Re: [PATCH v6 6/7] dt-bindings: connector: Add SVDM VDO properties

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Feb 12, 2021 at 12:21 PM Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
>
> On Fri, Feb 05, 2021 at 11:34:14AM +0800, Kyle Tso wrote:
> > Add bindings of VDO properties of USB PD SVDM so that they can be
> > used in device tree.
> >
> > Signed-off-by: Kyle Tso <kyletso@xxxxxxxxxx>
>
> Reviewed-by: Guenter Roeck <linux@xxxxxxxxxxxx>
>
> Would it be possible to unify the dt definitions with the definitions
> in include/linux/usb/pd_vdo.h ? I don't really like the duplication.
>
> Thanks,
> Guenter
>

That's my question as well.
But I don't know how to do that.
Is it doable to include "include/linux/usb/pd_vdo.h" in the dt-bindings?

thanks,
Kyle

> > ---
> > Changes since v5:
> > - no change
> >
> >  .../bindings/connector/usb-connector.yaml     |  11 +
> >  include/dt-bindings/usb/pd.h                  | 311 +++++++++++++++++-
> >  2 files changed, 321 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/connector/usb-connector.yaml b/Documentation/devicetree/bindings/connector/usb-connector.yaml
> > index 4286ed767a0a..d385026944ec 100644
> > --- a/Documentation/devicetree/bindings/connector/usb-connector.yaml
> > +++ b/Documentation/devicetree/bindings/connector/usb-connector.yaml
> > @@ -137,6 +137,17 @@ properties:
> >      maxItems: 7
> >      $ref: /schemas/types.yaml#/definitions/uint32-array
> >
> > +  sink-vdos:
> > +    description: An array of u32 with each entry (VDM Objects) providing additional information
> > +      corresponding to the product, the detailed bit definitions and the order of each VDO can be
> > +      found in "USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10"
> > +      chapter 6.4.4.3.1 Discover Identity. User can specify the VDO array via
> > +      VDO_IDH/_CERT/_PRODUCT/_UFP/_DFP/_PCABLE/_ACABLE(1/2)/_VPD() defined in
> > +      dt-bindings/usb/pd.h.
> > +    minItems: 3
> > +    maxItems: 6
> > +    $ref: /schemas/types.yaml#/definitions/uint32-array
> > +
> >    op-sink-microwatt:
> >      description: Sink required operating power in microwatt, if source can't
> >        offer the power, Capability Mismatch is set. Required for power sink and
> > diff --git a/include/dt-bindings/usb/pd.h b/include/dt-bindings/usb/pd.h
> > index 0352893697f0..fef3ef65967f 100644
> > --- a/include/dt-bindings/usb/pd.h
> > +++ b/include/dt-bindings/usb/pd.h
> > @@ -93,4 +93,313 @@
> >  #define FRS_DEFAULT_POWER      1
> >  #define FRS_5V_1P5A            2
> >  #define FRS_5V_3A              3
> > - #endif /* __DT_POWER_DELIVERY_H */
> > +
> > +/*
> > + * SVDM Identity Header
> > + * --------------------
> > + * <31>     :: data capable as a USB host
> > + * <30>     :: data capable as a USB device
> > + * <29:27>  :: product type (UFP / Cable / VPD)
> > + * <26>     :: modal operation supported (1b == yes)
> > + * <25:23>  :: product type (DFP) (SVDM version 2.0+ only; set to zero in version 1.0)
> > + * <22:21>  :: connector type (SVDM version 2.0+ only; set to zero in version 1.0)
> > + * <20:16>  :: Reserved, Shall be set to zero
> > + * <15:0>   :: USB-IF assigned VID for this cable vendor
> > + */
> > +/* SOP Product Type (UFP) */
> > +#define IDH_PTYPE_NOT_UFP       0
> > +#define IDH_PTYPE_HUB           1
> > +#define IDH_PTYPE_PERIPH        2
> > +#define IDH_PTYPE_PSD           3
> > +#define IDH_PTYPE_AMA           5
> > +
> > +/* SOP' Product Type (Cable Plug / VPD) */
> > +#define IDH_PTYPE_NOT_CABLE     0
> > +#define IDH_PTYPE_PCABLE        3
> > +#define IDH_PTYPE_ACABLE        4
> > +#define IDH_PTYPE_VPD           6
> > +
> > +/* SOP Product Type (DFP) */
> > +#define IDH_PTYPE_NOT_DFP       0
> > +#define IDH_PTYPE_DFP_HUB       1
> > +#define IDH_PTYPE_DFP_HOST      2
> > +#define IDH_PTYPE_DFP_PB        3
> > +
> > +#define VDO_IDH(usbh, usbd, ufp_cable, is_modal, dfp, conn, vid)                \
> > +     ((usbh) << 31 | (usbd) << 30 | ((ufp_cable) & 0x7) << 27                \
> > +      | (is_modal) << 26 | ((dfp) & 0x7) << 23 | ((conn) & 0x3) << 21        \
> > +      | ((vid) & 0xffff))
> > +
> > +/*
> > + * Cert Stat VDO
> > + * -------------
> > + * <31:0>  : USB-IF assigned XID for this cable
> > + */
> > +#define VDO_CERT(xid)                ((xid) & 0xffffffff)
> > +
> > +/*
> > + * Product VDO
> > + * -----------
> > + * <31:16> : USB Product ID
> > + * <15:0>  : USB bcdDevice
> > + */
> > +#define VDO_PRODUCT(pid, bcd)   (((pid) & 0xffff) << 16 | ((bcd) & 0xffff))
> > +
> > +/*
> > + * UFP VDO (PD Revision 3.0+ only)
> > + * --------
> > + * <31:29> :: UFP VDO version
> > + * <28>    :: Reserved
> > + * <27:24> :: Device capability
> > + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
> > + * <21:11> :: Reserved
> > + * <10:8>  :: Vconn power (AMA only)
> > + * <7>     :: Vconn required (AMA only, 0b == no, 1b == yes)
> > + * <6>     :: Vbus required (AMA only, 0b == yes, 1b == no)
> > + * <5:3>   :: Alternate modes
> > + * <2:0>   :: USB highest speed
> > + */
> > +/* UFP VDO Version */
> > +#define UFP_VDO_VER1_2               2
> > +
> > +/* Device Capability */
> > +#define DEV_USB2_CAPABLE     BIT(0)
> > +#define DEV_USB2_BILLBOARD   BIT(1)
> > +#define DEV_USB3_CAPABLE     BIT(2)
> > +#define DEV_USB4_CAPABLE     BIT(3)
> > +
> > +/* Connector Type */
> > +#define UFP_RECEPTACLE               2
> > +#define UFP_CAPTIVE          3
> > +
> > +/* Vconn Power (AMA only, set to AMA_VCONN_NOT_REQ if Vconn is not required) */
> > +#define AMA_VCONN_PWR_1W     0
> > +#define AMA_VCONN_PWR_1W5    1
> > +#define AMA_VCONN_PWR_2W     2
> > +#define AMA_VCONN_PWR_3W     3
> > +#define AMA_VCONN_PWR_4W     4
> > +#define AMA_VCONN_PWR_5W     5
> > +#define AMA_VCONN_PWR_6W     6
> > +
> > +/* Vconn Required (AMA only) */
> > +#define AMA_VCONN_NOT_REQ    0
> > +#define AMA_VCONN_REQ                1
> > +
> > +/* Vbus Required (AMA only) */
> > +#define AMA_VBUS_REQ         0
> > +#define AMA_VBUS_NOT_REQ     1
> > +
> > +/* Alternate Modes */
> > +#define UFP_ALTMODE_NOT_SUPP 0
> > +#define UFP_ALTMODE_TBT3     BIT(0)
> > +#define UFP_ALTMODE_RECFG    BIT(1)
> > +#define UFP_ALTMODE_NO_RECFG BIT(2)
> > +
> > +/* USB Highest Speed */
> > +#define UFP_USB2_ONLY                0
> > +#define UFP_USB32_GEN1               1
> > +#define UFP_USB32_4_GEN2     2
> > +#define UFP_USB4_GEN3                3
> > +
> > +#define VDO_UFP(ver, cap, conn, vcpwr, vcr, vbr, alt, spd)                   \
> > +     (((ver) & 0x7) << 29 | ((cap) & 0xf) << 24 | ((conn) & 0x3) << 22       \
> > +      | ((vcpwr) & 0x7) << 8 | (vcr) << 7 | (vbr) << 6 | ((alt) & 0x7) << 3  \
> > +      | ((spd) & 0x7))
> > +
> > +/*
> > + * DFP VDO (PD Revision 3.0+ only)
> > + * --------
> > + * <31:29> :: DFP VDO version
> > + * <28:27> :: Reserved
> > + * <26:24> :: Host capability
> > + * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
> > + * <21:5>  :: Reserved
> > + * <4:0>   :: Port number
> > + */
> > +#define DFP_VDO_VER1_1               1
> > +#define HOST_USB2_CAPABLE    BIT(0)
> > +#define HOST_USB3_CAPABLE    BIT(1)
> > +#define HOST_USB4_CAPABLE    BIT(2)
> > +#define DFP_RECEPTACLE               2
> > +#define DFP_CAPTIVE          3
> > +
> > +#define VDO_DFP(ver, cap, conn, pnum)                                                \
> > +     (((ver) & 0x7) << 29 | ((cap) & 0x7) << 24 | ((conn) & 0x3) << 22       \
> > +      | ((pnum) & 0x1f))
> > +
> > +/*
> > + * Passive Cable VDO
> > + * ---------
> > + * <31:28> :: Cable HW version
> > + * <27:24> :: Cable FW version
> > + * <23:21> :: VDO version
> > + * <20>    :: Reserved, Shall be set to zero
> > + * <19:18> :: Type-C to Type-C/Captive (10b == C, 11b == Captive)
> > + * <17>    :: Reserved, Shall be set to zero
> > + * <16:13> :: cable latency (0001 == <10ns(~1m length))
> > + * <12:11> :: cable termination type (10b == Vconn not req, 01b == Vconn req)
> > + * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
> > + * <8:7>   :: Reserved, Shall be set to zero
> > + * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
> > + * <4:3>   :: Reserved, Shall be set to zero
> > + * <2:0>   :: USB highest speed
> > + *
> > + * Active Cable VDO 1
> > + * ---------
> > + * <31:28> :: Cable HW version
> > + * <27:24> :: Cable FW version
> > + * <23:21> :: VDO version
> > + * <20>    :: Reserved, Shall be set to zero
> > + * <19:18> :: Connector type (10b == C, 11b == Captive)
> > + * <17>    :: Reserved, Shall be set to zero
> > + * <16:13> :: cable latency (0001 == <10ns(~1m length))
> > + * <12:11> :: cable termination type (10b == one end active, 11b == both ends active VCONN req)
> > + * <10:9>  :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
> > + * <8>     :: SBU supported (0b == supported, 1b == not supported)
> > + * <7>     :: SBU type (0b == passive, 1b == active)
> > + * <6:5>   :: Vbus current handling capability (01b == 3A, 10b == 5A)
> > + * <4>     :: Vbus through cable (0b == no, 1b == yes)
> > + * <3>     :: SOP" controller present? (0b == no, 1b == yes)
> > + * <2:0>   :: USB highest speed
> > + */
> > +/* Cable VDO Version */
> > +#define CABLE_VDO_VER1_0     0
> > +#define CABLE_VDO_VER1_3     3
> > +
> > +/* Connector Type */
> > +#define CABLE_CTYPE          2
> > +#define CABLE_CAPTIVE                3
> > +
> > +/* Cable Latency */
> > +#define CABLE_LATENCY_1M     1
> > +#define CABLE_LATENCY_2M     2
> > +#define CABLE_LATENCY_3M     3
> > +#define CABLE_LATENCY_4M     4
> > +#define CABLE_LATENCY_5M     5
> > +#define CABLE_LATENCY_6M     6
> > +#define CABLE_LATENCY_7M     7
> > +#define CABLE_LATENCY_7M_PLUS        8
> > +
> > +/* Cable Termination Type */
> > +#define PCABLE_VCONN_NOT_REQ 0
> > +#define PCABLE_VCONN_REQ     1
> > +#define ACABLE_ONE_END               2
> > +#define ACABLE_BOTH_END              3
> > +
> > +/* Maximum Vbus Voltage */
> > +#define CABLE_MAX_VBUS_20V   0
> > +#define CABLE_MAX_VBUS_30V   1
> > +#define CABLE_MAX_VBUS_40V   2
> > +#define CABLE_MAX_VBUS_50V   3
> > +
> > +/* Active Cable SBU Supported/Type */
> > +#define ACABLE_SBU_SUPP              0
> > +#define ACABLE_SBU_NOT_SUPP  1
> > +#define ACABLE_SBU_PASSIVE   0
> > +#define ACABLE_SBU_ACTIVE    1
> > +
> > +/* Vbus Current Handling Capability */
> > +#define CABLE_CURR_DEF               0
> > +#define CABLE_CURR_3A                1
> > +#define CABLE_CURR_5A                2
> > +
> > +/* USB Highest Speed */
> > +#define CABLE_USB2_ONLY              0
> > +#define CABLE_USB32_GEN1     1
> > +#define CABLE_USB32_4_GEN2   2
> > +#define CABLE_USB4_GEN3              3
> > +
> > +#define VDO_PCABLE(hw, fw, ver, conn, lat, term, vbm, cur, spd)                      \
> > +     (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21          \
> > +      | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11    \
> > +      | ((vbm) & 0x3) << 9 | ((cur) & 0x3) << 5 | ((spd) & 0x7))
> > +#define VDO_ACABLE1(hw, fw, ver, conn, lat, term, vbm, sbu, sbut, cur, vbt, sopp, spd) \
> > +     (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21          \
> > +      | ((conn) & 0x3) << 18 | ((lat) & 0xf) << 13 | ((term) & 0x3) << 11    \
> > +      | ((vbm) & 0x3) << 9 | (sbu) << 8 | (sbut) << 7 | ((cur) & 0x3) << 5   \
> > +      | (vbt) << 4 | (sopp) << 3 | ((spd) & 0x7))
> > +
> > +/*
> > + * Active Cable VDO 2
> > + * ---------
> > + * <31:24> :: Maximum operating temperature
> > + * <23:16> :: Shutdown temperature
> > + * <15>    :: Reserved, Shall be set to zero
> > + * <14:12> :: U3/CLd power
> > + * <11>    :: U3 to U0 transition mode (0b == direct, 1b == through U3S)
> > + * <10>    :: Physical connection (0b == copper, 1b == optical)
> > + * <9>     :: Active element (0b == redriver, 1b == retimer)
> > + * <8>     :: USB4 supported (0b == yes, 1b == no)
> > + * <7:6>   :: USB2 hub hops consumed
> > + * <5>     :: USB2 supported (0b == yes, 1b == no)
> > + * <4>     :: USB3.2 supported (0b == yes, 1b == no)
> > + * <3>     :: USB lanes supported (0b == one lane, 1b == two lanes)
> > + * <2>     :: Optically isolated active cable (0b == no, 1b == yes)
> > + * <1>     :: Reserved, Shall be set to zero
> > + * <0>     :: USB gen (0b == gen1, 1b == gen2+)
> > + */
> > +/* U3/CLd Power*/
> > +#define ACAB2_U3_CLD_10MW_PLUS       0
> > +#define ACAB2_U3_CLD_10MW    1
> > +#define ACAB2_U3_CLD_5MW     2
> > +#define ACAB2_U3_CLD_1MW     3
> > +#define ACAB2_U3_CLD_500UW   4
> > +#define ACAB2_U3_CLD_200UW   5
> > +#define ACAB2_U3_CLD_50UW    6
> > +
> > +/* Other Active Cable VDO 2 Fields */
> > +#define ACAB2_U3U0_DIRECT    0
> > +#define ACAB2_U3U0_U3S               1
> > +#define ACAB2_PHY_COPPER     0
> > +#define ACAB2_PHY_OPTICAL    1
> > +#define ACAB2_REDRIVER               0
> > +#define ACAB2_RETIMER                1
> > +#define ACAB2_USB4_SUPP              0
> > +#define ACAB2_USB4_NOT_SUPP  1
> > +#define ACAB2_USB2_SUPP              0
> > +#define ACAB2_USB2_NOT_SUPP  1
> > +#define ACAB2_USB32_SUPP     0
> > +#define ACAB2_USB32_NOT_SUPP 1
> > +#define ACAB2_LANES_ONE              0
> > +#define ACAB2_LANES_TWO              1
> > +#define ACAB2_OPT_ISO_NO     0
> > +#define ACAB2_OPT_ISO_YES    1
> > +#define ACAB2_GEN_1          0
> > +#define ACAB2_GEN_2_PLUS     1
> > +
> > +#define VDO_ACABLE2(mtemp, stemp, u3p, trans, phy, ele, u4, hops, u2, u32, lane, iso, gen)   \
> > +     (((mtemp) & 0xff) << 24 | ((stemp) & 0xff) << 16 | ((u3p) & 0x7) << 12  \
> > +      | (trans) << 11 | (phy) << 10 | (ele) << 9 | (u4) << 8                 \
> > +      | ((hops) & 0x3) << 6 | (u2) << 5 | (u32) << 4 | (lane) << 3           \
> > +      | (iso) << 2 | (gen))
> > +
> > +/*
> > + * VPD VDO
> > + * ---------
> > + * <31:28> :: HW version
> > + * <27:24> :: FW version
> > + * <23:21> :: VDO version
> > + * <20:17> :: Reserved, Shall be set to zero
> > + * <16:15> :: Maximum Vbus voltage (00b == 20V, 01b == 30V, 10b == 40V, 11b == 50V)
> > + * <14>    :: Charge through current support (0b == 3A, 1b == 5A)
> > + * <13>    :: Reserved, Shall be set to zero
> > + * <12:7>  :: Vbus impedance
> > + * <6:1>   :: Ground impedance
> > + * <0>     :: Charge through support (0b == no, 1b == yes)
> > + */
> > +#define VPD_VDO_VER1_0               0
> > +#define VPD_MAX_VBUS_20V     0
> > +#define VPD_MAX_VBUS_30V     1
> > +#define VPD_MAX_VBUS_40V     2
> > +#define VPD_MAX_VBUS_50V     3
> > +#define VPDCT_CURR_3A                0
> > +#define VPDCT_CURR_5A                1
> > +#define VPDCT_NOT_SUPP               0
> > +#define VPDCT_SUPP           1
> > +
> > +#define VDO_VPD(hw, fw, ver, vbm, curr, vbi, gi, ct)                 \
> > +     (((hw) & 0xf) << 28 | ((fw) & 0xf) << 24 | ((ver) & 0x7) << 21  \
> > +      | ((vbm) & 0x3) << 15 | (curr) << 14 | ((vbi) & 0x3f) << 7     \
> > +      | ((gi) & 0x3f) << 1 | (ct))
> > +
> > +#endif /* __DT_POWER_DELIVERY_H */
> > --
> > 2.30.0.365.g02bc693789-goog
> >



[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux