HI Michael,
> -----Original Message-----
> From: Michael Grzeschik <mgr@xxxxxxxxxxxxxx>
> Sent: Monday, February 22, 2021 9:01 PM
> To: Manish Narani <MNARANI@xxxxxxxxxx>
> Cc: gregkh@xxxxxxxxxxxxxxxxxxx; robh+dt@xxxxxxxxxx; Michal Simek
> <michals@xxxxxxxxxx>; balbi@xxxxxxxxxx; p.zabel@xxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; linux-usb@xxxxxxxxxxxxxxx; linux-
> kernel@xxxxxxxxxxxxxxx; git <git@xxxxxxxxxx>; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx
> Subject: Re: [RESEND PATCH v3 2/2] usb: dwc3: Add driver for Xilinx
> platforms
>
> Hi Manish!
>
> On Tue, Dec 15, 2020 at 12:24:51PM +0530, Manish Narani wrote:
> >Add a new driver for supporting Xilinx platforms. This driver is used
> >for some sequence of operations required for Xilinx USB controllers.
> >This driver is also used to choose between PIPE clock coming from SerDes
> >and the Suspend Clock. Before the controller is out of reset, the clock
> >selection should be changed to PIPE clock in order to make the USB
> >controller work. There is a register added in Xilinx USB controller
> >register space for the same.
> >
> >Signed-off-by: Manish Narani <manish.narani@xxxxxxxxxx>
> >---
> > drivers/usb/dwc3/Kconfig | 9 +
> > drivers/usb/dwc3/Makefile | 1 +
> > drivers/usb/dwc3/dwc3-of-simple.c | 1 -
> > drivers/usb/dwc3/dwc3-xilinx.c | 334
> ++++++++++++++++++++++++++++++
> > 4 files changed, 344 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/usb/dwc3/dwc3-xilinx.c
> >
> >diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
> >index 7a2304565a73..0e00e6dfccd8 100644
> >--- a/drivers/usb/dwc3/Kconfig
> >+++ b/drivers/usb/dwc3/Kconfig
> >@@ -139,4 +139,13 @@ config USB_DWC3_QCOM
> > for peripheral mode support.
> > Say 'Y' or 'M' if you have one such device.
> >
> >+config USB_DWC3_XILINX
> >+ tristate "Xilinx Platforms"
> >+ depends on (ARCH_ZYNQMP || ARCH_VERSAL) && OF
> >+ default USB_DWC3
> >+ help
> >+ Support Xilinx SoCs with DesignWare Core USB3 IP.
> >+ This driver handles both ZynqMP and Versal SoC operations.
> >+ Say 'Y' or 'M' if you have one such device.
> >+
> > endif
> >diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
> >index ae86da0dc5bd..add567578b1f 100644
> >--- a/drivers/usb/dwc3/Makefile
> >+++ b/drivers/usb/dwc3/Makefile
> >@@ -51,3 +51,4 @@ obj-$(CONFIG_USB_DWC3_MESON_G12A) +=
> dwc3-meson-g12a.o
> > obj-$(CONFIG_USB_DWC3_OF_SIMPLE) += dwc3-of-simple.o
> > obj-$(CONFIG_USB_DWC3_ST) += dwc3-st.o
> > obj-$(CONFIG_USB_DWC3_QCOM) += dwc3-qcom.o
> >+obj-$(CONFIG_USB_DWC3_XILINX) += dwc3-xilinx.o
> >diff --git a/drivers/usb/dwc3/dwc3-of-simple.c b/drivers/usb/dwc3/dwc3-
> of-simple.c
> >index e62ecd22b3ed..71fd620c5161 100644
> >--- a/drivers/usb/dwc3/dwc3-of-simple.c
> >+++ b/drivers/usb/dwc3/dwc3-of-simple.c
> >@@ -172,7 +172,6 @@ static const struct dev_pm_ops
> dwc3_of_simple_dev_pm_ops = {
> >
> > static const struct of_device_id of_dwc3_simple_match[] = {
> > { .compatible = "rockchip,rk3399-dwc3" },
> >- { .compatible = "xlnx,zynqmp-dwc3" },
> > { .compatible = "cavium,octeon-7130-usb-uctl" },
> > { .compatible = "sprd,sc9860-dwc3" },
> > { .compatible = "allwinner,sun50i-h6-dwc3" },
> >diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-
> xilinx.c
> >new file mode 100644
> >index 000000000000..7e485951d2f7
> >--- /dev/null
> >+++ b/drivers/usb/dwc3/dwc3-xilinx.c
> >@@ -0,0 +1,334 @@
> >+// SPDX-License-Identifier: GPL-2.0
> >+/**
> >+ * dwc3-xilinx.c - Xilinx DWC3 controller specific glue driver
> >+ *
> >+ * Authors: Manish Narani <manish.narani@xxxxxxxxxx>
> >+ * Anurag Kumar Vulisha <anurag.kumar.vulisha@xxxxxxxxxx>
> >+ */
> >+
> >+#include <linux/module.h>
> >+#include <linux/kernel.h>
> >+#include <linux/slab.h>
> >+#include <linux/clk.h>
> >+#include <linux/of.h>
> >+#include <linux/platform_device.h>
> >+#include <linux/dma-mapping.h>
> >+#include <linux/of_platform.h>
> >+#include <linux/pm_runtime.h>
> >+#include <linux/reset.h>
> >+#include <linux/of_address.h>
> >+#include <linux/delay.h>
> >+#include <linux/firmware/xlnx-zynqmp.h>
> >+#include <linux/io.h>
> >+
> >+#include <linux/phy/phy.h>
> >+
> >+/* USB phy reset mask register */
> >+#define XLNX_USB_PHY_RST_EN 0x001C
> >+#define XLNX_PHY_RST_MASK 0x1
> >+
> >+/* Xilinx USB 3.0 IP Register */
> >+#define XLNX_USB_TRAFFIC_ROUTE_CONFIG 0x005C
> >+#define XLNX_USB_TRAFFIC_ROUTE_FPD 0x1
> >+
> >+/* Versal USB Reset ID */
> >+#define VERSAL_USB_RESET_ID 0xC104036
> >+
> >+#define XLNX_USB_FPD_PIPE_CLK 0x7c
> >+#define PIPE_CLK_DESELECT 1
> >+#define PIPE_CLK_SELECT 0
> >+#define XLNX_USB_FPD_POWER_PRSNT 0x80
> >+#define PIPE_POWER_ON 1
> >+#define PIPE_POWER_OFF 0
> >+
> >+struct dwc3_xlnx {
> >+ int num_clocks;
> >+ struct clk_bulk_data *clks;
> >+ struct device *dev;
> >+ void __iomem *regs;
> >+ int (*pltfm_init)(struct dwc3_xlnx *data);
> >+};
> >+
> >+static void dwc3_xlnx_mask_phy_rst(struct dwc3_xlnx *priv_data, bool
> mask)
> >+{
> >+ u32 reg;
> >+
> >+ /*
> >+ * Enable or disable ULPI PHY reset from USB Controller.
> >+ * This does not actually reset the phy, but just controls
> >+ * whether USB controller can or cannot reset ULPI PHY.
> >+ */
> >+ reg = readl(priv_data->regs + XLNX_USB_PHY_RST_EN);
> >+
> >+ if (mask)
> >+ reg &= ~XLNX_PHY_RST_MASK;
> >+ else
> >+ reg |= XLNX_PHY_RST_MASK;
> >+
> >+ writel(reg, priv_data->regs + XLNX_USB_PHY_RST_EN);
> >+}
> >+
> >+static int dwc3_xlnx_init_versal(struct dwc3_xlnx *priv_data)
> >+{
> >+ struct device *dev = priv_data->dev;
> >+ int ret;
> >+
> >+ dwc3_xlnx_mask_phy_rst(priv_data, false);
> >+
> >+ /* Assert and De-assert reset */
> >+ ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
> >+ PM_RESET_ACTION_ASSERT);
> >+ if (ret < 0) {
> >+ dev_err_probe(dev, ret, "failed to assert Reset\n");
> >+ return ret;
> >+ }
> >+
> >+ ret = zynqmp_pm_reset_assert(VERSAL_USB_RESET_ID,
> >+ PM_RESET_ACTION_RELEASE);
> >+ if (ret < 0) {
> >+ dev_err_probe(dev, ret, "failed to De-assert Reset\n");
> >+ return ret;
> >+ }
> >+
> >+ dwc3_xlnx_mask_phy_rst(priv_data, true);
> >+
> >+ return 0;
> >+}
> >+
> >+static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
> >+{
> >+ struct device *dev = priv_data->dev;
> >+ struct reset_control *crst, *hibrst, *apbrst;
> >+ struct phy *usb3_phy;
> >+ int ret;
> >+ u32 reg;
> >+
> >+ crst = devm_reset_control_get_exclusive(dev, "usb_crst");
> >+ if (IS_ERR(crst)) {
> >+ ret = PTR_ERR(crst);
> >+ dev_err_probe(dev, ret,
> >+ "failed to get core reset signal\n");
> >+ goto err;
> >+ }
> >+
> >+ hibrst = devm_reset_control_get_exclusive(dev, "usb_hibrst");
> >+ if (IS_ERR(hibrst)) {
> >+ ret = PTR_ERR(hibrst);
> >+ dev_err_probe(dev, ret,
> >+ "failed to get hibernation reset signal\n");
> >+ goto err;
> >+ }
> >+
> >+ apbrst = devm_reset_control_get_exclusive(dev, "usb_apbrst");
> >+ if (IS_ERR(apbrst)) {
> >+ ret = PTR_ERR(apbrst);
> >+ dev_err_probe(dev, ret,
> >+ "failed to get APB reset signal\n");
> >+ goto err;
> >+ }
> >+
> >+ ret = reset_control_assert(crst);
> >+ if (ret < 0) {
> >+ dev_err(dev, "Failed to assert core reset\n");
> >+ goto err;
> >+ }
> >+
> >+ ret = reset_control_assert(hibrst);
> >+ if (ret < 0) {
> >+ dev_err(dev, "Failed to assert hibernation reset\n");
> >+ goto err;
> >+ }
> >+
> >+ ret = reset_control_assert(apbrst);
> >+ if (ret < 0) {
> >+ dev_err(dev, "Failed to assert APB reset\n");
> >+ goto err;
> >+ }
> >+
> >+ usb3_phy = devm_phy_get(dev, "usb3-phy");
>
> You should move this phy get to probe code and skip the call of
> pltfm_init if no phy was found.
>
> As I understand this glue now, you will set an defined fixed-clock
> frequency from dts in the ps-gtr phy. If no phy and therefor also no
> clock is defined, the call of dwc3_xlnx_init_zynqmp can be skipped, as
> you will not need to switch the clocks to an external lane source.
>
> For example for the host case with node option dr_mode = "host" set and
> no external physical external clksrc connected, this glue still needs to
> be used. The current version would break this case.
OK Michael. I will take care of the same in the next version of the driver.
Thanks,
Manish
>
> Thanks,
> Michael
>
> >+ ret = phy_init(usb3_phy);
> >+ if (ret < 0) {
> >+ phy_exit(usb3_phy);
> >+ goto err;
> >+ }
> >+
> >+ ret = reset_control_deassert(apbrst);
> >+ if (ret < 0) {
> >+ dev_err(dev, "Failed to release APB reset\n");
> >+ goto err;
> >+ }
> >+
> >+ /* Set PIPE Power Present signal in FPD Power Present Register*/
> >+ writel(PIPE_POWER_ON, priv_data->regs +
> XLNX_USB_FPD_POWER_PRSNT);
> >+
> >+ /* Set the PIPE Clock Select bit in FPD PIPE Clock register */
> >+ writel(PIPE_CLK_SELECT, priv_data->regs +
> XLNX_USB_FPD_PIPE_CLK);
> >+
> >+ ret = reset_control_deassert(crst);
> >+ if (ret < 0) {
> >+ dev_err(dev, "Failed to release core reset\n");
> >+ goto err;
> >+ }
> >+
> >+ ret = reset_control_deassert(hibrst);
> >+ if (ret < 0) {
> >+ dev_err(dev, "Failed to release hibernation reset\n");
> >+ goto err;
> >+ }
> >+
> >+ ret = phy_power_on(usb3_phy);
> >+ if (ret < 0) {
> >+ phy_exit(usb3_phy);
> >+ goto err;
> >+ }
> >+
> >+ /*
> >+ * This routes the USB DMA traffic to go through FPD path instead
> >+ * of reaching DDR directly. This traffic routing is needed to
> >+ * make SMMU and CCI work with USB DMA.
> >+ */
> >+ if (of_dma_is_coherent(dev->of_node) ||
> device_iommu_mapped(dev)) {
> >+ reg = readl(priv_data->regs +
> XLNX_USB_TRAFFIC_ROUTE_CONFIG);
> >+ reg |= XLNX_USB_TRAFFIC_ROUTE_FPD;
> >+ writel(reg, priv_data->regs +
> XLNX_USB_TRAFFIC_ROUTE_CONFIG);
> >+ }
> >+
> >+err:
> >+ return ret;
> >+}
> >+
> >+static const struct of_device_id dwc3_xlnx_of_match[] = {
> >+ {
> >+ .compatible = "xlnx,zynqmp-dwc3",
> >+ .data = &dwc3_xlnx_init_zynqmp,
> >+ },
> >+ {
> >+ .compatible = "xlnx,versal-dwc3",
> >+ .data = &dwc3_xlnx_init_versal,
> >+ },
> >+ { /* Sentinel */ }
> >+};
> >+MODULE_DEVICE_TABLE(of, dwc3_xlnx_of_match);
> >+
> >+static int dwc3_xlnx_probe(struct platform_device *pdev)
> >+{
> >+ struct dwc3_xlnx *priv_data;
> >+ struct device *dev = &pdev->dev;
> >+ struct device_node *np = dev->of_node;
> >+ const struct of_device_id *match;
> >+ void __iomem *regs;
> >+ int ret;
> >+
> >+ priv_data = devm_kzalloc(dev, sizeof(*priv_data), GFP_KERNEL);
> >+ if (!priv_data)
> >+ return -ENOMEM;
> >+
> >+ regs = devm_platform_ioremap_resource(pdev, 0);
> >+ if (IS_ERR(regs)) {
> >+ ret = PTR_ERR(regs);
> >+ dev_err_probe(dev, ret, "failed to map registers\n");
> >+ return ret;
> >+ }
> >+
> >+ match = of_match_node(dwc3_xlnx_of_match, pdev->dev.of_node);
> >+
> >+ priv_data->pltfm_init = match->data;
> >+ priv_data->regs = regs;
> >+ priv_data->dev = dev;
> >+
> >+ platform_set_drvdata(pdev, priv_data);
> >+
> >+ ret = devm_clk_bulk_get_all(priv_data->dev, &priv_data->clks);
> >+ if (ret < 0)
> >+ return ret;
> >+
> >+ priv_data->num_clocks = ret;
> >+
> >+ ret = clk_bulk_prepare_enable(priv_data->num_clocks, priv_data-
> >clks);
> >+ if (ret)
> >+ return ret;
> >+
> >+ ret = priv_data->pltfm_init(priv_data);
> >+ if (ret)
> >+ goto err_clk_put;
> >+
> >+ ret = of_platform_populate(np, NULL, NULL, dev);
> >+ if (ret)
> >+ goto err_clk_put;
> >+
> >+ pm_runtime_set_active(dev);
> >+ pm_runtime_enable(dev);
> >+ pm_suspend_ignore_children(dev, false);
> >+ pm_runtime_get_sync(dev);
> >+
> >+ return 0;
> >+
> >+err_clk_put:
> >+ clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data-
> >clks);
> >+ clk_bulk_put_all(priv_data->num_clocks, priv_data->clks);
> >+
> >+ return ret;
> >+}
> >+
> >+static int dwc3_xlnx_remove(struct platform_device *pdev)
> >+{
> >+ struct dwc3_xlnx *priv_data = platform_get_drvdata(pdev);
> >+ struct device *dev = &pdev->dev;
> >+
> >+ of_platform_depopulate(dev);
> >+
> >+ clk_bulk_disable_unprepare(priv_data->num_clocks, priv_data-
> >clks);
> >+ clk_bulk_put_all(priv_data->num_clocks, priv_data->clks);
> >+ priv_data->num_clocks = 0;
> >+
> >+ pm_runtime_disable(dev);
> >+ pm_runtime_put_noidle(dev);
> >+ pm_runtime_set_suspended(dev);
> >+
> >+ return 0;
> >+}
> >+
> >+static int __maybe_unused dwc3_xlnx_suspend_common(struct device
> *dev)
> >+{
> >+ struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
> >+
> >+ clk_bulk_disable(priv_data->num_clocks, priv_data->clks);
> >+
> >+ return 0;
> >+}
> >+
> >+static int __maybe_unused dwc3_xlnx_resume_common(struct device
> *dev)
> >+{
> >+ struct dwc3_xlnx *priv_data = dev_get_drvdata(dev);
> >+
> >+ return clk_bulk_enable(priv_data->num_clocks, priv_data->clks);
> >+}
> >+
> >+static int __maybe_unused dwc3_xlnx_runtime_idle(struct device *dev)
> >+{
> >+ pm_runtime_mark_last_busy(dev);
> >+ pm_runtime_autosuspend(dev);
> >+
> >+ return 0;
> >+}
> >+
> >+static UNIVERSAL_DEV_PM_OPS(dwc3_xlnx_dev_pm_ops,
> dwc3_xlnx_suspend_common,
> >+ dwc3_xlnx_resume_common,
> dwc3_xlnx_runtime_idle);
> >+
> >+static struct platform_driver dwc3_xlnx_driver = {
> >+ .probe = dwc3_xlnx_probe,
> >+ .remove = dwc3_xlnx_remove,
> >+ .driver = {
> >+ .name = "dwc3-xilinx",
> >+ .of_match_table = dwc3_xlnx_of_match,
> >+ .pm = &dwc3_xlnx_dev_pm_ops,
> >+ },
> >+};
> >+
> >+module_platform_driver(dwc3_xlnx_driver);
> >+
> >+MODULE_LICENSE("GPL v2");
> >+MODULE_DESCRIPTION("Xilinx DWC3 controller specific glue driver");
> >+MODULE_AUTHOR("Manish Narani <manish.narani@xxxxxxxxxx>");
> >+MODULE_AUTHOR("Anurag Kumar Vulisha
> <anurag.kumar.vulisha@xxxxxxxxxx>");
> >--
> >2.17.1
> >
> >
> >_______________________________________________
> >linux-arm-kernel mailing list
> >linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> >http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
>
> --
> Pengutronix e.K. | |
> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
