On Tue, Jun 15, 2021 at 12:52 AM Badhri Jagan Sridharan
<badhri@xxxxxxxxxx> wrote:
>
> Hi Kyle,
>
> The change doesn't seem to handle the cases where the partner does not
> accept the request i.e.
> "case PD_CTRL_REJECT:
> case PD_CTRL_WAIT:
> case PD_CTRL_NOT_SUPP:"
> We should fall back to the disconnect threshold based on the
> previously negotiated voltage levels in those cases.
>
> Regards,
> Badhri
>
>
> On Sun, Jun 13, 2021 at 8:13 AM Kyle Tso <kyletso@xxxxxxxxxx> wrote:
> >
> > If the voltage is being decreased in power negotiation, the Source will
> > set the power supply to operate at the new voltage level before sending
> > PS_RDY. Relax the disconnect threshold for Sink after receiving Accept
> > Message to ensure the relaxed setting is enabled before the voltage
> > collapse. And the real threshold will be set after Sink receives PS_RDY
> > Message.
> >
> > Fixes: f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
> > Cc: Badhri Jagan Sridharan <badhri@xxxxxxxxxx>
> > Signed-off-by: Kyle Tso <kyletso@xxxxxxxxxx>
> > ---
> > drivers/usb/typec/tcpm/tcpm.c | 4 ++++
> > 1 file changed, 4 insertions(+)
> >
> > diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> > index 0db685d5d9c0..9f3f37da71b6 100644
> > --- a/drivers/usb/typec/tcpm/tcpm.c
> > +++ b/drivers/usb/typec/tcpm/tcpm.c
> > @@ -2646,6 +2646,8 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
> > switch (port->state) {
> > case SNK_NEGOTIATE_CAPABILITIES:
> > port->pps_data.active = false;
> > + /* Voltage is going to be at new level. Relax the threshold here. */
> > + tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
> > tcpm_set_state(port, SNK_TRANSITION_SINK, 0);
> > break;
> > case SNK_NEGOTIATE_PPS_CAPABILITIES:
> > @@ -2656,6 +2658,8 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
> > port->req_supply_voltage = port->pps_data.req_out_volt;
> > port->req_current_limit = port->pps_data.req_op_curr;
> > power_supply_changed(port->psy);
> > + /* Voltage is going to be at new level. Relax the threshold here. */
> > + tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
> > tcpm_set_state(port, SNK_TRANSITION_SINK, 0);
> > break;
Yes, Badhri you are right.
And it's still too late for PPS power negotiation. The Source begins
to lower it's Vbus level just after Accept Message.
I will send patch v2 to fix these problems.
thanks,
Kyle
> > case SOFT_RESET_SEND:
> > --
> > 2.32.0.272.g935e593368-goog
> >
