Hi, On Wed, May 05, 2021 at 10:50:01AM +0200, Oliver Neukum wrote: > Am Dienstag, den 04.05.2021, 18:52 +0100 schrieb Sean Young: > > See http://www.usbuirt.com/ > > > > Hi, > > nice driver, just a few issues. > I have marked them inline. Thank you for the review, I appreciate it. > Regards > Oliver > > > + > > +#define WDR_TIMEOUT 5000 /* default urb timeout */ > > That is the default ctrl timeout. Do you need this? Good point, no I don't. > > +#define WDR_SHORT_TIMEOUT 1000 /* shorter urb timeout */ > > +#define UNIT_US 50 > > +#define IR_TIMEOUT 12500 > > +#define MAX_PACKET 64 > > > > +static int uirt_tx(struct rc_dev *rc, uint *txbuf, uint count) > > +{ > > + struct uirt *uirt = rc->priv; > > + u8 *out; > > + u32 i, dest, unit_raw, freq, len; > > + int err; > > + > > + // streaming tx does not work for short IR; use non-streaming > > + // tx for short IR > > + if (count <= 24) > > + return uirt_short_tx(rc, txbuf, count); > > + > > + out = kmalloc(count * 2 + 3, GFP_KERNEL); > > + if (!out) > > + return -ENOMEM; > > + > > + out[0] = 0x25; // Streaming Transmit > > + out[1] = 0xdb; // checksum > > A constant checksum? Now that is a new concept. Yes, this really needs a comment. It is a checksum over the command, which in this case is just the previous byte. I'll add a comment. > > + out[2] = uirt->freq; // carrier frequency > > + > > + dest = 3; > > + > > + freq = uirt->freq & 0x7f; > > + > > + for (i = 0; i < count; i++) { > > + // width = (us / freq) * 2.5 > > + unit_raw = DIV_ROUND_CLOSEST(txbuf[i] * 5, freq * 2); > > + > > + if (unit_raw == 0) > > + unit_raw = 1; > > + else if (unit_raw > 127) > > + out[dest++] = (unit_raw >> 8) | 0x80; > > + > > + out[dest++] = unit_raw; > > + } > > + > > + len = min_t(u32, dest, MAX_PACKET); > > + > > + uirt->tx_buf = out + len; > > + uirt->tx_len = dest - len; > > + > > + err = uirt_command(uirt, out, len, CMD_STATE_STREAMING_TX); > > + kfree(out); > > + if (err != 0) > > + return err; > > + > > + return count; > > +} > > + > > > > +static int uirt_probe(struct usb_interface *intf, > > + const struct usb_device_id *id) > > +{ > > + struct usb_host_interface *idesc = intf->cur_altsetting; > > + struct usb_device *usbdev = interface_to_usbdev(intf); > > + struct usb_endpoint_descriptor *ep_in = NULL; > > + struct usb_endpoint_descriptor *ep_out = NULL; > > + struct usb_endpoint_descriptor *ep = NULL; > > + struct uirt *uirt; > > + struct rc_dev *rc; > > + struct urb *urb; > > + int i, pipe, err = -ENOMEM; > > + > > + for (i = 0; i < idesc->desc.bNumEndpoints; i++) { > > + ep = &idesc->endpoint[i].desc; > > + > > + if (!ep_in && usb_endpoint_is_bulk_in(ep) && > > + usb_endpoint_maxp(ep) == MAX_PACKET) > > + ep_in = ep; > > + > > + if (!ep_out && usb_endpoint_is_bulk_out(ep) && > > + usb_endpoint_maxp(ep) == MAX_PACKET) > > + ep_out = ep; > > + } > > + > > + if (!ep_in || !ep_out) { > > + dev_err(&intf->dev, "required endpoints not found\n"); > > + return -ENODEV; > > + } > > + > > + uirt = kzalloc(sizeof(*uirt), GFP_KERNEL); > > + if (!uirt) > > + return -ENOMEM; > > + > > + uirt->in = kmalloc(MAX_PACKET, GFP_KERNEL); > > + if (!uirt->in) > > + goto free_uirt; > > + > > + uirt->out = kmalloc(MAX_PACKET, GFP_KERNEL); > > + if (!uirt->out) > > + goto free_uirt; > > + > > + rc = rc_allocate_device(RC_DRIVER_IR_RAW); > > + if (!rc) > > + goto free_uirt; > > + > > + urb = usb_alloc_urb(0, GFP_KERNEL); > > + if (!urb) > > + goto free_rcdev; > > + > > + pipe = usb_rcvbulkpipe(usbdev, ep_in->bEndpointAddress); > > + usb_fill_bulk_urb(urb, usbdev, pipe, uirt->in, MAX_PACKET, > > + uirt_in_callback, uirt); > > + uirt->urb_in = urb; > > + > > + urb = usb_alloc_urb(0, GFP_KERNEL); > > + if (!urb) > > + goto free_rcdev; > > + > > + pipe = usb_sndbulkpipe(usbdev, ep_out->bEndpointAddress); > > + usb_fill_bulk_urb(urb, usbdev, pipe, uirt->out, MAX_PACKET, > > + uirt_out_callback, uirt); > > + > > + uirt->dev = &intf->dev; > > + uirt->usbdev = usbdev; > > + uirt->rc = rc; > > + uirt->urb_out = urb; > > + uirt->rx_state = RX_STATE_INTERSPACE_HIGH; > > + > > + err = usb_submit_urb(uirt->urb_in, GFP_KERNEL); > > + if (err != 0) { > > + dev_err(uirt->dev, "failed to submit read urb: %d\n", > > err); > > + return err; > > Massive memory leak. You cannot just return. Yes, that's broken. Thanks for catching that. I'll go over the error paths. Thanks again for the review, I'll send out v2 when I'm done. Sean
