix_mdio_bus_write(struct mii_bus *bus, int phy_id, int regnum, u16 val)
> > +{
> > + struct usbnet *priv = bus->priv;
> > +
> > + asix_mdio_write(priv->net, phy_id, regnum, val);
> > + return 0;
> > +}
> > +
> > int asix_mdio_read_nopm(struct net_device *netdev, int phy_id, int loc)
> > {
> > struct usbnet *dev = netdev_priv(netdev);
> > diff --git a/drivers/net/usb/asix_devices.c b/drivers/net/usb/asix_devices.c
> > index 00b6ac0570eb..e4cd85e38edd 100644
> > --- a/drivers/net/usb/asix_devices.c
> > +++ b/drivers/net/usb/asix_devices.c
> > @@ -285,7 +285,7 @@ static int ax88172_bind(struct usbnet *dev, struct usb_interface *intf)
> >
> > static const struct ethtool_ops ax88772_ethtool_ops = {
> > .get_drvinfo = asix_get_drvinfo,
> > - .get_link = asix_get_link,
> > + .get_link = usbnet_get_link,
> > .get_msglevel = usbnet_get_msglevel,
> > .set_msglevel = usbnet_set_msglevel,
> > .get_wol = asix_get_wol,
> > @@ -293,37 +293,15 @@ static const struct ethtool_ops ax88772_ethtool_ops = {
> > .get_eeprom_len = asix_get_eeprom_len,
> > .get_eeprom = asix_get_eeprom,
> > .set_eeprom = asix_set_eeprom,
> > - .nway_reset = usbnet_nway_reset,
> > - .get_link_ksettings = usbnet_get_link_ksettings_mii,
> > - .set_link_ksettings = usbnet_set_link_ksettings_mii,
> > + .nway_reset = phy_ethtool_nway_reset,
> > + .get_link_ksettings = phy_ethtool_get_link_ksettings,
> > + .set_link_ksettings = phy_ethtool_set_link_ksettings,
> > };
> >
> > -static int ax88772_link_reset(struct usbnet *dev)
> > -{
> > - u16 mode;
> > - struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET };
> > -
> > - mii_check_media(&dev->mii, 1, 1);
> > - mii_ethtool_gset(&dev->mii, &ecmd);
> > - mode = AX88772_MEDIUM_DEFAULT;
> > -
> > - if (ethtool_cmd_speed(&ecmd) != SPEED_100)
> > - mode &= ~AX_MEDIUM_PS;
> > -
> > - if (ecmd.duplex != DUPLEX_FULL)
> > - mode &= ~AX_MEDIUM_FD;
> > -
> > - netdev_dbg(dev->net, "ax88772_link_reset() speed: %u duplex: %d setting mode to 0x%04x\n",
> > - ethtool_cmd_speed(&ecmd), ecmd.duplex, mode);
> > -
> > - asix_write_medium_mode(dev, mode, 0);
> > -
> > - return 0;
> > -}
> > -
> > static int ax88772_reset(struct usbnet *dev)
> > {
> > struct asix_data *data = (struct asix_data *)&dev->data;
> > + struct asix_common_private *priv = dev->driver_priv;
> > int ret;
> >
> > /* Rewrite MAC address */
> > @@ -342,6 +320,8 @@ static int ax88772_reset(struct usbnet *dev)
> > if (ret < 0)
> > goto out;
> >
> > + phy_start(priv->phydev);
> > +
> > return 0;
> >
> > out:
> > @@ -586,7 +566,7 @@ static const struct net_device_ops ax88772_netdev_ops = {
> > .ndo_get_stats64 = dev_get_tstats64,
> > .ndo_set_mac_address = asix_set_mac_address,
> > .ndo_validate_addr = eth_validate_addr,
> > - .ndo_do_ioctl = asix_ioctl,
> > + .ndo_do_ioctl = phy_do_ioctl_running,
> > .ndo_set_rx_mode = asix_set_multicast,
> > };
> >
> > @@ -677,12 +657,57 @@ static int asix_resume(struct usb_interface *intf)
> > return usbnet_resume(intf);
> > }
> >
> > +static int ax88772_init_mdio(struct usbnet *dev)
> > +{
> > + struct asix_common_private *priv = dev->driver_priv;
> > +
> > + priv->mdio = devm_mdiobus_alloc(&dev->udev->dev);
> > + if (!priv->mdio)
> > + return -ENOMEM;
> > +
> > + priv->mdio->priv = dev;
> > + priv->mdio->read = &asix_mdio_bus_read;
> > + priv->mdio->write = &asix_mdio_bus_write;
> > + priv->mdio->name = "Asix MDIO Bus";
> > + /* mii bus name is usb-<usb bus number>-<usb device number> */
> > + snprintf(priv->mdio->id, MII_BUS_ID_SIZE, "usb-%03d:%03d",
> > + dev->udev->bus->busnum, dev->udev->devnum);
> > +
> > + return devm_mdiobus_register(&dev->udev->dev, priv->mdio);
> > +}
> > +
> > +static int ax88772_init_phy(struct usbnet *dev)
> > +{
> > + struct asix_common_private *priv = dev->driver_priv;
> > + int ret;
> > +
> > + priv->phy_addr = asix_read_phy_addr(dev, true);
> > + if (priv->phy_addr < 0)
> > + return priv->phy_addr;
> > +
> > + snprintf(priv->phy_name, sizeof(priv->phy_name), PHY_ID_FMT,
> > + priv->mdio->id, priv->phy_addr);
> > +
> > + priv->phydev = phy_connect(dev->net, priv->phy_name, &asix_adjust_link,
> > + PHY_INTERFACE_MODE_INTERNAL);
> > + if (IS_ERR(priv->phydev)) {
> > + netdev_err(dev->net, "Could not connect to PHY device %s\n",
> > + priv->phy_name);
> > + ret = PTR_ERR(priv->phydev);
> > + return ret;
> > + }
> > +
> > + phy_attached_info(priv->phydev);
> > +
> > + return 0;
> > +}
> > +
> > static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
> > {
> > - int ret, i;
> > u8 buf[ETH_ALEN] = {0}, chipcode = 0;
> > - u32 phyid;
> > struct asix_common_private *priv;
> > + int ret, i;
> > + u32 phyid;
> >
> > usbnet_get_endpoints(dev, intf);
> >
> > @@ -714,17 +739,6 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
> >
> > asix_set_netdev_dev_addr(dev, buf);
> >
> > - /* Initialize MII structure */
> > - dev->mii.dev = dev->net;
> > - dev->mii.mdio_read = asix_mdio_read;
> > - dev->mii.mdio_write = asix_mdio_write;
> > - dev->mii.phy_id_mask = 0x1f;
> > - dev->mii.reg_num_mask = 0x1f;
> > -
> > - dev->mii.phy_id = asix_read_phy_addr(dev, true);
> > - if (dev->mii.phy_id < 0)
> > - return dev->mii.phy_id;
> > -
> > dev->net->netdev_ops = &ax88772_netdev_ops;
> > dev->net->ethtool_ops = &ax88772_ethtool_ops;
> > dev->net->needed_headroom = 4; /* cf asix_tx_fixup() */
> > @@ -768,11 +782,31 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
> > priv->suspend = ax88772_suspend;
> > }
> >
> > + ret = ax88772_init_mdio(dev);
> > + if (ret)
> > + return ret;
> > +
> > + return ax88772_init_phy(dev);
> > +}
> > +
> > +static int ax88772_stop(struct usbnet *dev)
> > +{
> > + struct asix_common_private *priv = dev->driver_priv;
> > +
> > + /* On unplugged USB, we will get MDIO communication errors and the
> > + * PHY will be set in to PHY_HALTED state.
> > + */
> > + if (priv->phydev->state != PHY_HALTED)
> > + phy_stop(priv->phydev);
> > +
> > return 0;
> > }
> >
> > static void ax88772_unbind(struct usbnet *dev, struct usb_interface *intf)
> > {
> > + struct asix_common_private *priv = dev->driver_priv;
> > +
> > + phy_disconnect(priv->phydev);
> > asix_rx_fixup_common_free(dev->driver_priv);
> > }
> >
> > @@ -1161,8 +1195,8 @@ static const struct driver_info ax88772_info = {
> > .bind = ax88772_bind,
> > .unbind = ax88772_unbind,
> > .status = asix_status,
> > - .link_reset = ax88772_link_reset,
> > .reset = ax88772_reset,
> > + .stop = ax88772_stop,
> > .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR | FLAG_MULTI_PACKET,
> > .rx_fixup = asix_rx_fixup_common,
> > .tx_fixup = asix_tx_fixup,
> > @@ -1173,7 +1207,6 @@ static const struct driver_info ax88772b_info = {
> > .bind = ax88772_bind,
> > .unbind = ax88772_unbind,
> > .status = asix_status,
> > - .link_reset = ax88772_link_reset,
> > .reset = ax88772_reset,
> > .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
> > FLAG_MULTI_PACKET,
> > @@ -1209,7 +1242,6 @@ static const struct driver_info hg20f9_info = {
> > .bind = ax88772_bind,
> > .unbind = ax88772_unbind,
> > .status = asix_status,
> > - .link_reset = ax88772_link_reset,
> > .reset = ax88772_reset,
> > .flags = FLAG_ETHER | FLAG_FRAMING_AX | FLAG_LINK_INTR |
> > FLAG_MULTI_PACKET,
> > diff --git a/drivers/net/usb/ax88172a.c b/drivers/net/usb/ax88172a.c
> > index c8ca5187eece..2e2081346740 100644
> > --- a/drivers/net/usb/ax88172a.c
> > +++ b/drivers/net/usb/ax88172a.c
> > @@ -25,20 +25,6 @@ struct ax88172a_private {
> > struct asix_rx_fixup_info rx_fixup_info;
> > };
> >
> > -/* MDIO read and write wrappers for phylib */
> > -static int asix_mdio_bus_read(struct mii_bus *bus, int phy_id, int regnum)
> > -{
> > - return asix_mdio_read(((struct usbnet *)bus->priv)->net, phy_id,
> > - regnum);
> > -}
> > -
> > -static int asix_mdio_bus_write(struct mii_bus *bus, int phy_id, int regnum,
> > - u16 val)
> > -{
> > - asix_mdio_write(((struct usbnet *)bus->priv)->net, phy_id, regnum, val);
> > - return 0;
> > -}
> > -
> > /* set MAC link settings according to information from phylib */
> > static void ax88172a_adjust_link(struct net_device *netdev)
> > {
>
> Best regards
> --
> Marek Szyprowski, PhD
> Samsung R&D Institute Poland
>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
