Re: [PATCH] USB: serial: cp210x: fix CP2102N-A01 modem control

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



El 9/6/21 a las 11:15, Johan Hovold escribió:
CP2102N revision A01 (firmware version <= 1.0.4) has a buggy
flow-control implementation that uses the ulXonLimit instead of
ulFlowReplace field of the flow-control settings structure (erratum
CP2102N_E104).

A recent change that set the input software flow-control limits
incidentally broke RTS control for these devices when CRTSCTS is not set
as the new limits would always enable hardware flow control.

Fix this by explicitly disabling flow control for the buggy firmware
versions and only updating the input software flow-control limits when
IXOFF is requested. This makes sure that the terminal settings matches
the default zero ulXonLimit (ulFlowReplace) for these devices.

Reported-by: David Frey <dpfrey@xxxxxxxxx>
Reported-by: Alex Villacís Lasso <a_villacis@xxxxxxxxxxxxx>
Fixes: f61309d9c96a ("USB: serial: cp210x: set IXOFF thresholds")
Cc: stable@xxxxxxxxxxxxxxx      # 5.12
Signed-off-by: Johan Hovold <johan@xxxxxxxxxx>
---
  drivers/usb/serial/cp210x.c | 64 ++++++++++++++++++++++++++++++++++---
  1 file changed, 59 insertions(+), 5 deletions(-)

David and Alex,

Would you mind testing this one with your CP2108N-A01? I've verified it
against a CP2108N-A02 (fw 1.0.8) here.

Johan


diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c
index ee595d1bea0a..910bc965e6cd 100644
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -252,9 +252,11 @@ struct cp210x_serial_private {
  	u8			gpio_input;
  #endif
  	u8			partnum;
+	u32			fw_version;
  	speed_t			min_speed;
  	speed_t			max_speed;
  	bool			use_actual_rate;
+	bool			no_flow_control;
  };
enum cp210x_event_state {
@@ -398,6 +400,7 @@ struct cp210x_special_chars {
/* CP210X_VENDOR_SPECIFIC values */
  #define CP210X_READ_2NCONFIG	0x000E
+#define CP210X_GET_FW_VER_2N	0x0010
  #define CP210X_READ_LATCH	0x00C2
  #define CP210X_GET_PARTNUM	0x370B
  #define CP210X_GET_PORTCONFIG	0x370C
@@ -1122,6 +1125,7 @@ static bool cp210x_termios_change(const struct ktermios *a, const struct ktermio
  static void cp210x_set_flow_control(struct tty_struct *tty,
  		struct usb_serial_port *port, struct ktermios *old_termios)
  {
+	struct cp210x_serial_private *priv = usb_get_serial_data(port->serial);
  	struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
  	struct cp210x_special_chars chars;
  	struct cp210x_flow_ctl flow_ctl;
@@ -1129,6 +1133,15 @@ static void cp210x_set_flow_control(struct tty_struct *tty,
  	u32 ctl_hs;
  	int ret;
+ /*
+	 * Some CP2102N interpret ulXonLimit as ulFlowReplace (erratum
+	 * CP2102N_E104). Report back that flow control is not supported.
+	 */
+	if (priv->no_flow_control) {
+		tty->termios.c_cflag &= ~CRTSCTS;
+		tty->termios.c_iflag &= ~(IXON | IXOFF);
+	}
+
  	if (old_termios &&
  			C_CRTSCTS(tty) == (old_termios->c_cflag & CRTSCTS) &&
  			I_IXON(tty) == (old_termios->c_iflag & IXON) &&
@@ -1185,19 +1198,20 @@ static void cp210x_set_flow_control(struct tty_struct *tty,
  		port_priv->crtscts = false;
  	}
- if (I_IXOFF(tty))
+	if (I_IXOFF(tty)) {
  		flow_repl |= CP210X_SERIAL_AUTO_RECEIVE;
-	else
+
+		flow_ctl.ulXonLimit = cpu_to_le32(128);
+		flow_ctl.ulXoffLimit = cpu_to_le32(128);
+	} else {
  		flow_repl &= ~CP210X_SERIAL_AUTO_RECEIVE;
+	}
if (I_IXON(tty))
  		flow_repl |= CP210X_SERIAL_AUTO_TRANSMIT;
  	else
  		flow_repl &= ~CP210X_SERIAL_AUTO_TRANSMIT;
- flow_ctl.ulXonLimit = cpu_to_le32(128);
-	flow_ctl.ulXoffLimit = cpu_to_le32(128);
-
  	dev_dbg(&port->dev, "%s - ctrl = 0x%02x, flow = 0x%02x\n", __func__,
  			ctl_hs, flow_repl);
@@ -1908,6 +1922,45 @@ static void cp210x_init_max_speed(struct usb_serial *serial)
  	priv->use_actual_rate = use_actual_rate;
  }
+static int cp210x_get_fw_version(struct usb_serial *serial, u16 value)
+{
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+	u8 ver[3];
+	int ret;
+
+	ret = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST, value,
+			ver, sizeof(ver));
+	if (ret)
+		return ret;
+
+	dev_dbg(&serial->interface->dev, "%s - %d.%d.%d\n", __func__,
+			ver[0], ver[1], ver[2]);
+
+	priv->fw_version = ver[0] << 16 | ver[1] << 8 | ver[2];
+
+	return 0;
+}
+
+static void cp210x_determine_quirks(struct usb_serial *serial)
+{
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+	int ret;
+
+	switch (priv->partnum) {
+	case CP210X_PARTNUM_CP2102N_QFN28:
+	case CP210X_PARTNUM_CP2102N_QFN24:
+	case CP210X_PARTNUM_CP2102N_QFN20:
+		ret = cp210x_get_fw_version(serial, CP210X_GET_FW_VER_2N);
+		if (ret)
+			break;
+		if (priv->fw_version <= 0x10004)
+			priv->no_flow_control = true;
+		break;
+	default:
+		break;
+	}
+}
+
  static int cp210x_attach(struct usb_serial *serial)
  {
  	int result;
@@ -1928,6 +1981,7 @@ static int cp210x_attach(struct usb_serial *serial)
usb_set_serial_data(serial, priv); + cp210x_determine_quirks(serial);
  	cp210x_init_max_speed(serial);
result = cp210x_gpio_init(serial);

Applied patch and tested with ESP32 board under kernel 5.12.9:


# echo module cp210x +p > /sys/kernel/debug/dynamic_debug/control ; insmod ./cp210x.ko dyndbg==p

jun 09 11:51:52 karlalex-asus kernel: usbcore: registered new interface driver cp210x jun 09 11:51:52 karlalex-asus kernel: usbserial: USB Serial support registered for cp210x


<device plugged in>

jun 09 11:56:00 karlalex-asus kernel: usb 1-9: new full-speed USB device number 6 using xhci_hcd jun 09 11:56:00 karlalex-asus kernel: usb 1-9: New USB device found, idVendor=10c4, idProduct=ea60, bcdDevice= 1.00 jun 09 11:56:00 karlalex-asus kernel: usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=3 jun 09 11:56:00 karlalex-asus kernel: usb 1-9: Product: CP2102N USB to UART Bridge Controller
jun 09 11:56:00 karlalex-asus kernel: usb 1-9: Manufacturer: Silicon Labs
jun 09 11:56:00 karlalex-asus kernel: usb 1-9: SerialNumber: 283405bafee6e81182024fe64b629a73 jun 09 11:56:00 karlalex-asus kernel: cp210x 1-9:1.0: cp210x converter detected jun 09 11:56:00 karlalex-asus kernel: cp210x 1-9:1.0: cp210x_get_fw_version - 1.0.4 jun 09 11:56:00 karlalex-asus kernel: usb 1-9: cp210x converter now attached to ttyUSB0 jun 09 11:56:00 karlalex-asus mtp-probe[15041]: checking bus 1, device 6: "/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9" jun 09 11:56:00 karlalex-asus mtp-probe[15041]: bus: 1, device: 6 was not an MTP device jun 09 11:56:00 karlalex-asus mtp-probe[15060]: checking bus 1, device 6: "/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9" jun 09 11:56:00 karlalex-asus mtp-probe[15060]: bus: 1, device: 6 was not an MTP device jun 09 11:56:02 karlalex-asus ModemManager[726]: <info> [base-manager] couldn't check support for device '/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9': not supported by any plugin


$ miniterm.py /dev/ttyUSB0 115200
<successful connect>

jun 09 11:56:50 karlalex-asus kernel: cp210x ttyUSB0: cp210x_change_speed - setting baud rate to 9600 jun 09 11:56:50 karlalex-asus kernel: cp210x ttyUSB0: cp210x_set_flow_control - ctrl = 0x00, flow = 0x00 jun 09 11:56:50 karlalex-asus kernel: cp210x ttyUSB0: cp210x_tiocmset_port - control = 0x0303 jun 09 11:56:50 karlalex-asus kernel: cp210x ttyUSB0: cp210x_change_speed - setting baud rate to 115384 jun 09 11:56:50 karlalex-asus kernel: cp210x ttyUSB0: cp210x_tiocmset_port - control = 0x0101 jun 09 11:56:50 karlalex-asus kernel: cp210x ttyUSB0: cp210x_tiocmset_port - control = 0x0202


At least in my case, this patch fixes the regression for my workflow.




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux