On 1/7/2021 5:51 PM, John Stultz wrote: > In reviewing the previous patch, Thinh Nguyen pointed out that > the DRD mode change sequence should be like the following when > switching from host -> device according to the programming guide > (for all DRD IPs): > 1. Reset controller with GCTL.CoreSoftReset > 2. Set GCTL.PrtCapDir(device) > 3. Soft reset with DCTL.CSftRst > 4. Then follow up with the initializing registers sequence > > The current code does: > a. Soft reset with DCTL.CSftRst on driver probe > b. Reset controller with GCTL.CoreSoftReset (added in previous > patch) > c. Set GCTL.PrtCapDir(device) > d. < missing DCTL.CSftRst > > e. Then follow up with initializing registers sequence > > So this patch adds the DCTL.CSftRst soft reset that was currently > missing from the dwc3 mode switching. > > Cc: Felipe Balbi <balbi@xxxxxxxxxx> > Cc: Tejas Joglekar <tejas.joglekar@xxxxxxxxxxxx> > Cc: Yang Fei <fei.yang@xxxxxxxxx> > Cc: YongQin Liu <yongqin.liu@xxxxxxxxxx> > Cc: Andrzej Pietrasiewicz <andrzej.p@xxxxxxxxxxxxx> > Cc: Thinh Nguyen <thinhn@xxxxxxxxxxxx> > Cc: Jun Li <lijun.kernel@xxxxxxxxx> > Cc: Mauro Carvalho Chehab <mchehab+huawei@xxxxxxxxxx> > Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> > Cc: linux-usb@xxxxxxxxxxxxxxx > Signed-off-by: John Stultz <john.stultz@xxxxxxxxxx> > --- > Feedback would be appreciated. I'm a little worried I should be > conditionalizing the DCTL.CSftRst on DRD mode controllers, but > I'm really not sure what the right thing to do is for non-DRD > mode controllers. > --- > drivers/usb/dwc3/core.c | 3 +++ > 1 file changed, 3 insertions(+) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index b6a6b90eb2d5..71f8b07ecb99 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -40,6 +40,8 @@ > > #define DWC3_DEFAULT_AUTOSUSPEND_DELAY 5000 /* ms */ > > +static int dwc3_core_soft_reset(struct dwc3 *dwc); > + > /** > * dwc3_get_dr_mode - Validates and sets dr_mode > * @dwc: pointer to our context structure > @@ -177,6 +179,7 @@ static void __dwc3_set_mode(struct work_struct *work) > > dwc3_set_prtcap(dwc, dwc->desired_dr_role); > > + dwc3_core_soft_reset(dwc); Hi John/Thinh/Felipe, I actually added this change into my local branch, because we were seeing an issue when switching from host mode --> peripheral mode. What was happening was that the RXFIFO register did not update back to the expected value for peripheral mode by the time dwc3_gadget_init_out_endpoint() was executed. With the logic to calculate the EP max packet limit based on RXFIFO reg, this caused all EPs to be set with an EP max limit of 0. With this change, it seemed to help with the above issue. However, can we consider moving the core soft reset outside the spinlock? At least with our PHY init routines, we have some msleep() calls for waiting for the PHYs to be ready, which will end up as a sleeping while atomic bug. (not sure if PHY init is required to be called in atomic context) Thanks Wesley Cheng -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project
