Hi all,
I use a nxp isp1760 connected to a freescale mpc8270 (custom board).
I'm using the driver from the kernel tree. the controller is well
initialized and my devices are created by udev.
The running kernel is a 2.6.26.8.
I have problems when I try to access to my device /dev/sda1 either
with dd, fdisk or mount.
#fdisk /dev/sda
Reloading ptd c79621e0/c7daf140... qh c796334c readed: 512 of 4096
done: 0000001
Reloading ptd c7962200/c7daf1c0... qh c796334c readed: 0 of 4096 done:
000000001
Reloading ptd c7962220/c7daf240... qh c796334c readed: 0 of 4096 done:
000000001
INFO: task usb-storage:1468 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
usb-storage D 00000000 0 1468 2
Call Trace:
[c7ea3d30] [c000aa40] __switch_to+0x4c/0x6c
[c7ea3d50] [c0214b5c] schedule+0x178/0x2fc
[c7ea3d90] [c0214f24] schedule_timeout+0x98/0xe4
[c7ea3dd0] [c0214828] wait_for_common+0x98/0x1a4
[c7ea3e10] [c90c9514] usb_sg_wait+0x1a4/0x1d0 [usbcore]
[c7ea3e40] [c90e3b04] usb_stor_bulk_transfer_sglist+0x100/0x164
[usb_storage]
[c7ea3e70] [c90e3bfc] usb_stor_bulk_srb+0x28/0x4c [usb_storage]
[c7ea3ea0] [c90e4244] usb_stor_Bulk_transport+0x198/0x4e4 [usb_storage]
[c7ea3ee0] [c90e45bc] usb_stor_invoke_transport+0x2c/0x3a0 [usb_storage]
[c7ea3f50] [c90e2d08] usb_stor_transparent_scsi_command+0x10/0x20
[usb_storage]
[c7ea3f60] [c90e5040] usb_stor_control_thread+0x170/0x2f0 [usb_storage]
[c7ea3fd0] [c002dcec] kthread+0x48/0x84
[c7ea3ff0] [c0005e18] kernel_thread+0x44/0x60
I think i have the turnarround error described by NXP in their FAQ.
But reading the messages of the mailing list, I think i am not the
only only one in this case and the problem comes often from the mass
storage devices.
It might appends that during a data transfer, the devices stops
sending an ack and the host received only part of the data which might
lead to problems.
Here is the complete trace :
#modprobe isp1760
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
isp1760 isp1760.0: NXP ISP1760 USB Host Controller
isp1760 isp1760.0: new USB bus registered, assigned bus number 1
#### ISP1760 ID = 0x61176117
isp1760 isp1760.0: detected 16-bit big endian bus
isp1760 isp1760.0: irq 25, io mem 0x60000000
isp1760 isp1760.0: USB ISP 1761 HW rev. 1 started
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: NXP ISP1760 USB Host Controller
usb usb1: Manufacturer: Linux 2.6.26.8-svn30-dirty1 isp1760-hcd
usb usb1: SerialNumber: isp1760.0
ISP1760 USB device initialised
root@ppc_target:~ port 1 high speed
usb 1-1: new high speed USB device using isp1760 and address 2
port 1 high speed
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
usb 1-1: New USB device found, idVendor=0471, idProduct=3526
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: ISP1520
usb 1-1: Manufacturer: Philips Semiconductors
transfer active bit is set DW3
nak counter: 0, rl: 0
transfer active bit is set DW3
nak counter: 0, rl: 0
usb 1-1.1: new high speed USB device using isp1760 and address 3
usb 1-1.1: configuration #1 chosen from 1 choice
usb 1-1.1: New USB device found, idVendor=058f, idProduct=6387
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: Flash Disk
usb 1-1.1: Manufacturer: USB2.0
usb 1-1.1: SerialNumber: 18002B87
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Error in do_atl_int().
IN dw0: 08000021 dw1: 18040000 dw2: 00a00100 dw3: 00000043 dw4:
00000000 dw5: 00
scsi 0:0:0:0: Direct-Access USB2.0 Flash Disk 8.07 PQ: 0
ANSI: 2
sd 0:0:0:0: [sda] 3891200 512-byte hardware sectors (1992 MB)
Error in do_atl_int().
IN dw0: 68000028 dw1: 19240000 dw2: 00a00100 dw3: 00000043 dw4:
00000000 dw5: 00
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 3891200 512-byte hardware sectors (1992 MB)
Error in do_atl_int().
IN dw0: 68000028 dw1: 19240000 dw2: 00a00100 dw3: 00000043 dw4:
00000000 dw5: 00
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda:<7>usb-storage: queuecommand called
Reloading ptd c7962380/c7daf840... qh c796334c readed: 0 of 4096 done:
000000001
sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
#fdisk /dev/sda
Reloading ptd c79621e0/c7daf140... qh c796334c readed: 512 of 4096
done: 0000001
Reloading ptd c7962200/c7daf1c0... qh c796334c readed: 0 of 4096 done:
000000001
Reloading ptd c7962220/c7daf240... qh c796334c readed: 0 of 4096 done:
000000001
I have my 3 devices created by udev :
root@ppc_target:~ ll /dev/sda*
brw-rw---- 1 root root 8, 0 Jan 1 01:15 /dev/sda
brw-rw---- 1 root root 8, 1 Jan 1 01:15 /dev/sda1
Here is the complete trace in the dmesg
oot@ppc_target:~ dmesg
ge: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 36 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
scsi 0:0:0:0: Direct-Access USB2.0 Flash Disk 8.07 PQ: 0
ANSI: 2
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x3 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3 R 18 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0xf0, key: 0x6, ASC: 0x28, ASCQ: 0x0
usb-storage: Unit Attention: Not ready to ready change, medium may
have changed
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x4 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x5 L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 8 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 0:0:0:0: [sda] 3891200 512-byte hardware sectors (1992 MB)
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 c0 00
usb-storage: Bulk Command S 0x43425355 T 0x6 L 192 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
isp1760 isp1760.0: short bulk, 4 instead 192 with URB_SHORT_NOT_OK flag.
usb-storage: Status code -121; transferred 4/192
usb-storage: -- short read transfer
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
Error in do_atl_int().
IN dw0: 68000028 dw1: 19240000 dw2: 00a00100 dw3: 00000043 dw4:
00000000 dw5: 00000000 dw6: 00000000 dw7: 00000000
usb-storage: Status code -32; transferred 0/13
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82
len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x6 R 188 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage: 1e 00 00 00 01 00
usb-storage: Bulk Command S 0x43425355 T 0x8 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x9 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x9 R 18 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0xf0, key: 0x5, ASC: 0x24, ASCQ: 0x0
usb-storage: Illegal Request: Invalid field in cdb
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xa L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xb L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xb R 8 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 0:0:0:0: [sda] 3891200 512-byte hardware sectors (1992 MB)
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage: 1a 00 3f 00 c0 00
usb-storage: Bulk Command S 0x43425355 T 0xc L 192 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
isp1760 isp1760.0: short bulk, 4 instead 192 with URB_SHORT_NOT_OK flag.
usb-storage: Status code -121; transferred 4/192
usb-storage: -- short read transfer
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
Error in do_atl_int().
IN dw0: 68000028 dw1: 19240000 dw2: 00a00100 dw3: 00000043 dw4:
00000000 dw5: 00000000 dw6: 00000000 dw7: 00000000
usb-storage: Status code -32; transferred 0/13
usb-storage: clearing endpoint halt for pipe 0xc0010380
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=82
len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xc R 188 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0xd L 4096 F 128 Trg 0 LUN 0
CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
Reloading ptd c7962380/c7daf840... qh c796334c readed: 0 of 4096 done:
00000000 cur: 00000001
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xe L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xe R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 20 00
usb-storage: Bulk Command S 0x43425355 T 0xf L 16384 F 128 Trg 0 LUN 0
CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 16384 bytes, 4 entries
Reloading ptd c79621e0/c7daf140... qh c796334c readed: 512 of 4096
done: 00000000 cur: 00000001
Reloading ptd c7962200/c7daf1c0... qh c796334c readed: 0 of 4096 done:
00000000 cur: 00000001
isp1760 isp1760.0: short bulk, 13 instead 4096 with URB_SHORT_NOT_OK
flag.
Reloading ptd c7962220/c7daf240... qh c796334c readed: 0 of 4096 done:
00000000 cur: 00000001
usb-storage: command_abort called
usb-storage: usb_stor_stop_transport called
usb-storage: -- cancelling sg request
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
